Klopp CM User manual

This product is covered by a ONE-YEAR LIMITED
FACTORY WARRANTY. Please see the “Complete
Warranty Statement” inside for details, limitations
and your responsibility under the warranty. If your
Complete Warranty Statement has been misplaced,
call or email directly to Klopp International, Inc., for
a replacement.
Operating Manual
And
Service Information
Coin Counters - Models CM, CE, CECR, KK, CMB, CEB, D2, and DE
1567 North Bend Dr
Tarpon Springs, FL 34689
Ph: 813-855-6789
Model CM
Please read these operating instructions
carefully. They are brief but very
important. Please complete the
attached warranty card and mail to
us. This will ensure you are entered
in Klopp’s company database and are
eligible for future service and conversion
information.
Model CE

Our Mission
KLOPP International, Inc has been a U.S. manufacturer of high quality, economically
priced coin handling equipment since 1931. Our superb reputation for accuracy, rugged
dependability and almost no service has been justiably earned through the test of time.
We service a wide variety of industries including, but not limited to, vending, amusement,
car wash, laundry, schools, banks, restaurant/bar and convenience stores. Our mission
is to continually improve the quality of our products and services to meet our customers’
requirements and needs.
Our primary goal is the satisfaction of our customers. We also aim to achieve sufcient
prots for the continued growth of the company and the security of its employees,
distributors and customers. To achieve these goals we continually strive to produce the
highest quality products in the industry.
ONE-YEAR LIMITED FACTORY WARRANTY
Complete Warranty Statement
KLOPP International, Inc. (manufacturer) warrants each product of its manufacture to be free from defects in material and
workmanship if properly operated and serviced according to manufacturer’s Operating Instructions.
Manufacturer’s obligation under this warranty is limited to correcting without charge for labor or material at its factory any
machine, components, or parts thereof which are returned to its factory, transportation charges prepaid, within one year from the
date of original purchase of the machine, examination of which discloses to the manufacturer’s satisfaction that the machine,
components, or parts thereof are defective.
Each machine shipped from the manufacturer’s factory contains Operating Instructions. Before shipping a machine, component,
or parts thereof to the manufacturer for warranty repair, the owner must be certain that the source of difficulty could not be
corrected by performing one or more of the procedures described in the Operating Instructions or by contacting KLOPP directly
for technical support. If manufacturer finds that the source of difficulty could have been corrected by procedures contained in
the Operating Instructions or technical support, the manufacturer reserves the right to make its regular charge for any work
performed.
This warranty does not apply to any machine, component, or part thereof which must be replaced because of normal wear and
tear or lack of maintenance, which have been subject to misuse, negligence, accident or which have been repaired or altered
outside of the manufacturer’s factory, or which contain parts not manufactured or supplied by the manufacturer. Manufacturer
is not liable for any loss, damages (including consequential damages) or expense caused from or related in anyway to the use
of its products or from any other cause. This warranty supersedes and is given in lieu of all other express or implied warranties,
including warranties of merchantability and fitness for a particular purpose. No person or entity is authorized to give or alter
any warranties on behalf of the manufacturer. Manufacturer reserves the right to make design and/or operational changes in its
products or parts thereof without obligation to incorporate these changes in products previously produced.
You can Count On KLOPP....

PLEASE READ THESE INSTRUCTIONS THOROUGHLY
BEFORE OPERATING YOUR KLOPP COUNTER:
COINS PROCESSEDA. — KLOPP Coin Counters count, wrap
and bag $1, 25¢, 10¢, 5¢, and 1¢ U.S. coins, as well as the
most popular token sizes: 1”, .984, .900, .882, and .800.
- one denomination at a time - they will not count mixed
coins. KLOPP Counters can also be converted to count the
following Canadian coins: $2, $1, 25¢, 10¢, 5¢ as well as
the 1 1/8” token. Canadian machines will not count dimes
or pennies. Models CMB and CEB count and bag “One
Coin” only, which is set at the factory. They will not wrap.
WRAPPING TUBESB. — Your KLOPP was shipped with
one of the following sets of tubes: either a set of Wrapping
Tubes including the 25¢, 10¢, and 5¢ -OR- a set of (1)
Wrapping Tube and (1) Universal Bagging Tube. Additional
tubes for wrapping include the $1 and 1¢ coins, and 1”, .984
and .900/.882 tokens (.800 tokens can be wrapped using
the 5¢ Wrapping Tube). All Wrapping Tubes, as well as the
Universal Bagging Tube, may be ordered directly from the
KLOPP factory.
CRIMPHEADSC. — The Model CECR ships with crimpheads
to crimp wrappers closed. The Model CECR1 ships with (1)
crimphead of your choice. The Model CECR4 ships with (4)
crimpheads for 25¢, 10¢, 5¢, and 1¢. Additional Crimpheads
are available for .50¢, $1, and Canadian $2.
