Knorr-Bremse BENDIX TIM G2 User manual

User Manual
Commercial Vehicle Systems
T I M G 2 -
Trailer Information Module

Disclaimer:
The information contained in this document is intended for the exclusive use of trained persons within the commercial vehicle industry, and must not be passed on to any third party. All recommendations regarding products and their servicing or usage are with reference to
Knorr-Bremse products and should not be considered applicable to products from other manufacturers.This information does not purport to be all-inclusive and no responsibility is assumed as a result of its use.We cannot accept any liability nor oer any guarantee regarding
data accuracy, completeness or timeliness. The information does not represent any guarantee or ensured characteristics of the Products or Systems described. No liability can be accepted based on the information, its use, recommendations or advice provided. In no event
may we be held liable for any damage or loss except in the case of wilful intent or gross negligence on our part, or if any mandatory legal provisions apply. Any legal disputes arising from the use of this information shall be subject to German law.
Note: If service work is carried out on a vehicle as a result of information taken from this document, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full functional order before the vehicle is returned into service. Knorr-Bremse accepts no
liability for problems caused as a result of appropriate tests not being carried out.
This disclaimer is an English translation of a German text, which should be referred to for all legal purposes.

T I M G 2 -
Trailer Information Module

4
5
User Manual
Navigation Buttons
Moves menu cursor down. Short hold jumps down one position,
long hold jumps to end of list (Exit).
Moves menu cursor up. Short hold jumps up one position, long hold
jumps to top of list.
Selects menu item at cursor position.
Cursor Function display
Menu point has no sub menu.
Menu point contains a sub menu or an item that may be modified.
Navigation Buttons and Functionality

4
5
TIM G2 - Trailer Information Module
Ignition on - Display activates automatically, all configured
menus are available.
or
<Active Faults>
ODO: 127mi
Load Rear: 58420lb
Inst. Test Missing
DISCLAIMER
For information
only! Press any key
to continue.
SUPPLY: 11.9V 58368LB
ODO: 127MI
Bendix TIM
TABS6
Advanced
Inst. Test Missing
TPMS Info
Main Menu
Exit
or
or or
Ignition off - Display is off, push one of the navigation
buttons for one second to activate the display.
NOTE: Menu options are limited (see Menu Overview page 6-7).
or
DISCLAIMER
For information
only! Press any key
to continue
<Active Faults>
ODO: 127mi
Main Menu
Exit
or
or or
or or
BATTERY MODE
For information
only! Values are
read from memory!
Initial Menu
Initial Menu
Initial Menu
Main Menu
Stored Faults
Distance & Serv.
Operating Info
ECU Info
Main Menu
+
Stored Faults
Distance & Serv.
Operating Info
System Info
Scroll until
“Main Menu”
Behaviour with Ignition on / off
Bendix TIM
TABS6
Advanced
Scroll until “Main Menu”

6
7
User Manual
Set Next Service
Date Based
Distance Based
Exit
Info Total
ABS Events
RSP Interventions
Brake History
System Powering
Exit
Info Period
Period mi:
ABS Events:
RSP Interventions
Brake History
System Powering
Reset Period Data
Exit
Set LCD Contrast
LCD Contrast:
Save & Exit
Exit
Manufacturing Info
Part num:
K001966XXXXXX
SW:
Serial:
ManufDate:
Exit
<Active Faults>1
ODO: 0mi
Load Rear: lb
Inst. Test Missing
2
TPMS Info
3
Main Menu
Exit
Stored Faults
Distance & Serv.
Operating Info
System Info
ECU Info
TIM Info
Exit
Stored Faults
Active faults:
<none>
Inactive faults:
<none>
Clear faults
Exit
Distance & Serv.
ODO: mi
Trip: mi
Reset Trip
Srv Date:
Srv mi:
Set Next Service
Exit
Operating Info
Info Total
Info Period
Exit
ECU Info
Part num:
SW:
Exit
System Info
TPMS Setup
3
Load Info
Pressure Info
Tilt Angle:
Installation Test
Liftaxle control
Exit
TIM Info
Lang.:
Set LCD Contrast
Manufacturing Info
Exit
Initial Menu Main Menu
+
Repeat until
“Main Menu”
<Active faults>
ODO: Omi
Load Rear: lb
Inst. Test Missing
Trailer Information Module
Stored Faults
Distance & Serv.
Operating Info
System Info
Trailer Information Module
Menu Overview

