Klimaire KSIX024-H220 Operating manual

Before using your air conditioner, please read
this manual carefully and keep it for future reference.
Read This Manual
Keep this manual where the operator can easily
find them.Inside you will find many helpful hints
on how to use and maintain your air conditioner
properly. Just a little preventative care on your
part can save you a great deal of time and money
over the life of your air conditioner. You'll find many
answers to common problems in the chart of
troubleshooting tips. If you review the chart of
Troubleshooting Tips first, you may not need
to call for service.
USER'S & INSTALLATION
MANUAL
SERIES
SPLIT TYPE ROOM AIR CONDITIONER

CONTENTS
Safety Precautions
Name Of Each Part
WEEE Warning
1
5
6
7
8
8
10
11
12
13
14
16
17
17
4
Test running
Packing list
Operation
Notices
Care and Maintenance
Troubleshooting
Installation Guide
Selection of the installing position
Installation of the indoor unit
Installation of the outdoor unit
Pipe connection
Electrical connection

WARNING
Safety Precautions
Incorrect operation due to ignoring instruction will cause
harm or damage. The seriousness is classified by the
following indications：
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage to
properties only.
- 1 -
1.This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision.(Only for the AC with CE-MARKING)
2.This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
(Except for the AC with CE-MARKING)
3.The air conditioner must be grounded. Incomplete grounding
may result in electric shocks. Do not connect the earth wire
to the gas pipeline, water pipeline, lightning rod, or telephone
earth wire.
4.Don't pull out the power plug during operating or with wet
hands.
It can cause electric shock or fire.
5.
national wiring regulations.
The appliance shall be installed in accordance with

- 2 -
8.Don't share the socket with other electric appliance,
and use the broken or unstandord cord.
Otherwise, it can cause electric shock even fire.
9.Clean the dust on the plug regularly.
Otherwise the dust mixed, humidity will result in insulation
fault even fire.
10.An earth leakage breaker with rated capacity must be
installed to avoid possible electric shocks.
11.Cut off the main power switch when notusing the unit for a
long time. Otherwise, it may cause product failure or fire.
12.Stop operation and cut off the main power in storm or
hurricane. Operation with windows opened may cause
electric shock.
13.Don't install air conditioner in a place where there is
flammable gas or liquid. The distance between them
should above 1m. It may cause fire.
14.Don't put a finger, a rod or other object into the air
outlet or inlet.
As a fan is rotating at a high speed, it will cause injury.
15.Don't touch the swinging wind vanes.
It may clamp your finger and damage the driving parts of
the wind vanes.
16.Don't attempt to repair the air conditioner by yourself.
You may be hurt or cause further malfunctions.
17.Take care not let the remote control and the indoor unit
watered or being too wet, or may short circuit even caused fire.
18.Don't use liquid or corrosive cleaning agent wipe the
air-conditioner and sprinkle water or other liquid either.
Otherwise the inclosure will be damaged even electric shock.
19.If the power supply cord is damaged, it must be replaced
by the manufacture or its service agent or a similar
qualified person.
Cut off the
power supply
switch
Lig
htning
Danger
6.Don't pull the power cord when pull out the power
plug.
The damage of pulling power cord will cause serious
electric shock.
7.The power plug must be inserted tightly.
Otherwise, it can cause electric shock or overheating,
even fire.