100% INSPECTIOND. — Your KLOPPis 100% inspected at the
factoryandhas beenoperated with alldenominations ofcoins
and tokens. You should receive years of trouble-free service.
On the very remote chance that you should have a problem or
even a question, please call “KLOPP Service“ 800-356-9080.
TO OPERATE YOUR KLOPP, DO THE FOLLOWINGE. :
(For Models CMB, and CEB, see Step I)
Pour a quantity of the same coins (no mixed coins) into the1.
3-sided coin tray.
2. Turn the Denomination Selector Knob to the appropriate
setting for your coins: $, T, QT, NT, P or D. This will set the
proper height and width in the counting track for the coins
you are processing. For tokens, use the T setting for 1” and
.984 sizes, the QT setting for .900 size, and the NT setting
for .882 and .800 sizes
Canadian CM-C2 and CE-C2 Counters and the 1-1/8”
Token Counters use the Denomination Selector Settings
below. These counters will not count the Dime or Penny.
TO COUNT SETTINGS
$2 Toonie Coin & 1-1/8”/1.073 Token 1/8
$1 Loonie Coin & 1” Token $T
.984 Token ●
Quarter & .900 Token QT
Nickel & .882 Token NT
.800 Token T
3. By turning the Coin Stop Knob, coin stops can be set at 20,
25, 40 or 50. An automatically actuated coin stop blocks the
ow of coins when the desired quantity is reached. Set the
Coin Stop Knob on 40 for quarters or nickels, 50 for dimes
or pennies, or 25 for dollars. Setting the Coin Stop Knob on
C will allow a continuous ow of coins into a bag or bucket.
Total counts are recorded on a rugged, mechanical, 5-digit,
resettable meter.
Set the meter at “0”.4. (IMPORTANT — READ STEP F NOW!)
To5. COUNT AND WRAP - Hook on the proper coin wrapping
tube and insert an empty coin wrapper (READ STEP G).
OPERATING
INSTRUCTIONS
STEP
If6. manual model, push down rmly on the Coin Stop
Knob and release. Then turn the crank to start coin ow.
If electric model, turn “ON” the motor, push down rmly
on the Coin Stop Knob and release to start coin ow.
HOW TO “IN FEED” You must “in feed” the PROPER7.
quantity of coins from the large 3-sided coin tray onto
the round disc in order to get a speedy, uninterrupted
ow into a wrapper or bag. Over-lling the disc slows the
“out speed” and may cause jamming if coins are worn.
TO PROPERLY “IN FEED” Continuously
hand rake the coins from the tray onto
the disc. At all times, you should be able
to see at least a small portion of the step
in the disc as it rotates (see drawing).
Once the machine counts the number of coins you set8.
it for, the coin ow will stop. You can then remove the
lled coin wrapper and fold the open end closed. Insert
another empty coin wrapper and press down on the
Coin Stop Knob to release the next ow of coins. Repeat
as necessary until all coins are counted and wrapped.
To9. COUNT AND BAG - Replace the wrap tube with our
Universal Bagging Tube. Set the Coin Stop Knob on “C” for
continuous ow, and run the machine. Always use a Universal
Bagging Tube when bagging coins or tokens. NEVER USE
A WRAPPING TUBE TO BAG. IT WILL JAM.
To10. CRIMP WRAPPERS CLOSED (Model CECR only) -
Insert the proper coin crimphead into the black receiver on
the right-side of the machine. “Push and Twist” to ensure
crimping head is located and locked in place. Fill a “at” or
“gunshell” style wrapper with the proper amount of coins.
Press the lled coin wrapper rmly against crimphead until
the wrapper is tight and a rolled seal has been formed.
Press at a steady rate (2-3 seconds). DO NOT FORCE.
Let the crimper do the work.
F. CLEARING THE COUNTING MEMORY
— IMPORTANT INFORMATION
Before counting and wrapping EACH DENOMINATION,
it is necessary to CLEAR THE COUNTING MECHANISM
MEMORY. If you did not have the exact number of coins/
tokens on the last roll you counted, or changed the stop from
“C” continuous to a numerical stop “20, 25, 40, 50”, your
KLOPP will deliver only the “balance due” on the rst roll at
the next counting.
To CLEAR YOUR MEMORY, do the following:
Prepare to count as you normally would (See E “To1.
Operate Your KLOPP”).
Do not insert a wrapper as you normally would. Instead,2.
hold your hand under the tube.
Turn “ON” the motor or turn the crank and release the3.
ow of coins/tokens by depressing the Coin Stop Knob.
When the “balance due” from the previous count is
reached, no more coins/tokens will ow into the tube.
Return the handful of coins/tokens to the hopper.
Reset the meter to zero and insert a wrapper in the tube.4.
Depress the Coin Stop Knob and you will now receive a full5.
roll of coins/tokens.
