KlisLite 40IR-OSD User manual

with OSD MENU
(On-Screen Display)
OPERATION MANUAL
For Box camera, Dome camera & Waterproof IR camera
(OSD Menu Optional)
Thanks for purchasing our product, before operating the unit, please read the
instructions carefully and keep this manual for future reference.
KLIS Lite COLOR CAMERA

Table of Contents
■Features
1. Features------------------------------------------------------------ 1
2. Cautions ----------------------------------------------------------- 2
3. Configurations---------------------------------------------------- 3
4. Menu Contents--------------------------------------------------- 5
5. Settings------------------------------------------------------------- 6
6. Specifications----------------------------------------------------- 16
Horizontal Resolution 450/520 TV Lines
Clear image quality has been achieved by
employing a SONY CCD, which provides a
horizontal resolution of 450 or 520 TV lines.
OSD Menu
The camera can be controlled by the On-
Screen Display Menu
Privacy Function
Unique Privacy function, the privacy function
can conceal up to 4 areas where you do not
wish to appear on the screen.
Motion Detection
Unique Motion Detection function, this function
allows you to detect the motions in the selected
area, when any motion is detected, the
selected area will alarm by flickering on the
screen.
DNR (Digital Noise Reduction)
The amount of low illuminance noise has been
significantly reduced, and the signal-to-noise
ratio (S/N ratio) as well as horizontal resolution
have been improved, resulting in a clear and
sharp image even in the dark.
Manual adjust the electronic shutter
User can manually adjust the electronic shutter
between 1/50(60)~1/100,000(120,000) second.
Day & Night Switch
The camera has a function of Day/Night
Method, it provides Color image in full light
condition (Day) and provides B/W image in low
light condition (Night) to reach the best effect.
Additional Functions
The camera has Mirror function as well as
manually adjusting picture quality function
(Such as Contrast/Sharpness/Color etc.).

Cautions
1. Before installing and operating the unit, please read the manual carefully.
2. Precision components are contained in the camera, so please avoid violent vibration during the
course of transit, maintenance and installation. For the sake of safety, please do not connect to
power before installation completion.
3. Please abide by all the electric codes when using the unit.
4. Do not use corrosive or abrasive detergent for cleaning. Use lens paper or cotton stick with
alcohol to clean the sensor board.
5. Under no circumstances to direct the camera to the sunlight or strong light sources, in order to
avoid any damage to the lens and sensor.
6. Do not use the camera in situations beyond the rated operating temperature (-10~50ºC),
humidity (less than 85%) or power source.
7. In times of malfunction, do not attempt to dismantle and service the camera by yourself .
Please refer to qualified serving personnel to repair or contact our technical department to solve
the problems.
Notice:
Please make sure that the power satisfies the normal specification before connecting
the camera.

Configurations 1--Box Camera
Figure 1: Rear panel of box camera
1. Video Out: Composite video signal output
2. PL: Power indicator
3. Power input (DC 12V, please use regulated DC12V power supply.)
DC12V:connect Positive(+) and Negative(-) polar to the corresponding power terminals.
4. Auto Iris Connector (on the side)
5. DC and Video Drive Auto Iris Lens select switch.
Select the correct position of switch to match the Auto Iris Lens on the camera.
6. Button: Press these buttons to enter and adjust the menu.
7. LEVEL: Adjust Basic level for DC drive Lens
Auto Iris Connector
Figure 2: Auto iris Connector Jack
Pin Video Drive DC Drive
1 Power Damp-
2 Null Damp+
3 Video signal Drive+
4 Ground Drive-

Configurations 2--Dome Camera
Remove the dome cover first, the setting buttons are on the back panel of the camera
module.
Figure 3: Setting buttons of Dome camera
Configurations 3--Waterproof IR Camera
Remove the rear cover of the camera with anti-clockwise, the setting buttons will appear,
the rest of two screws are for adjusting zoom and focus of the varifocal lens inside.
Figure 4: Setting buttons of Waterproof IR camera