1.Don't install the indoor unit under sunshine directly.
2.Don't block air inlet or air outlet, otherwise, the cooling or heating
capacity will be weakened, even cause system stop operating.
3.Don't apply the cold air to the body for a long time. It will deteriorate
your physical conditions and cause health problems.
4.Close the windows and doors, otherwise, the cooling or heating
capacity will be weakened.
5.If the air filter is very dirty, the cooling or heating capacity will be
weakened. Please clean the air filter regularly .
6.It was prohibited to stand or put things onto the top of the outdoor,
to avoid drop or damage. In no case should children be allowed to
sit on the outdoor unit.
7.Set the suitable temperature, especially there are old people,
children and patients in the room. Generally, keep the temperature
difference for 5℃ between the inside and outside.
8.In case that the unit occurs closing down due to the severe
interference from outer environments such as mobile phone, please
cut off the plug and plug in to restart the air conditioner after
several seconds .
9.It is forbidden to let the air conditioner keep precision
instrumentation, artistic production for long time and make food
fresh, otherwise abnormal using will cause damage and weaken.
10.It is forbidden to let children and the disabled use air-condition
without other adult checking.
11.Open windows frequently after using air-condition for a long time.
12. n
all-pole switch must be installed in the fixed wiring and the distance
between contacts should be no less than 3.0 mm.
If your air conditioner is not fitted with a supply cord and a plug, a
CAUTION
- 3 -
13.If your air conditioner is permanently connected to the fixed wiring
and have a leakage current that may exceed 10 mA. Leakage
protector must be installed in the fixed wiring.
14.The power supply circuit should have leakage protector and air
switch of which the capacity should be more than 1.5 times of the
maximum current.
15. If the equipement emissions cannot meet the technical requirement
of IEC 61000-3-3,Following Attention should be take care.

- 4 -
KSIX024-H220 0.222
Product Type Zmax
Serial No.
1
Attention!
This appliance can be connected only to a supply with system
impedance no more than Zmax.in case necessary, please consult
your supply authority for system impedance information.
WEEE Warning
Do not dispose of electrical appliances as
unsorted municipal waste, use separate
collection facilities.
Contact you local government for information
regarding the collection systems available.
If electrical appliances are disposed of in
landfills or dumps, hazardous substances
can leak into the groundwater and get into
the food chain, damaging your health and
well-being.
When replacing old appliances with new ones, the retailer is
legally obligated to take back your old appliance for disposals
at least free of charge.
Meaning of crossed out wheeled dustbin:

Note:
1.If the power supply from outdoor unit, you can find the power supply card is
fitted in the outdoor unit.
2.The descriptions in this user manual are text and figures may have slightly
difference to the promotion information and actual appliance. Please refer to
the real appliance purchased. Thank you.
- 5 -
Indoor Unit
Name of Each Part
Indoor Unit
Outdoor Unit
1 Front panel、
2 Air filter、
3 Handling switch、
4 Louver 、
5 Signal receptor、
6、Remote controller
7、Drain hose
8、Refrigerant gas/
liquid pipe
10 Cut-off valve、
11 Air outlet cover、
Outdoor Unit
Air inlet
Air inlet
Air outlet
5
1 2
3
4
6
7
8
10
11
★
★
Air outlet
9
9、Supply cord

3
Operation
Manual operation
★
Manual operation
☆
When the remote controller does not work or can not be found, please follow
these steps:
1.As the unit is operating, you can press the "Auto button"
to stop operating.
2.As the unit is stopping, you can press the "Auto button"
to start operating.
☆
Use your hands to move the vertical airflow
vane and change the horizontal wind
direction.
！Note:
a. Adjust the horizontal air flow direction before
the air-conditioner starts. Don't insert your finger
into air intake or outlet vents when the air-conditioner is operating.
b. For appliance with auto pendulum wind function, please refer to "air
conditioner remote controller instruction " for how to adjust horizontal air flow.
Adjusting air flow direction
1. orizontal air flow manually. Adjusting h
Remote controller operation
★
See "air conditioner remote controller instruction "
2. Adjusting vertical air flow direction(up-down)
Refer to air conditioner remote controller instruction" for how to adjust vertical
airflow direction through adjusting the horizontal airflow vane by remote controller.
"
Note:
Adjust the vertical air flow direction by remote controller. When you adjust the
horizontal airflow vane by hand, the machine may cause problem.
When the air-conditioner stops, the horizontal wind vane will close the wind
outlet of air conditioner.
Manual operation can be used temporarily in case you can not use remote
controller or its batteries are exhausted.
！
- 6 -