For example, let’s say you’re counting a batch of quarters
and you’ve set your Coin Stop Knob at 40. You come to
the end of the batch, and the last group of coins is only 25
pieces. You stop, because you’re done, but the machine is
still waiting for 15 more pieces. The next time you run the
machine, no matter the setting, it will only count out those
last 15 coins/tokens, and then it will stop. You would dump
those 15 pieces back into the hopper, and reset the meter to
zero, and then proceed as normal from step E-5.

G. HOW TO USE A PAPER COIN WRAPPER IN YOUR KLOPP
WRAPPING TUBE.
Insert the paper coin wrapper UP into the nylon wrapping tube 1/3 the
length of the wrapper (A).
Grasp the bottom of the wrapper with your left thumb (B) on one side
and your middle nger (C) on the other side. At the same time, insert
your index nger (D) just slightly up into the bottom of the wrapper
so that the 1st coin will land at on the tip of nger. Be sure that the
wrapper is held in a round conguration. DO NOT PINCH IT. If the
1st coin does not land at on your nger, very quickly wiggle your
nger and it will lay at. If the rst coin lands at, all others will follow.
When the wrapper is full, the counter will automatically stop dispens-
ing coins. Grasp the wrapper rmly and slide it down and out of the
nylon wrapping tube. Fold both ends. THE PRECEDING IS ONLY AN
EXAMPLE. PLEASE USE ANY FINGER ARRANGEMENT THAT IS
COMFORTABLE FOR YOU.
NEVER insert the paper wrapper more that 1/2 its length into the tube.
If you do, the top edge of the wrapper may become bent over by falling
coins and create a jam in the wrapping tube. The small ledge you see
if you look up into the nylon tube is created by the manufacturing
process and is NOT a stop for coin wrappers. If coins continue to
jam at the top of the paper wrapper or if the wrapper does not t
reasonably smooth against the wrapping tube wall, the wrapper may
be defective. Use a different brand of paper wrapper.
TO PREVENT JAMS, YOU SHOULD NEVER USE A NYLON
WRAPPING TUBE AS A CONTINUOUS FLOW BAGGING TUBE.
OUR UNIVERSAL BAGGING TUBE, WITH A MUCH LARGER
INTERNAL DIAMETER, IS TO BE USED FOR BAGGING.
H. POSSIBLE ADJUSTMENTS
There are only three adjustments that should ever be necessary
on your KLOPP. These are: (1) Adjusting the tension on the
combination tray leg/locking arm; (2) Adjusting the space between
the lower discharge wheel and upper discharge roller; (3)
Removing a jammed coin.
Adjusting the tension on the combination tray leg/lock-1.
ing arm — Note that the tray leg is also used to lock the
coin tray in its closed position while transporting your KLOPP
from one location to another. From time to time, tension on
this locking arm may become reduced through use. To in-
crease the tension on the locking arm, note the small rub-
ber tipped support arm located on the rear inside of the coin
tray. When the tray is closed, this support arm ts against the
top of your KLOPP counter immediately in front of the meter.
To increase the tension on the tray leg/locking arm, remove
rubber tip, then grasp the arm with a large pair of pliers and
gently bend it slightly upward. To decrease the tension on
the tray leg/locking arm, bend the support arm downward.
Adjusting the space between the lower discharge wheel2.
and the upper discharge roller — Note that after leaving
the hopper, coins/tokens are moved to the tube by passing
between the lower discharge wheel and the upper discharge
roller. (Only a small portion of the lower discharge wheel
is visible where it protrudes upward in the coin track.) The
distance between the wheel and roller is set at the factory and
locked in place. The black rubber-like material which contacts
the coins/tokens is a special formula to give years of wear-
free service. No adjustments should be necessary until after
millions of coins/tokens have passed through your KLOPP.
With years of use some wear may occur on the surface of the
roller or wheel. This may cause coins not to be transported
in a perfectly even ow. If this ever occurs, do the following:
Face the front of your KLOPP and locate the small hole on
the side to your right. Turn your KLOPP upside down so that
you can see the mechanism from the bottom. Insert a small
screwdriver in the hole described above and locate the lower
discharge wheel adjustment screw head. DO NOT TURN THE
SCREW HEAD, YET. Now locate the slotted set screw which
holds the lower discharge wheel screw in position. Loosen the
set screw by turning it counter-clockwise 1/4 turn — NO MORE.
Turn you KLOPP right side up again. Set the Denomination
Selector Knob at D. Insert the screwdriver in the hole
described above. Turn the screwdriver and note that as
you do the lower discharge wheel moves slightly up and
down. Move it upward until it is the distance of one-half
the thickness of a dime from the upper discharge roller.
Turn your KLOPP upside down and retighten the set screw
by turning clockwise. Test your KLOPP for a smooth ow
of dimes. Be sure to test all denominations not just dimes.
