KMC Controls CTE-5001 User manual

CTE-5001/5011 1 Installation Guide
Installation Guide
Room Thermostats, Single Setpoint, DA Cooling or RA Heating
CTE-5001/5011
Mounting
Mounting 1
Connections and Wiring 1
Adjustments and Calibration 3
Maintenance 3
Accessories 3
Important Notices 3
NOTE: Seethedatasheetforspecications.
• Aachtheoptionaladapterbackplate(seethe
Accessoriessection)toastandard2"x4"(51x102
mm)handyboxordirectlytoahollowwall.
• Removethecoverand,usingthetwo6-20
self-threadingscrews(included),aachthe
thermostattothebackplate.
Connections and Wiring
See the basic instructions below and the diagrams
on the next page. The rst sample application on
the next page illustrates basic DA cooling. The sec-
ond sample application illustrates DA cooling with
RA heating changeover.
• Terminal A:ForDirect Action,jumperto
terminalB;orforReverse Action,connectto
terminal5oftheCEP/CSP-4xxxcontroller/
actuator.
• Terminal B:ConnecttoCEP/CSP-4xxxterminal4.
• Terminal C:ForDA,connecttoCEP/CSP-4xxx
terminal5;orforRA,jumpertothermostat
terminalB.
• Terminal D:ConnecttotheCEP/CSP-4xxxIn
terminal6.
• Terminal E: Tooverridetofullclose,connect
toCEP/CSP-4xxxterminal5;ortooverridefull
open,connecttoCEP/CSP-4xxxterminal4.
• Terminal F:Foroptionalowreadoutat
thermostattestpoints,connecttotheCEP/CSP-
4xxxOutterminal7.

CTE-5001/5011 2 Installation Guide
A B C
D E F
Optional CFM Readout on Test Points
0–6.5 VDC Cooling or Heating Output
24
VAC
–7
6
5
4
3
2
1
8
9
10
11
12
13
14
CEP-4000 Series
Controller-Actuator
(To override to full close, connect E to terminal 5,
or to override to full open, connect to terminal 4)
REE-1014
Relay Module
YX
Controller
54
Z
A
Sensor
C
0 or 6.5 VDC (Out)
Auxiliary Trigger
To Duct Temperature
Sensor (10K, Type II
or III Thermistor,
such as in an
SSE-2001/2002)
Sample Application—DA Cooling with RA Heating Changeover
NOTE: Changeover setpoint is
factory-set at 77° ±4° F
A B C
D E F
Optional CFM Readout on Test Points
Sample Application—DA Cooling
9.1 VDC Power
Common
0–6.5 VDC Cooling Output
24
VAC
–7
6
5
4
3
2
1
8
9
10
11
12
13
14
CEP-4000 Series
Controller-Actuator
(To override to full close,
connect E to terminal 5,
or to override to full open,
connect to terminal 4)

CTE-5001/5011 3 Installation Guide
Adjustments and Calibration
Thermalcalibrationisnotrequired.Minimumand
maximumcontrolpointscanbecalibratedbeforeor
aerthethermostathasbeeninstalled.
NOTE: In2009,theboardswerechanged,andthe
newpotentiometerscanonlybeadjusted
fromthefrontoftheboard(insteadoffrom
boththefrontandthebackasintheolder
boards).
Tosettheowratesandthedeadband:
1. Removethecoverbypullinguponitfromthe
boom.
2. Withavoltmeter,measurethevoltagebetween
Common(B)andOut(D).
3. AdjusttheMinimumFlow—turningthe
potentiometerclockwise(CW)increasestheow:
• ForDA,turnthesetpointdialtothehighest
(warmest)temperature,and(withasmall
Phillipsscrewdriver)adjusttheMinimum
Flow.
• ForRA,turnthesetpointdialtothelowest
(coldest)temperature,and(withasmall
Phillipsscrewdriver)adjusttheMinimum
Flow.
4. AdjusttheMaximumFlow—turningthe
potentiometerclockwise(CW)increasestheow:
• ForDA,turnthesetpointdialtothelowest
(coolest)temperature,andadjustthe
MaximumFlow.AlwaysadjustMaximum
FlowtoavaluehigherthantheMinimum
Flow—ifindoubt,turnMaximumFlow
fullyCW(increase)atthebeginningofthe
adjustment.
• ForRA,turnthesetpointdialtothehighest
(warmest)temperature,andadjustthe
MaximumFlow.AlwaysadjustMaximum
FlowtoavaluehigherthantheMinimum
Flow—ifindoubt,turnMaximumFlow
fullyCW(increase)atthebeginningofthe
adjustment.
5. Reinstallthecover.
NOTE: Ifusinga changeoverapplication,beaware
ofwhichmodethesystemisinandfollow
theappropriateprocedureforadjustingDA
orRAminimumandmaximumows.To
helpdeterminethemode,turntheMin.pot
CCWtozeroandMax.potCWtofulland
determineiftheoutputincreasesordecreas-
esasthesetpointismovedbackandforth.
© 2011 KMC Controls, Inc. 831-019-01G
KMC Controls, Inc.
19476IndustrialDrive
NewParis,IN46553
574.831.5250
www.kmccontrols.com;[email protected]
Important Notices
Thematerialinthisdocumentisforinformation
purposesonly.The contents and the product it
describes are subject to change without notice.
KMCControls,Inc.makesnorepresentationsor
warrantieswithrespecttothisdocument.Innoevent
shallKMCControls,Inc.beliableforanydamages,
directorincidental,arisingoutoforrelatedtothe
useofthisdocument.
Maintenance
Carefulinstallationwillalsoensurelong-termreli-
abilityandperformance.Removedustaccumulation
asnecessaryfromslotsintopandboom.Clean
coverwithaso,dampclothandmildsoap.
Accessories
HMO-5001 Dualtoggleboltforbackplate
mountingtodrywall
HMO-5014 Insulatingstand-o,lightalmond
HMO-5016 Insulatingstand-o,white
HMO-5036 Adapterbackplatetovertical
handybox,lightalmond
HMO-5037 Adapterbackplate,vertical,
white
HMO-5038 Adapterbackplatetohorizontal
handybox,white
HMO-5039 Adapterbackplate,horizontal,
lightalmond
HPO-0031 Setpointcover,white
HPO-0032 Setpointcover,lightalmond
REE-1014 Relaymodule,heat/coolchange-
overforCTE-5000series
SSE-2001/2002 Ductow/temperaturesensors
forVAVsystems
XEE-4002 Powersupply,24VACto9.1VDC
NOTE: Formoreaccessories,seetheThermostats
sectionoftheElectronicandPneumatic
CondensedCatalog.