Klimaire Ksib User manual

ULTIMATE COOLING & HEATING SOLUTION
ULTIMATE COOLING & HEATING SOLUTION
TECHNOLOGY
OWNER´S MANUAL
INSTALLATION AND OPERATION
INSTRUCTION MANUAL

CONTENTS
19
18
10
9
8
5
4
2
17
15
12
11
10
1
Name and Function of Parts
Instructions to end users
Models&specifications
Remote controller operation procedure
Operation instructions guide
Installation procedures
Electrical wiring
Grounding requirements
Installation clearance requirements
Installation of the indoor unit
Installation of the outdoor unit
Test check after installation
Maintenance and service procedures
Trouble shooting
Operation instructions
Installations
Maintenance
And service
Procedures

1
OPERATION INSTRUCTIONS
Window
receiver
i
Name and function of parts
Installation and operation installations manual
controller
Panel
Power/Run Selection

Instructions to end users
2
OPERATION INSTRUCTIONS
ower supply when the Air
conditioner is not being u-
Be sure to cut off the p-
sed for a long time.
grounding must be
If not ,please ask the qualified
to the special device.
wire should be connected
connected!The grounding
Grounding:The
drainage pipe or any other
wire to the gas pipe,water pipe,
ore,don't connect grounding
personnel to install.Furtherm-
improper places.
should contact our company
an electric shock or fire,so you
The wrong repair will lead to
ician for any repairs.
dealer or an authorized techn-
to cold air for a long time.
Don't expose the body any
conditions
from the units more than
or flammable sprays away
Keep combustible or
3 feet.

3
OPERATION INSTRUCTION
The power cord of this air con-
ditioner adopt Y-type connecti-
on,please donÿt cut off or da-
trol.If the supply cord is its ser-
vice agent or similarly qualified
magethe power cords and con-
ard.
persons inorder to avoid a haz-
Please note whether or
serious injury or harm.
collapse of the unit and cause
If it's damaged,it may lead to the
stand is firmed enough.
not the condensing unit
electricity.
It can prevent wasting excess
louvers to an upward/downward
Splashing water onto the air
operated at a continuous
will
and
the
damage
refrigerating

CANCEL
Note:
Be sure that there is on obstruction.
Don't drop or throw the remote control.
Don't place the remote control in a location exposed to direct sunlight.
Whe the unit is restarted after stopped,it can automatically resume its most latest
running mode,and the outdoor unit will Re-start subsequently
Name and Function-Remote controller operation procedure
FAN SPEED Buttonn
TEMP Setting Button:
Under the COOL, DRY, FAN
or HEAT mode, press these
two buttons could set the
temperature, the temp. setting
range is ćć, the temp.
can be memorized under each
modes.
Under COOL, DRY, HEAT
mode, press the button once to
start the SLEEP function, when
pressing once more, to switch
off the function.
When the unit turned on, under the
AUTO, COOL, FAN, HEAT mode,
press this button, to select
Auto fan, Low fan, Middle fan,
High fan, at DRY mode, the
fan speed is Low fan speed.
The FAN SPEED can be
memorized under various
modes
Press this button,
the AUTO, COOL, DRY,
FAN or HEAT mode could be
selected.
When pressing this button once,
the CLOCK icon will flash, then
the time could be adjusted.
At CLOCK adjustment, press
the TIME+ once, the ones place
on the minute will be increased
1, and continuously press 1sec
above, the tens place on the
minute will be increased 1 in
every half second. When pressing
the TIME-, the ones place on the
minute will be decreased 1, and
continuously press 1sec above,
the tens place will be decreased
1 in every half second. After adjusted
please press the CLOCK button
again for confirming.
5
OPERATION INSTRUCTION
SLEEP Button
Operation MODE Button
Clock Button