- 7 -
★
In order to use the air conditioner properly, please refer to its working temperature
range. Otherwise, indoor unit automatic protection function may be activated,
cooling or heating efficiency will be weakened.
Safety tips
The air-conditioner may can’t run in normal followed under mentioned table
★
Notices
1.Make sure that the earth wire is connected safely and reliably.
2.Make sure the filter net is properly fixed.
3.Make sure that air outlet and inlet are not blocked.
4.Please clean the filter before starting the air-conditioner referring to page to 6
"Cleaning"for how to operate.
5.Check to see whether the outdoor install bracket is damage. If yes, please contact
our Service center locally.
Checking before operation
To prevent injury and property damage, Please pay attention to these following before
operating the air conditioner.
N 842/2006： If the air conditioner you bought used the refrigerant R410A, the amount
of refrigerant is in a closed cooling circuit. The coolant does have zero ozone depletion
potential, but is a so-called greenhouse gases under the Kyoto Protocol and may thus
contribute to global warming,if it is released to the atmosphere. Therefore only trained
technicians with refrigerant certificate make a filling or emptying.
GWP: R410A(R32/125:50:50):1950
Notices for R410A models
★
Cooling
Heating
Indoor
Outdoor
Indoor
Outdoor
＜64ºF
＞109ºF (Apply to constant speed)
＞86ºF
＜19ºF (Apply to constant speed)
＞86ºF
＞117ºF (Apply to variable speed)
＞125ºF (Apply toT3)
＜10ºF (Apply to variable speed)

Care and Maintenance
Troubleshooting
1.Turn off the air-conditioner and remove the electrical plug from the outlet.
2.Wipe the indoor unit with dry cloth or wet cloth which is dipped by cold water.
Cleaning the indoor unit
Cleaning
Note :
★
★
☆
！
Cleaning air filter
Maintenance
☆
Air filter
Front panel
Air filter
Front panel
Check the following before requesting on service centre of Klimaire if the malfunction occurs.
Don t use thinner, polishing powder, benzene and other volatile chemicals. '
Don t use water above 45ºC to wash the panel, or it could cause deformation or depigment. '
1.Raise up the front panel of indoor unit until it suddenly stop, then raise up the
protruded part of air filter, a nd then take it out.
2. Use a vacuum cleaner or wash them with water, t hen dry it in the shade.
3. Reinsert the air filter into the indoor unit until being entirely fixed, then close the
front panel.
1. Select FA N operation mode,
make the air conditioner run a
long time to dry.
" " 2. Turn off the air conditioner and cut
off the power supply.
4. Clean air filters and other parts.
3. Take out the batteries from the remote
controller.
Don t use liquid or corrosive detergent clean the appliance and don t splash water or other
liquid onto it , otherwise, it may damage the plastic components, even cause electric shock.
'
Phenomenon Tr ouble shooting
Air conditioner dose
not operate at all
Has the power been shut down?
Is the wiring loose?
Is the voltage higher than 1.1 times of max rated voltage
or lower than 0.9 times of min rated voltage?
Is the fuse burnt?
Does it reach the set time for start up?
- 8 -

Phenomenon Tr oubleshooting
Remote controller is not available
Is the remote controller out of effective
distance to the indoor unit?
Is the battery exhausted?
Are there any obstructions between the
controller and the signal receptor?
Indoor unit does not operate
immediately when the air
conditioner is restarted
Once the air conditioner is stopped,
it will not operate in approximately
3 minutes to protect itself.
There is unusual smell blowing from
the outlet after operation is started.
This is caused by the odour in the
room permeated from building
material, furniture, or smoke.
Sound of water flow can be heard
during cooling operation
This is caused by the refrigerant
flowing inside the unit.
Mist is emitted during cooling
operation.
Mist is emitted during heating
operation.
Because the air of the room is cooled
down rapidly by the cold wind and it
looks like the fog.
This generate due to moisture in
defrosting process.
Low noise can be heard during
operation
A low hissing sound is caused by
the refrigerant flowing.
A low squeak sound is caused by
the deformation of plastic due to
temperature.
Cooling (Heating)efficiency is not
good
Is the setting temperature suitable?
Is the air inlet or outlet obstructed?
Are air filter dirty?
Is indoor fan speed set at low speed?
Is there any heat source in your room?
In case the following situation, please immediately stop all operations and
cut off the power supply, then contact with service centre of Klimaire.
The fuse and switch often breaks.
Carelessly splash water or something into air conditioner.
Unusual noise can be heard during operation.
Electrical wiring and power plug are very hot.
Wind blowing from the outlet smells terrible during operation.
The Run light or other display flashes rapidly and keeps flashing after repluging.
- 9 -