6
7
TIM G2 - Trailer Information Module
Date Based
Year:
Month:
Day:
Save & Exit
Exit
Distance Based
Srv mi:
Save & Exit
Exit
RSP Intervention
Test Puls:
Step 1:
Step 2:
Step 3:
Exit
Brake History
Appl vs Dem Values
Over Pressures
Exit
System Powering
ConstPower:
Stop Lamp:
Exit
Load Info
Front Axle Group 4
Bogie Load: 4
Rear Axle Group
Bogie Load:
Exit
Over Pressures
Dem >130psi:
Res >130psi:
Exit
Appl vs Dem Values
<22psi:
22-36psi:
36-58psi:
>58psi:
Exit
Pressure Info
Dem P4:
Dem CAN:
Susp P42:
Pcyl P21:
Pcyl P22:
Pcyl P2:
Res P1:
Exit
Installation Test
Start Inst. Test
Install Check
Reserv. Press
S-A Sensor: 4
S-E Sensor: 4
S-C Sensor:
S-D Sensor:
S-F Sensor: 4
S-B Sensor: 4
Demand Press:
Tilt Angle:
Exit
Menu Overview
Liftaxle control
LC Tuning:
Save & Exit
Exit
TPMS Setup 3
Enter conf. Mode 6
Learn Sensor 5
Delete Sensor 5
Vehicle param.5
Axle param.5
Altitude comp:5
Change password 5
Leave conf. Mode 5
Exit
Enter conf. Mode 6
Password:
Match password
Exit
Vehicle param.5
SAL % CIP:
FAL % CIP:
Over Temp:
Exit
Change password 5
Password:
New passw.:
Save new passw.
Exit
(Set Next Service) (Info Total) (System Info)(Info Period)
Menupoints in green are not available in BATTERY MODE
1Displayed only if active faults are available
2Displayed only if installation test is missing
3Displayed only if Tire Pressure Monitoring System (TPMS) configuredDisplayed only if Tire Pressure Monitoring System (TPMS) configured
4Displayed only if included by vehicle ABS configuration
5Displayed only if TPMS configuration mode enteredDisplayed only if TPMS configuration mode entered
6Displayed only if TPMS configuration mode not enteredDisplayed only if TPMS configuration mode not entered

8
9
User Manual
Reset Trip
Srv Date 18-01-10
Srv Mi: 6240mi
Set Next Service
2008-03-15 19:43.44
Last detection:
0mi
2008-03-31 10:11.47
Active Faults:
S-C O/C.
S-D O/C.
Module Error
Examples:
a) Setting next service distance to 6,250 miles (mi)
Main Menu
Stored Faults
Distance & Serv.
Operating Info
System Info
+
1x
Date Based
Distance Based
Exit
Srv Mi: 0mi
Save & Exit
Exit
+
5x
+
1x
Srv Mi: 6250mi
Save & Exit
Exit
NOTE: “*” inactive, buttons and
revert to normal function
+
1x
Next service
distance has been
succesfully set in
ECU.
Indicates cursor buttons and
are now used to change ‘mi’ values
“*”
Srv Mi:*0mi
Save & Exit
Exit
2x = 6250 mi
+
END
b) Display current fault status
Main Menu
Stored Faults
Distance & Serv.
Operating Info
System Info
Overview of fault
S-C Open circuit or
Shorted to Battery
DTC:
000D00
+
1x
Fault Detail
Scroll
Occurrence count:
4
First detection:
0mi
Scroll
END