Note:
This type of remote controller is our latest model .Some buttons of the controller
which have extra function will be described below.
Name and Function-Remote controller operation procedure
Liquid crystal display(LCD)
It shows all settings
ON/OFF Buttonutton
T-OFF Buttonutton
T-ON Buttonutton
SWINGG Buttonutton
TIME+ TIME- Button CANCEL Buttonutton
Function instruction please
refer to T-ON button, T-OFF
button, CLOCK button.
Press this button once to cancel
all TIMER settings.
On, press this button
once to start the SWING function,
when press the button once again
will stop.
Press this button once will enter
into T-OFF setting, the icon of
T-OFF will flash, the T-OFF button
is available in ON or OFF mode,
the setting method is the same
with T-ON.
Press this button,
To turn the machine on or
off.
When pressing this button
once, enter into T-ON setting,
the icon of T-ON flash, every
press of TIME+, the time of
T-ON will be increased 1min.
When continuously press 1sec
above,the tens place on minute
will be increased 1, every press
of TIME- will be decreased 1
minute, when continuously
press 1sec above, the tens place
on minute will be decrease 1 in
every half second, and it goes
round with 12hours.
6
OPERATION INSTRUCTION

Don't confuse the new and worn out or different batteries.
Remove batteries when not in use for a longtime.
The batteries can be used for about one year.
The remote control should be placed away from television or audio device.
How to insert batteries
1.Remove the cover from the back of the remote control.
2.Insert the two batteries(Two AAA dry-cell batteries).
3.Re-attach the cover.
NOTE:
7
OPERATION INSTRUCTION

Operation instructions guide
8
OPERATION INSTRUCTION
repressing it.
the
the
mode

Installation location
Installation procedures
Indoor Unit
Outdoor unit
9. Do not use the unit in the immediate surrpundings of a laundry ,a bath ,a shower
or a swimming pool.
10. The plug should be accessible after the appliance is positioned.
2.3
9
OPERATION INSTRUCTION
obstructed airflow areas
e be drained

Electric wiring
Grounding requirement
10
INSTALLTION INSTRUCTION

Installation clearance requirements
11
INSTALLATION INSTRUCTION

Install of the indoor unit
Electric wiring
Install the connection pipes
Install the drainage hose
Install the piping hole
Install the rear panel
12
INSTALLATION INSTRUCTION

Connect the Neutral wire of the power connection cables to the ĀN (1)āterminal of the term-
inal board, connect the Signal wire to the “2”terminal, and connect the live wire to the“3”term-
inal and connect the earthing wire to the “ ” terminal.
13
Close
INSTALLATION INSTRUCTION

Install of the indoor unit
14
INSTALLATION INSTRUCTION

Install the outdoor unit
Install the connection pipe
Electric wiring connection
15
Connecting Block
for Indoor Unit
Coo/Heat
Model
Diagram
Power
Connection
Cable
Connecting Block
for Outdoor Unit
Signal Control Cable
(Only for Heating and
Cooling Type Unit)
Power
Connection
Cable
securely tightened.
INSTALLATION INSTRUCTION

Air purging and leakage test
16
INSTALLATION INSTRUCTION

Test operation and check after installation
Test operation
Check after installation
17
secured firmly?
Is the unit piping properly insulated?
Has the unit been connected to a secure grounding connection?
machine
machine.
short circuiting.
decrease in
INSTALLATION INSTRUCTION

Maintenance and service procedures
Clean the front panel ( When cleaning the front panel do not take it off)
When the indoor unit front panel is dirty, please use the cloth which is soaked in the warm water
under 40 ņ-then dry it and wipe the dirty places.
NOTE:
There are microcomputer components and circuit board on the displayer of the indoor unit front
panel, never let it dip in the water.
18
accumulates excessively near
more frequently.
INSTALLATION INSTRUCTION

19
MAINTENANCE AND SERVICE PROCEDURES
Be sure that objects do not obstruct the air
connected or not.
Check that whether grounding wire is properly
outlet and intake vents.
location to prevent it from spreading.
Repaint the rusted areas on the outdoor unit
has
for
as a safety feature.