1.Please read the instructions carefully before installation of the
air-conditioner.
2.The installation should be carried out by specialists.
3.Installation the air-conditioner and connecting the pipe and
wires must be strict to reference the instructions.
4.The wiring must be done by qualified electrician according to
the electrical safety requirements.
5.The customer should have a qualified power supply which
coincides with the tag of air conditioner, the normal voltage
should be in the range of 90-110% of its rated voltage.
6.The air conditioner must be well grounded, the switch of the
main power of air-conditioner must be reliably grounded.
Guide for customer
Notices
★
★
1.The air conditioner must be installed on well strong
supporter.
2.The appliance shall be installed in accordance with
national wiring regulations.
3.Fix the machine firmly, otherwise it will produce abnormal
noise and vibration.
4.Install the outdoor unit in the place where it wouldn't
disturb your neighbour.
5.The method of connection of the appliance to the
electrical supply and inter connection of separate
somponents, please see the electric connection elements
shart which stick on the machine.
6.After installation, the power plug should be easily reached.
Installation Guide
- 10 -

Side clearance
above 6 in
The distance between indoor and outdoor unit should be 5 meters and pipe length can
go up to maximum 15 meters with additional refrigerant charge.
Max. Allowable
Tubing Length at
Shipment(ft)
Limit of Tubing
Length(ft)
Limit of Elevation
Difference H(ft)
Requires Amount
of Additional
Refrigerant (oz/ft)
16 50 16 0.21
CC≤12000Btu
CC≥18000Btu
0.32
Selection of the installing position
Indoor Unit
●
●
●
●
●
●
●
There is no heating and
steaming source nearby.
No obstacles for installing
position nearly.
Keep good air circulation.
Convenient to adopt
measures to reduce noises.
Do not install them near the
doorway.
Make sure to have the
distance between the ceiling,
wall, furniture and other
obstacles.
2 meters high above the floor.
●
●
●
●
●
In case that you put up a canopy to protect
it from rains and sunrays, pay attention not
to cause any obstacles for the heating
dispersion for the condenser.
Do not grow animals or plants near the
installation location for the cold and hot air
out will affect them.
Make sure to have the distance specified
in the picture between ceiling, wall,
furniture and other obstacles.
Stay away from heating source and
inflammable air.
The installation base and supporting frame
should be strong and secure. The machine
should be at plane surface.
Outdoor Unit
★
★
- 11 -
Ceiling clearance above 6 in
Side clearance
above 12 in
Front clearance
above 78 in
Top clearance
above 24 in
Back
clearance
above
4 in