Removing a jammed coin —3. If a mutilated or bent coin
becomes stuck in the track or under the shield, do the following:
If a coin jams, YOU MUST turn “OFF” the motor. If you do not,
you may damage the rotating disc and/or burn up the motor.
Turn the Denomination Selector Knob to “$” which will open
the height and width of the track to the maximum opening.
Remove the jammed coin by turning the crank in a reverse
direction or rotating the disc by hand on an electric counter
when the motor is shut off.
I. TO OPERATE MODELS CMB AND CEB, DO THE
FOLLOWING:
Hook on our Universal Bagging Tube and fasten a coin bag
using the ring at the bottom of the tube. Once the bag is
fastened, pour coins into the 3-sided coin tray and run machine
following the “Proper In-Feed” procedure.(See Section E, #7)
A
C
B
D

SERVICE
INFORMATION
CLEANING YOUR KLOPP — To keep your KLOPP in good
working order, it is necessary to periodically CLEAN the rotating
disc and the coin track, plus the black upper and lower discharge
rollers and the white nylon drive wheel. This can be accomplished
by the use of a soft rag moistened with rubbing alcohol. NEVER
USE WD40. CAUTION — Be careful that all solvent is dry before
turning on electric models. Also, do not allow lint or foreign matter
to build up in the coin track or around the starwheel which turns
as each coin passes it to be counted.
LUBRICATING YOUR KLOPP — Your KLOPP was lubricated at
the factory with a few drops of oil. If it ever begins to make a
squealing or grinding sound, it needs to be relubricated. To do so,
follow the directions below:
FOR MANUAL MODELS CM & D2 —1. Turn your KLOPP
upside down. Put two drops if “3-in-1” (or equal) oil on the
rotating shafts at the locations shown in Drawings A & B
below. DO NOT OVER OIL. Make sure to wipe off excess oil
with a clean cloth and alcohol prior to running coins through
the machine. Note: Drawing B is for machines built after 2004.
FOR ELECTRIC MODELS CE, CECR, KK & DE —2. Turn
your KLOPP upside down. Put two drops of “3-in-1” (or
equal) oil on the rotating shafts at the locations in Drawing
A. See drawing C. Loosen the nut 1/4 turn (11/16 wrench
needed) and then remove the hexhead bolt leaving the nut in
position on the bolt. Look through the hole in which the bolt
was located. You will see an oil retaining wadding. Put 18
drops of Waylub oil on top of the wadding. Replace the bolt
and retighten nut. Leave the counter upside down for a few
minutes so that the oil can work its was down through the
wadding and onto the shafts. DO NOT OVER OIL.
DISC INSERTS FOR ALL MODELS —3. After cleaning the
rotating disc (See “Cleaning your KLOPP”) remoisturize the
Black Disk Inserts on the rotating disc with “3-in-1” (or similar)
oil. Place 1-2 drops of oil on each insert and let absorb
overnight. Important: Do not over oil and make sure to wipe
off excess oil from the disc prior to operating your machine.
REMEMBER:
IF YOU HAVE A PROBLEM OR JUST A
QUESTION ABOUT YOUR KLOPP, CALL
KLOPP CUSTOMER SERVICE AT
800-356-9080
OIL
OIL
BOLT
NUT
OIL
DRAWING A DRAWING B
DRAWING C
REPAIRS AND REPLACEMENT PARTS — KLOPPS are very heavy
duty and almost literally “last forever”. Our one-year limited factory
warranty on both parts and labor, when returned to the factory prepaid,
undamaged and unaltered, gives full protection for 1 year from the date
of original purchase.
Eventually, some parts will probably wear. It may take 3 years or 10
years but someday it will happen. To replace a worn part you have 2
choices of action.
REPAIR SERVICE —1. Call KLOPP at 800-356-9080 for shipping
instructions - OR - visit our website at www.KloppCoin.com to
download our Service Information Sheet. This sheet provides
detailed information on our Repair Service.
NOTE: Please include a Service Data Sheet when sending in your
KLOPP machine for repair. This will ensure you have provided the
informationthat isneededtoprocessyourrepairina timelymanner.
REPLACEMENT PARTS —2. To order replacement parts, call us at
800-356-9080. We will be happy to assist you to ensure you are
ordering the proper part. Parts diagrams, photos, and descriptions
may be viewed and/or downloaded on our website at www.
KloppCoin.com. When ordering, please provide the Model and
Serial Number of your KLOPP.
WARNING
Wipe off all excess oil. Be sure oil does
not get on either the large black or white
wheels or the belt from the motor to the
pulley. To remove excess oil, wipe off
these parts with a clean cloth lightly
dampened with alcohol.

1567 North Bend Dr
Tarpon Springs, FL 34689
Ph: 813-855-6789
www.KloppCoin.com
[e-mail]