Menu Contents
SETUP MENU
LENS MANUAL
VIDEO
DC
SHUTTER AUTO
FLK
FIXED
MANUAL
BLC ON
OFF
AGC ON
OFF
WHITE BAL. ATW
AWB
FIXED
MANUAL
FUNCTION CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
ADJUST CONTRAST (0~255)
SHARPNESS (0~31)
CB_GAIN (0~255)
CR_GAIN (0~255)
EXIT

Settings
Settings can be made by the 5 buttons ENTER/UP/DOWN/LEFT/RIGHT.
1. Press the Enter button, the SETUP menu will display on the monitor.
2. Select a menu item from the list available by the UP or DOWN button.
3. Press the LEFT or RIGHT button to change mode.
* When the LEFT or RIGHT button is pressed, available values and modes will be displayed.
Please keep pressing the button until you get to the right mode.
4. Select 'EXIT' and then press the ENTER button to finish the setting.

1. LENS
This function is used to adjust the brightness of the screen.
1. When the SETUP menu is displayed on the screen, select 'LENS' by the UP or DOWN button.
2. Select the type of the lens setting by pressing the LEFT or RIGHT button.
MANUAL:When use Manual iris lens for the camera, please select
MANUAL.
DC: When use DC drive auto iris lens for the camera, please select DC.
VIDEO: When use Video drive auto iris lens for the camera, please select VIDEO.
DC LENS OPERATION
2. SHUTTER (Condition and Speed Control)
Auto or manual control can be selected.
1. When the SETUP menu is on the screen, select 'SHUTTER' by the UP or DOWN button.
2. Select the shutter mode by pressing the LEFT or RIGHT button.
AUTO: Auto control of the shutter speed is enabled. The shutter speed is controlled
automatically according to the brightness of the scene.
FIXED: Select fixed shutter speed from 1/50, 1/250,1/500,1/2000,1/5000,1/10,000, 1/100,000.
FLK: Select 'FLK' mode when flickering occurs on the screen due to an imbalance between
NOTICE:
• When using an auto iris lens on the box camera, please select the correct Auto iris lens selection
switch on the back of the camera (See No.5 in Figure 1), please select DC or VIDEO to match DC
drive or Video drive lens on the camera.
• For dome camera, the default is DC drive lens.
• The brightness of the screen can be adjusted in DC mode. The brightness can be adjusted within
the range of 0~255. The optimum level of brightness for the user can be achieved by adjustment.

illumination and frequency. PAL Model:1/100, NTSC Model: 1/120.
MANUAL: The shutter speed can be controlled manually.
3. Choose RETURN and press the ENTER button when the settings are completed.
3. BLC (Backlight Compensation)
When there is a strong backlight behind the object, clear images of the background as well as the
object can still be obtained by using the BACKLIGHT function.
1. Select 'BACKLIGHT' on the SETUP menu by the UP or DOWN button.
2. Select the value required by pressing the LEFT or RIGHT button.
OFF: BLC function is disabled.
ON: If select BLC ON, you can manually set BLC on part of the image or the whole image.
Select BLC AREA and press ENTER to enter Area setting, choose the area where you want to
set BLC manually and press ENTER to confirm the area (Once ENTER is pressed, the color of
the choosing area will change), repeat this step to choose the other areas. After finishing setting
the area, press ENTER button for 1second to the below menus:
1) ALL CLEAR: Clear all of the BLC setting.
2) ALL SET: Manually set BLC for the whole image
3) RETURN: Press RETURN back to the area setting.
4) EXIT: Return to the BLC RATIO menu after the area is set, menu, manually adjust
BLC Ratio from 0-63 grade.

4. AGC (Auto Gain Control)
1. Select 'AGC' on the SETUP menu by the UP or DOWN button.
2. AGC OFF: Turn off the AGC function.
3. AGC ON: Select the value required by pressing the LEFT or RIGHT button. The level of gain
increase makes the picture brighter but the level of noise will also increase.
Adjust the AGC Gain Grade from 0~255
5. WHITE BAL. (White Balance)
1. Select 'WHITE BAL' on the SETUP menu by the UP or DOWN button.
2. Select the required mode by the LEFT or RIGHT button.