- 12 -
●
interconnected pipes to the indoor unit: point to the center of pipe and fasten the
connection screw at first by hand and then by wrench until you hear the " Click "
sound. Fastening direction is shown in the right picture. Using torque is shown
in the following table.
Pull out the indoor unit pipes after detached the fixed parts on them. Connect the
Installation of the indoor unit
Note: The installed air-conditioner
won't be tightly appressed to the
wall if that is not arranged shown in
the picture. The outflow tube must
be in the bottom and the highest
point of it can not exceed the
position of water basin.
Drilling 70mm diameter
pipe hole at the left down
or right down side of the
installation board. The
hole shall slant outward
slightly.
Indoor
70 hole
Pipe
connection
15mm
Outdoor
Ring
Putty
Wall
Wall
Cable
Outflow tube
Connection
pipe
Installation
board Cable
Air-conditioner
Base
Outflow tube
Cable
Connection pipe
Installation board
Wall
Pipe
Spanner
Nut
Spanner
Connection pipe
●
●First make changes to wall and make sure that is hard and
secure. Using four " ＋ " type screws to fasten the installation
board onto the wall. Keep it water lever horizontal direction
and perpendicular in vertical direction. Otherwise it might
cause water drops when air-conditioner is running cooling
operation.
Plastic
strap Cable
Board 1
Connection pipe
Drain pipe
Before installation, confirm connection
pipes' direction.Remove the board 1 and
board 2 on the correct connecting side.
Press connection pipes to the board gap,
then install board 2 to the original location.
If connection pipes are on the other side,
install them as above.
●
Board 2
Board 3
Board 4
put off
●
Drainage pipe can be connected to the
connector 1 and connector 2.If it's
necessary to adjust drainage pipe to the
other connector, remove rubber stopper
from this side and fix drainage pipe to it,
then fix the rubber stopper to the other
connector to make it blocked up.
Attention: Please use tools like screwdriver to insert
into the back hole of the rubber stopper and plug it to
the connector when you want to make the connector
blocked up.
Connector 2 Connector 1
Screwdriver
Rubber
stopper
Dural drainage feature AC can be installed as below chart shows:

- 13 -
25.98 X 10.23 X 16.53 17 11
Outdoor Unit Size of
Shape(W*D*H) (in) A (in) B (in)
Check the water discharge
1. Take off the frame the unit cover.
Take off the front frame for maintenance
according to the following steps:
● Turn perpendicular airflow direction handle from
" I " to horizontal direction.
● As shown in the picture on the right, take off two
covers from the front frame and then unfasten two
fixture screws.
● Pull the front frame towards yourself and take it off.
In case that put the front frame back, turn the perpendicular
airflow direction handle from " I " to horizontal, then
proceed according to the third and the second steps.
You should check whether the front frame is
firmly inside the fixture groove on the top.
2. Check the water discharge.
● Put a cup of water into groove.
● Check whether the water flow through the
water discharge hole.
Bolt
Bolt Vertical airflow
direction plate
Front frame
Pull down the front frame towards your
and take off the front frame.
Installation of the outdoor unit
● The outdoor unit must be firmly fixed to avoid falling in the strong wind.
● Install on the cement base the drawing below.
● If it will be installed at seaside or at a place high above the ground and with strong
wind, the AC should be installed against the wall to ensure the normal operation of
the fan and the blocking plate should be used.
● If it will be installed in type, the structure
of the mounting surface should be made
of solid stick, cement or materials with
equivalent strength, and be of enough
bearing capacity. Otherwise, measures
such as reinforcement, support or
vibration damping should be adopted.
Installation outdoor unit bolt
A
Left installation feet Right installation feet
Air inlet
Outdoor Unit
★
●Arrange the connection pipes, cable, outflow tube according to the figure , then
connect the drain pipe to the draining hole.
●Use insulation sleeve to warp the position of connection pipe and indoor unit, then
wrap the insulating tape on the sleeve to avoid condensate water.
●Fasten connection pipes, cables and drain pipe together by plastic strap.
●Hang the indoor unit to the board
and make sure the machine is in
the middle of the board.
●Pushing the machine towards the
left down and right down side of
the installation board until the
hangers enters tightly the grooves
(it makes "click" sound)
Water discharge pipe
Connection wire
23.62 X 9.84 X 19.29 15.74 11.41
25.98 X 9.44 X 19.68 16.6 10.31
27.55 X 8.85 X 19.68 18 10.31
28.34 X 10.23 X 21.45 21.25 11
29.92 X 10.23 X 21.65 21.25 11
31.1 X 11.41 X 21.45 21.49 12.44
31.49 X 11.81 X 23.22(27.16)
21.25 12.83
32.48 X 11.81 X 25.78 21.25 13.14
35 X 12.59 X 27.55 24.88 13.85
35.43 X 12.59 X 31.29 21 13.85
31.1 X 11 X 21.65
21.49
11.81
H
W
B
D
Air outlet

