Klipsch IC - SW - 8 T 2 User manual

IC-SW-8T2 IN-CEILING SUBWOOFER
OWNER’SMANUAL AND WARRANTY

3. To install the tilebridge, fold the rail side of the ring back
upon itself using the spring tensioner on the reinforcement ring
to allow insertion into the cutout hole. Once it is inserted into
the cutout hole, release the reinforcement ring such that it
unfolds back to its normal position. Position tilebridge over
cutout hole.
4. The wiring compartment is intended as a termination point
for the audio circuit. Access to this compartment is gained by
removing the terminal cover located on the back of the
speaker. The terminal cover will accept the appropriate
conduit/wire adapter (provided). Feed wires through
conduit/wire adapter and connect to the input terminal
according to the desired operation mode. Be sure to observe
proper polarity. Replace the terminal cover and tighten the
conduit/wire adapter to secure the wire.
Caution: When connecting 70V or 100V distributed
line systems, take care to ensure proper terminal
connection. Connection to the low impedance termi-
nal could result in speaker damage, amplifier
damage, or both.
Thank you for purchasing your
Klipsch IC-SW-8T2 in-ceiling subwoofer.
The IC-SW-8T2 in-ceiling speaker is designed for music reinforce-
ment applications. Unobtrusive, these loudspeakers are engi-
neered for easy, versatile installation.
The IC-SW-8T2 features a transformer-less design for 70.7V/100V
distributed-line systems. Some of the benefits of this design are:
Elimintation of transformer saturation at high output levels,
elimination of transformer insertion losses, improved bandwidth
(particularly at low frequencies), and improves power transfer to
the loudspeaker at low frequencies. For applications where 4
ohm mono or 8 ohm stereo operation is required, the mode of
operation can be selected by using an optional connection
located on the back input terminal and by properly setting the
rotary switch located under the grill.
Before installing your speakers take a moment to check the
contents of the cartons and make sure nothing has been
damaged in transit.
Contents Description QUANTITY
Speaker Module 1
Grille 1
Reinforcement Ring 1
Rails 2
Cardboard Cutout Template and Paint Mask 1
Screws (Attach Rails to Reinforcement Ring) 2
3/8" Adapter Fittings 1
1/2" Adapter Fittings 1
Installation Guidelines
The IC-SW-8T2 includes a tilebridge for use when installing
the loudspeaker into suspended ceilings or wherever additional
reinforcement of the ceiling material is required. The tilebridge
and loudspeaker are designed such that installation may be
accomplished where access above the ceiling is not possible
or may be difficult.
Installation
1. The tilebridge is composed of three parts—a reinforcement ring
and two rails. The two rails should be attached to the
reinforcement ring using the two included screws as shown below.
Caution: Be sure to comply with any and all building codes
in your area.
2. To install your IC-SW-8T2 cut out a hole in the ceiling using
either the cardboard cutout template provided with your speak-
ers or consult the measurements below. Pull wiring through hole.
IC-SW-8T2
IC-SW-8T2 12.5 "Round

5. Insert the speaker into the cutout hole. With a #2 Phillips screw-
driver, tighten the four dog clamps until they are seated securely
against the ceiling surface. Do not overtighten.
6. For installations using 70v/100v input connection, set the
switch on the front panel to "70V/100V".
For low impedance, stereo applications, the switch should be
set to 8 ohms stereo.
For low impedance, mono applications, the switch should be
set to 4 ohm mono.
In all cases, please make sure the speaker wires are connect-
ed to the appropriate terminal on the back.
7. Using the flat of your hand, insert grille into speaker frame
making sure it is securely seated and flush.
Seismic Tab
A seismic tab, located on the back of the speaker, is used
as a secondary security point. Some construction codes may
require its use. To utilize the seismic tab, run a support wire
from a secure point in the ceiling and attach it to the tab.
Be sure to consult the construction codes in your area.
Klipsch recommends the use of this tab in all installations as
a secondary means of support.
70V
60W
60W
120W
30W
100V
IC-SW-8T2 tap selectable

IN-CEILING SUBWOOFER
IC-SW-8T2 SPECIFICATIONS
IC-SW-8T2
©2003 Klipsch Audio Technologies All Rights Reserved
Specifications Subject to Engineering Changes
FREQUENCY RESPONSE 50-130 Hz +/- 4 dB
CONT. POWER HAND. 150 watts (27 V)
CALC MAX CONT. OUTPUT @ 1M 111 dB
SENSITIVITY 2.83 V/1M 92 dB
COVERAGE N/A
DI N/A
Q N/A
NOMINAL IMPEDANCE 6 ohms, min 4.9 ohms, switch set to mono or stereo position
DIAMETER 14.125"
CUTOUT DIAMETER 14.25"
OVERALL DEPTH 13.625"
MOUNTING DEPTH 13.313"
WEIGHT 23 lbs.
INPUT CONNECTORS Terminal Strip
TRANSFORMER TAPS 70V: 60W, 30W 100V: 120W, 60W
FINISHES White
TRANSDUCERS 8" Woofer AND 8' Drone
ENCLOSURE TUNING Bandpass via an 8" Drone

Klipsch Limited Warranty
KLIPSCH, AUDIO TECHNOLOGIES ("KLIPSCH")
warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below) for a period of five (5)
years from the date of purchase. During the Warranty period, KLIPSCH will repair or replace (at KLIPSCH’s option) this product or any
defective parts (excluding electronics and amplifiers). For products that have electronics or amplifiers, the Warranty on those parts is for a
period of two (2) years from the date of purchase.
To obtain Warranty service, please contact the KLIPSCH authorized dealer from which you purchased this product. If your dealer is not
equipped to perform the repair of your KLIPSCH product, it can be returned, freight paid, to KLIPSCH for repair. Please call KLIPSCH at
1-800-KLIPSCH for instructions. You will need to ship this product in either its original packaging or packaging affording an equal degree
of protection.
Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that this product is within the Warranty period, must
be presented or included to obtain Warranty service.
This Warranty is invalid if (a) the factory-applied serial number has been altered or removed from this product or (b) this product was not
purchased from a KLIPSCH authorized dealer. You may call 1-800-KLIPSCH to confirm that you have an unaltered serial number and/or you
purchased from a KLIPSCH authorized dealer.
This Warranty does not cover cosmetic damage or damage due to misuse, abuse, negligence, acts of God, accident, commercial use or
modification of, or to any part of, the product. This Warranty does not cover damage due to improper operation, maintenance or installa-
tion, or attempted repair by anyone other than KLIPSCH or a KLIPSCH dealer which is authorized to do KLIPSCH warranty work. Any unau-
thorized repairs will void this Warranty. This Warranty does not cover product sold AS IS or WITH ALL FAULTS.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. KLIPSCH SHALL NOT BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.
EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions
may not apply to you. This Warranty gives you specific legal rights, and you may have other rights, which vary from state to state.

3502 Woodview Trace, Suite 200
Indianapolis, Indiana 46268 USA
1.800.KLIPSCH •www.klipsch.com
193152
1003