Klopp KCS Series User manual

1567 North Bend Dr
Tarpon Springs, FL 34689
TEL: [phone]
800/356-9080
www.kloppcoin.com
[email protected]
KCS Series: Coin Counting Scales Operation Guide
Basic Operation:
1. Turn machine on using power switch on left-hand side of machine. Wait for machine to go through countdown,
and for the arrow to point to "Stable" in the Total Window.
2. Press Coin Counting Key for the desired coins to be processed. There is a sticker on the right-hand side of the
machine denoting which keys correspond to which coins. The Denomination Window will show the coin you
select. For example, to process Quarters, you would press the "3" key, and the Denomination Window would read
"0.25".
3. If you are using a container or bucket to count your coins into, you must zero out the weight of the container.
Place the empty container on the scale and wait for the arrow to point to "Stable" in the Total Window. Press the
"T" button and wait for the scale to zero out.
4. Place the coins to be counted on the platter/container. Wait for the arrow to point to Stable in the Total
Window. The Quantity Window will show the total number of coins, and the Total Window will show the dollar
amount. For example, if you had placed 200 quarters on the platter/container, the Quantity Window would show
"200" and the Total Window would show "50.00".
5. Remove the coins from the platter/container and place the next batch of coins to be counted. If you are
changing to a different denomination of coins, choose the Coin Counting Key for that coin before placing the new
batch on the platter/container.
Using the Memory Function:
Saving Coin Counts:
1. Select the Coin Counting Key for coin to be counted.
2. Place coins on platter/container and wait for the arrow to point to Stable in the Total Window.
3. Press the "M+" key to save the information.
4. Remove coins from platter.
5. Select Coin Counting Key for next coin to be processed and repeat steps as needed, until counting/printing
is complete. NOTE: You must select the next Coin Counting Key even if it is the same denomination
as your last count.
Reviewing Saved Counts and Grand Total:
Press "MR" key to cycle through each saved entry. The last item displayed is the Grand Total.
Erasing Saved Counts and Grand Total:
Press "MC" key.

1567 North Bend Dr
Tarpon Springs, FL 34689
TEL: [phone]
800/356-9080
www.kloppcoin.com
[email protected]
Establishing Unit Weight for Programming Additional Coins or Tokens
Part 1: DETERMINING "UNIT WEIGHT" FOR COINS OR TOKENS
If you already know the weight of a single coin or token, in grams, then you can skip to Part 2.
1. Enter into the Weighing Mode of the scale. Press and hold both the "4" and "9" keys, and then press the "MC"
key.
2. If you are using a bag, bucket, or other type of container, place the empty container onto the scale platter. Wait
for the Stable indication. (a little arrow in the bottom right window will point to "Stable")
3. Press "T" (Tare) to zero out the weight of the container. (Perform only if a container is needed)
4. Place a large sample of pre-counted coins or tokens onto the scale platter, or into the empty container. Use as
many as possible, and make sure you know exactly how many you are using.
5. Write down the total weight displayed. (EXAMPLE: 2.259 for 400 pieces)
6. Multiply your total by 1,000 to convert to grams. (EXAMPLE: 2.259 x 1,000 = 2259)
7. Divide this number by the sample amount to get your Unit Weight. (EXAMPLE: 2259/400 = 5.647). Write
down the Unit Weight.
8. Repeat the procedure for any other coins or tokens you wish to use.
9. When you have written down all the Unit Weights you need, turn the scale off.
Part 2: INPUTTING UNIT WEIGHT FOR COINS OR TOKENS
1. Turn the Scale off, if it is on, and then remove any container or bucket.
2. Turn on the Scale and wait until the countdown is complete.
3. Press "Coin Cal", then press the "0" key 4 times, then "Coin Cal" again. These keys must be pressed within a
few seconds, or it will return to the counting mode automatically.
4. Select the key to be programmed. (the 0, 7, 8 and 9 are empty keys)
5. Press "Coin Cal", then input the new Unit Weight. (EXAMPLE: From the calculation above, you would press
"5" "6" "4" "7".) Press "Coin Cal" to Save.
6. Repeat steps 3 and 4 for any other Unit Weights you wish to enter.
7. Turn the Scale off, wait a few seconds, then turn the Scale on again. Wait for the countdown to complete.
8. Select one of the keys you just programmed and place a known amount of coins or tokens on the scale to test
the accuracy. Repeat with any other keys you may have programmed.
Please feel free to call us with any questions or concerns. 1-800-356-9080
Respectfully,
KLOPP Service Department