Pipe connection
● Connect the pipe to the unit: point to the
center of pipe and fasten by wrench
until it is tightly
fastened, the
fastening
direction is in the
following picture.
Indoor unit Pipe
Connection screw
Torque
wrench
Wrench
Connection screw
The size of pipe
6.35mm( )
9.52mm( )
12.7mm( )
15.88mm( )
Torque
18N.m
13.3 lb-ft
42N.m
55N.m
75N.m
1
3
1
5
_
_
_
_
4
8
2
8
● Pointing towards the center of pipe, fasten
the screw with strength.
● Wrench the screw in the end until you hear
the “Click” sound.
Refer the direction to the picture
Outdoor unit
Torque wrench
Side air pipe
Side liquid pipe
The form of pipe
● Wrap up all pipe, water discharge and
connection wire from top to below.
● Cover the connection and fix them with
two plastic rings.
● Wrap up the pipes with tape alongside
the wall and fix them to the wall with
clips. These steps are usually adopted
when outdoor unit is installed below the
indoor unit.
Use sealing tape to
cover the small leaks
on the external ring
of the pipe
Wrap up with tape
Pipes
Water discharge
pipe
Connection wire
Control panel cover
Connection wire
Round in this shape to prevent water
entering the electrical parts
Round shape
Round shape
Use sealing tape to
cover the small leaks
on the external ring of
the pipe
See the picture
on the left
● In case that you want to have
additional water discharge pipe, the
end of pipe should be within certain
distance towards to surface ( don't let
it under the water. Fix it onto the wall
so it won't be swayed by the wind).
● Wrap the pipes and connection wire
well from below to top.
● Wrap up the pipes that are rounded
up by the wall comers in the way
shown in the picture so it can prevent
water entering the room.
● Use clips or other fixture to fasten the
pipes to the walls.
★
- 14 -
31 lb-ft
41 lb-ft
55 lb-ft

Expelling the air in the pipes and the indoor unit
★
Expelling the air: humid air in the
refrigerating system might cause trouble
of compressor.
● Take off the cover from the stop valve
and T-branch valve.
● Take off the auxiliary cover from the
T-branch valve.
● Turn the stop valve rod anti-clock wise
to an angle of 90 degree, keep it open
for 8 seconds and close the valve.
● Check whether there is air leakage at
all connection parts of pipes.
● Push the top rod of T-branch valve by
hexagon wrench to expel air.
● Repeat the third and fifth steps.
● Open the stop and T-branch valve with
a hexagon wrench to make the unit
operate.
● There is no leakage allowed, please
check all the piping connection parts.
You must test the leakage, generally,
it can be tested by soap water.
● discharge air and moisture
remaining in the refrigerant system with a vacuum pump.
(For method of using a manifold valve, refer to its operation manual.)
1.completely tighten the flare nuts, A, B, C, D, connect the manifold valve charge
hose to a charge port of the low-pressure valve on the gas pipe side.
2.Connect the charge hose connection to the vacuum pump.
3.Fully open the handle Lo of the manifold valve.
4.Operate the vacuum pump to evacuate. After starting evacuation, slightly loose
the flare mut of the Lo valve on the gas pipe side and check that the air is entering
(Operation noise of the vacuum pump changes and a compound meter indicates
0 instead of minus.)
5.After the evacuation is complete, fully
close the handle Lo of the manifold valve
and stop the operation of the vacuum
pump. Make evacuation for 15 minutes or
more and check that compound meter
5
indicates -76cmHg(-1×10Pa).
6.turn the stem of the packed valve B about
45 counterclockwise for 6~7 seconds
after the gas coming out, then tighten the
flare nut again. Make suer the pressure
display in the pressure indicator is a little
higher than the atmosphere pressure.
7.Remove the charge hose from the Low
pressure charge hose.
8.Fully open the packed valve stems B
and A.
9.Securely tighten the cap of the packed
valve.
If the A/C is filled with R410a, make sure to
Outdoor unit
To indoor unit
Liquid side
Gas side
Stop valve(open)
Cover
T-branch valve(open)
Hexagon wrench
Auxiliary cover
Vapor side
A
B
C
D
Packed valve Half union
Refrigerant
Outdoor
unit
Indoor
unit
Gas side
Liquid side
Manifold valve
Compound meter Pressure gauge
-76cmHg
Handle Lo
Charge hose
Low pressure valve
Vacuum pump
Charge hose
Handle Hi
To power
- 15 -