※Select one of the 4 modes below:
1) ATW(Auto Tracking White Balance) : This mode can be used within the color temperature
range 1,800°K ~ 10,500°K (eg, fluorescent light, outdoor, sodium vapour lamp etc.)
2) MANUAL: The manual adjustment mode enables advanced adjustment. Select ATW or AWC
first, change to manual adjustment mode and press the SET button. Set the appropriate color
temperature, increase / decrease the red and blue color values and monitor the color
changes of the object.
3) FIXED: Select Fixed AWB mode From Mode 1 – Mode 4 to match the special condition
where the camera located.
4) AWB Auto White Balance.
• Under the following conditions the WHITE BALANCE function may not operate properly.
In such cases, please select the AWB mode:
①Conditions under a very high color temperature (eg, a clear sky and sunset)
②Dark conditions.
③If the camera directly faces a fluorescent light or is installed in a place with considerable changes in
illumination, the WHITE BALANCE function may become unstable

FUNCTION
6. FUNCTION
1. Select 'FUNCTION' on the SETUP menu by the UP or DOWN button.
2. Select the mode required by the LEFT or RIGHT button.
(1) CAMERA ID
Notice: If 'CAMERA ID OFF' is selected, the ID does not appear on the monitor.
1) Select ‘CAMERA ID’ by the UP or DOWN button.
2) Select 'ON' by the LEFT or RIGHT button.
3) Press the ENTER button.

a) ID SETUP Up to 15 characters can be used for the camera ID.
①Select the character required by the UP and DOWN button, press UP/DOWN button
continuously until the correct character (A~Z, a~z, 0~9 or punctuations) appears.
②When the required character appears, press RIGHT button to the next position.
③If you want to revise a character, move the cursor to the required position by RIGHT or LEFT
button.
④Repeat the above steps until the ID is complete.
b) POSITION When the camera ID is complete, select a position to display the ID on the
monitor by UP/DOWN/LEFT/RIGHT buttons..
(2) MIRROR
MIRROR ON: Set a horizontal image reversion.
MIRROR OFF: Cancel the horizontal image reversion.
(3) DAY NIGHT

1) AUTO: Auto switch color mode to B/W under low illumination,
Set the delay time, start level and end level by the below menu:
2) COLOR: Shows full color image all the time.
3) B/W: Shows B/W image all the time.
-BURST OFF Remove Color signal in B/W Mode, raise sensitivity in B/W mode.
-BURST ON B/W Mode with Color signal.
(4) MOTION
This product allows you to observe movements of objects in different areas on the screen, the
words 'MOTION DETECTED' will appear on the screen when movement is detected, and the
motion detection area will flicker on the screen.
Please press the SET button.
1) AREA Select AREA and press ENTER to enter Motion Area setting, choose the area where
you want to set Motion Detection, press ENTER to confirm the area (Once ENTER is
pressed, the color of the choosing area will change), repeat this step to choose the other
areas. After finishing setting the area, press ENTER button for 1second to the below menu.

2) ALL CLEAR: Clear all of the Motion detection settings.
3) ALL SET: Set Motion detection for the whole area of the image.
4) RETURN: Press RETURN back to the area setting, repeat step 1).
5) EXIT: Return to the previous menu after the area is set.
2) MOTION TH Setting the motion sensitivity from 0~255 grade.
3) MOTION TRACE
MOTION TRACE OFF: Stop to track the motion on the selected area.
MOTION TRACE ON: Start to track the motion on the selected area.
(5) PRIVACY
This mode conceals the areas where you do not wish to appear on the screen.
- OFF: PRIVACY mode is disabled.
- ON: PRIVACY mode is enabled.
Select PRIVACY ON and press the ENTER button to enter PRIVACY setting:
1) AREA SEL: You can set 4 privacy areas on the screen (From Area 0 to area 3).Set dimension

of each privacy area by LEFT,RIGHT,TOP and BOTTOM menus below AREA STATE.
2) AREA STATE: Once area 0-3 is set, select AREA STATE ON to conceal the area on the
screen, select AREA STATE OFF to disable privacy function on the screen.
3) LEFT/RIGHT/TOP/BOTTOM: Set the dimension of each privacy area (area 0-3) by the slider.
4) COLOR: Select the color of each privacy area by the slider.
5) RETRUN: Return to the previous menu.
(6) GAMMA
1) Select ‘GAMMA’ by the UP or DOWN button.
2) Setting the value of GAMMA from 0.05-1.
(7) LANGUAGE
1) Select ‘LANGUAE’ by UP or DOWN button.
2) Setting LANGUAGE from “English/Japanese/Chinese Simple/Chinese Big5/Korean” by
LEFT or RIGHT button.
(8) RESET
-YES: Return to the camera’s initial setting in factory.
-NO: Keep current setting.
7. ADJUST