8
9
TIM G2 - Trailer Information Module
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
<Active Faults>
ODO: 127mi
Load Rear: 58420lb
Inst. Test Missing
Examples:
c) Changing the language default (English to French)
Main Menu
System Info
ECU Info
TIM Info
Exit
+
Scroll to “TIM Info”
Lang.: US English
Scr Saver: Load
Set LCD Contrast
Manufacturing Info
US English
US French
US Spanish
Exit
+
1x
Langue: US French
Eco ecran Charger
Régl Contraste LCD
Info Fabricant
Info Fabricant
Test Affichage
Test Touche
Sortie
Scroll to “Sortie” (Exit)
Initial Menu
d) Installation test
END
Scroll to “Inst. Test Missing”
+
SECURE Trailer
against movement!
During this test
all its brakes may
all its brakes may
be released auto-
matically! Press
ENTER to confirm
matically! Press
ENTER to confirm
you have secured
the Trailer.
= Confirm
Confirm that all
non connected
ports are plugged
then press ENTER.
= Confirm
Confirm that pneu-
matic connections
are secure, then
press ENTER.
= Confirm
2x
3x
Scroll and follow
instructions on the
screen
Installation test
is missing! To
start it browse to:
Main Menu->

10
User Manual
Confirm that the
Trailer‘s parking
brake is NOT active
then press ENTER.
...installation test continued.
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
Examples:
Confirm that wheel
speed sensors have
been set, then
press ENTER.
= Confirm
Confirm that the
Truck‘s parking
brake is applied
then press ENTER.
= Confirm
= Confirm
(if reservoir pressure > 6Bar)
2x
2x
Install. Check:
Reserv. Press:
S-C Sensor:
S-D Sensor:
Reserv. Press:
S-C Sensor:
S-D Sensor:
Demand Press:
S-C Sensor:
S-D Sensor:
Demand Press:
Tilt Angle:
< 5o
Installation test
has been success-
fully executed.
Please switch igni-
fully executed.
Please switch igni-
tion OFF-ON to
memorize status.
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
2x
END
Accelerate selected
wheel to 3mph
Fully apply brake
pedal
TEBS mounting angle
within tolorance
Confirm that
cables are securely
clipped, then
press ENTER.
= Confirm
Overview of wheel
location, “Confirm”
Overview of wheel
location, “Confirm”
Accelerate selected
wheel to 3mph

10

Knorr-Bremse Group
Superior Trailer Solutions To Maximize Performance And Keep You On The Road.
Take advantage of superior trailer braking systems and solutions that work best for your application.
Discover how Bendix trailer products and services can enhance your vehicle’s air brake system. Talk to your
Account Manager, call 1-800-AIR-BRAKE or visit www.bendix.com or www.foundationbrakes.com today.
Commercial Vehicle Systems
Bendix Commercial Vehicle S LLC
901 Cleveland Street
Elyria, Ohio 44035
USA
Tel: 1-800-AIR-BRAKE
Tel: [phone]
Fax: [phone]
www.Bendix.com
Y054277-US-001
This document is subject to alteration without notice and therefore a printed copy may not be the latest revision. Please check our website www.knorr-bremseCVS.com for the latest update or contact your local Knorr-Bremse representative.The gurative mark“K”and the trademarks KNORR and KNORR-BREMSE are registered in the name of Knorr-Bremse AG. Additional terms and conditions apply; please refer to our website knorr-bremseCVS.com under the“Documentation”tab. Note: If service work is carried out on a vehicle as a result of information taken from this document, it is the responsibility of the workshop to ensure the vehicle is fully tested and in full functional order before the vehicle is returned into service. Knorr-Bremse accepts no liability for problems caused as a result of appropriate tests not being carried out. Copyright 2011 © Knorr-Bremse AG - all rights reserved, including industrial property rights applications. Knorr-Bremse AG retains any power of disposal, such as for copying and transferring. 03/2011