Note:
Explanation for the power cord without
plug (see below figure):
Brown= Live wire
Blue= Zero line
Yellow/Green= Grounded wire
Wiring diagram of constant speed
●
●
● The grounded wire connection:
1.loosen the grounded screw of electrical shelf.
2.Connect the grounded wire with the grounded screw
then setscrew in the mark formerly.
●
●
Unscrew the screw, take off the control panel cover from the unit.
Connect the cable to their terminals according to their number.
" "
Fix the cable to the terminal board with
fastening piece.
Reinstall the cover with the screw.
NOTE:
※
※
※
※
※
Don't reverse the power polarity.
The wrong connection lead to the mal
function of some electrical parts.
Must fix the screwnail of the firmly wire,
then drag the wire lightly, confirmation
whether it's firmly.
Must changed if the wire slide, the self-drive
screw can't used to the electric connection.
If there is a connector, connect it directly.
Heat pump Type
Cold wind Type
Connection plug
Connection plug
Connection plug
Outdoor unit terminal block
L N S V F
Yellow/green
To power
To indoor unit
Yellow/green
Brown
Blue
L N S V F
L N S V F
Yellow/green
To power
To indoor unit
Yellow/green
Brown
Blue
L N S
To power
The connection of 24000Btu、
30000Btu and 36000Btu.
V F C N
To indoor unit To power
The connection
of 18000Btu.
Cover
12L
N
More than 5mm
To indoor Unit
To power
1
2(N)
L N
Yellow
green
Heat pump Type
L N N1 CL1
Yellow/green
To power To indoor unit
Yellow/green
Brown
Blue Red
L N 2 31
Yellow/green
To power To indoor unit
Red
2 31
Yellow/green
Brown
Electrical connection
Wiring diagram of variable speed
Connection plug
NOTE:
This manual is usually includes the wiring mode for the different kind A/C. We cannot
exclude the possibility that some special type of wiring diagrams are not included .
please refer to the detailed wiring diagram which is adhered on the back of the panel
of indoor unit and E-parts cover of outdoor unit when wiring.
Note：
earthing wire should be
connected to electronic
part box (sheet metal).
Reference to photo.
Grounded wire
Earthing point
- 16 -
To indoor unit
L1 L2 S
To power
L1 S
L2

● Make sure that pipes and wires are connected.
● Make sure that liquid side valve and air side valve
both are completely open.
1. The connection of power source
● Connect the wire to independent power source socket.
● Preparation of remote controller.
● Run the air-conditioner in cooling operation mode
for 30 minutes or longer.
2. Performance evaluation
● Test the out and in air temperature.
● Make sure whether the outlet air temperature subtract from inlet s gives more
than 10° C.
Test running
Discharged air
Packing list
● Please check the following attach carefully, if part attach isn t useful, please take
care of it.
Packing list of the indoor unit
Packing list of the outdoor unit
NO. Name Unit Quantity
1
2
3
4
5
Indoor unit
Remote controller
Instructions
Batteries
Drain pipe
Set
PC
PC
PC
PC
1
1
1
2
1
NO. Name Unit Quantity
1
2
3
4
5
Outdoor unit
Connection pipe
Plastic strap
Pipe protection ring
Luting (putty)
Set
PC
ROLL
PC
PACKET
1
2
1
1
1
- 17 -

Tel: [phone] Fax [phone]
www.klimaire.com [email protected]
2190 NW 89 Place, Doral, FL 33172 - USA
The Klimaire logo is a registered Trademark of Klimaire Products inc.
Copyright 2014 Klimaire Products Inc.
The design and specifications are subject to change without prior notice for product
improvement. Consult with the sales agency or manufacturer for details.