Adjust Contrast/sharpness/CB-GAIN and CR_GAIN manually.
CONTRAST: Increase or Decrease Contrast of the picture by the contrast slider.
SHARPNESS: Increase or Decrease Sharpness of the picture by the Sharpness slider.
CB_GAIN: Increase or Decrease the blue color of the picture by the CB_GAIN slider.
CR_GAIN: Increase or Decrease the red color of the picture by the CR_GAIN slider.
8. EXIT
Save all the setting menus and exit the main menu.
■Specifications of Box Camera
Model KLISLITE 45CH-OSD
Image sensor 1/3” SONY CCD
Video signal System NTSC/PAL
Sync System Internal Sync
Horizontal Resolution 550 TV Line
S/N Ratio ≥48dB
Minimum Illumination 0.1Lux/F1.2（low illumination mode）
Control Method
OSD (On-Screen Display) function control
(Can select without OSD)
Privacy Zone 4 Zone
Motion detect 64 Zone
Picture adjusting Brightness/Sharpness/Saturation
Gamma 0.05-1

* Specifications are subject to change without notice.
■Specifications of Dome Camera
Day/Night Switch Color/ Black &White
White Balance ATW/AWB/Fixed/Manual
BLC 8 zone
Electronic Shutter Auto/FLK/Fixed/Manual
Mirror Function ON/OFF
Power Requirement DC12V；
Current Consumption 70mA
Lens mount C/CS Mount
Operating Environment -20ºCto50ºCwithin85%RH
Model KLISLITE 90HD-OSD
Image sensor 1/3” SONY CCD
Video signal System NTSC/PAL
Sync System Internal Sync
Horizontal Resolution 550 TV Line
S/N Ratio ≥48dB
Minimum Illumination 0.1Lux/F1.2（low illumination mode）
Control Method
OSD (On-Screen Display) function control
(Can select without OSD)
Privacy Zone 4 Zone
Motion detect 64 Zone
Picture adjusting Sharpness/Saturation/Brightness
Gamma 0.05-1

* Specifications are subject to change without notice.
■Specifications of Waterproof IR Camera
Day/Night Switch Color/ Black &White
White Balance ATW/AWB/Fixed/Manual
BLC 12 zone
Electronic Shutter Auto/FLK/Fixed/Manual
Mirror Function ON/OFF
Power Requirement DC 12V；
Current Consumption 70mA
Lens 3.6mm
Manual Iris
Operating Environment -20ºCto50ºCwithin85%RH
Model KLISLITE
40IR-OSD
KLISLITE
50IR-OSD
CAM-640IV2B
/OSD
CAM-640IV3B
/OSD
Image sensor 1/3” SONY CCD
Video signal System NTSC/PAL
Sync System Internal Sync
Horizontal Resolution 550TVLine 550TVLine
S/N Ratio ≥60dB
IR LED(QTY&Diameter) 36pcs/ф5mm 36pcs/ф8mm
IR Distance 35-40m 45-50m
Minimum Illumination 0.05 Lux at F1.2 / 0 Lux（When IR LED is turned on）
Control Method
OSD (On-Screen Display) function control
(Can select without OSD)
Privacy Zone 4 Zone

*Specifications are subject to change without notice.
Motion detect 64 Zone
Picture adjusting Contrast/Sharpness/CB_Gain/CR_Gain
Gamma 0.05-1
Day/Night Switch Color/ Black &White
White Balance ATW/AWB/Fixed/Manual
BLC 12 zone
Electronic Shutter Auto/FLK/Fixed/Manual
Mirror Function ON/OFF
Power Requirement DC12V；
Current Consumption Less than 120mA (Less than 500mA when IR LED on)
Lens Built-in 4-9mm varifocal manual iris lens
Operating Environment -20ºCto50ºCwithin85% RH