Kodak ESP 5260 Instruction Manual

Note: A USB 2.0 cable is required to connect
your KODAK
All-in-One Printer to your
WINDOWS or MACINTOSH OS Computer.
Available
in the KODAK Store or see
your local retailer.
Remarque: Un cable
USB 2.0 est necessaire
pour relier I'imprimante avotre ordinateur
Windows ou Macintosh.
e e
CI
ar e e
Comme cez
oda ESP 5200 Series
oda ESP serie 5200
All-in-One Printer
Imprimante tout-en-un
Print Copy. Scan
Imprimer Copier· Numeriser
Includes Information on the:
ESP 5250 AII-in-One Printer
ESP 5260 AII-in-One Printer
Fournit des informations sur ces modeles :
Imprimante tout-en-un ESP 5250
Imprimante tout-en-un ESP 5260

Unpackingt e Pr-nter
Included with your KODAK All-in-One Printer:
PrintheadPower Cord
and
Adapter
=============
Black &Color
Ink Cartridges Software CD
IMPORTANT: To view asetup video for your printer, go to
WWW.KUUUK.c..Or I/gu/ In J::lLVIU .
a. Remove all shipping tape from the outside of the printer.
2
Printer Access Door
~ Scanner Lid
b. Lift the printer access door.
c. Remove all shipping tape and foam pieces from the inside of the
printer.
d. Close the printer access door.
www.kodak.comjgojaio5upport

Connecting the Power
a. Connect the:
•
power cord to the adapter
•
adapter to the printer
• power cord to the power source
b. Remove the plastic film from the LCD display and raise the control
panel.
c. Press ON <!).
d. Select your language and press OK.
e. Select your country/region and press OK.
www.kodak.com/go/aio5upport 3

Inser ig the Pre
ead
a. Lift the printer access door.
b. Carefully remove the printhead from its bag.
Do not touch the copper-colored contacts.
c. Remove the two plastic protective shields.
Carriage
d. Place the printhead into the carriage.
Insert at
the angle shown.
e. Push firmly against
the target label of the printhead until you hear
aloud snap.
4www.kodak.com/go/aio5upport

Iser ing the nk Cartri ge
a. Remove the black ink cartridge from its bag.
b. Carefully remove and discard the orange cap.
Handle ink cartridges carefully to avoid ink transfer.
c. Insert the black ink cartridge into the printhead.
d. Press down on the ink cartridge until you hear it click into
position.
e. Repeat steps 4a - 4d with the color ink cartridge.
f. Close the printer access door and press OK.
www.kodak.comjgojaio5upport 5

oad-ng Paper and Carbra ig
a. Open the front access door.
Paper Edge Guide
6
b. Move the paper edge guide to the left.
c. Load plain paper into the paper tray.
d. Move the paper edge guide to the edge of the paper.
e. Press Start. Calibration will take two to three minutes.
www.kodak.com/go/aiosupport

Con ect-ng to aComp ter 0ewo k
Choose one of the following options to connect your new printer to your computer. Refer to the
corresponding sections
for more information on connecting to a computer or network.
Allows you to connect to your printer using a USB cable.
Allows you to connect to your printer using awireless network.
Allows you to connect later to a computer or network.
NOTE:
You can change your connection type at alater date. See the last section in
this step or the chapter Setting Up Your Printer in the User Guide for detailed
instructions.
USB Cable Connection
U CABL co CTION-WAIT TO CON ECT
a. Select USB cable from the LCD display and press OK.
b. Continue with step 7 if you have a WINDOWS OS computer;
continue with step 8if you have a MACINTOSH computer.
Do not connect the
USB cable to the printer until instructed
during software install.
www.kodak.com/go/aiosupport 7

Wireless (Wi-Fi) Connection
For additional Wi-Fi/Networking setup
information, please go to:
www.kodak.comjg iIkletnetworking
=-
--
------' ----
---
I)))))) )
Determine if you are using aWPS (Wi-Fi Protected Software) enabled router or anon-WPS router. Follow
the appropriate steps below:
WPS Enabled Routers
a. Select WPS Connect from the LCD display.
b. Select
Push Button Configuration (recommended if you have aWPS router) or Generate WPS Pin.
Push Button Configuration
1. Select Push Button Configuration on the LCD display.
2. Select WPS on the LCD display.
3. You will have two minutes to push the WPS button on your router (this may either be aphysical
button on the router, or a virtual button in the router's software).
Generate WPS PIN
1. Select Generate WPS Pin on the LCD display.
2. Go to your router's software and locate the PI Nbutton.
(Refer
to your router's Web page for more information about WPS PIN.)
3. Enter the PIN you received on the LCD display into the PIN screen for your router.
c. If successfully connected, your Wi-Fi indicator should be solid blue. Continue with step 7 if you have
a
WINDOWS OS computer; continue with step 8 if you have a MACINTOSH computer.
If you are unable
to connect to your wireless network, go to vww kodak com/g('/i kiptnptworking
or refer to the User Guide at 'v vvV.KoaaK.com/go/ 01 ufor troubleshooting information.
8www.kodak.comjgojaiosupport

All Other Routers
You will need your wireless router settings:
Network Name (SSID): _
Security String: _
The
security string is unique to your network. Check with whomever set up your network, your Internet
provider, or check the network documentation for this information.
a. Select your wireless network from those listed and press OK.
If
the name (the SSID) of your network is not listed, make sure your wireless router is turned on and
within range.
If
your access point does not broadcast its SSID, then select Connect to Unlisted Network and press
OK.
b. Use the arrow keys and the OK button to enter your security string now.
NOTE: To use the virtual keyboard, select the letter you want and press OK. Select BKSP and press OK to
clear any mistakes you may make. When you are finished, select Done and press OK.
c. If successfully connected, your Wi-Fi indicator should be solid blue. Continue with step 7 if you have
a
WINDOWS OS computer; continue with step 8 if you have a MACINTOSH computer.
If you are unable
to connect to your wireless network, go to www.kodak.com/go/inkjetnetworking
or refer to the User Guide at www.kodak.com/go/manuals for troubleshooting information.
www.kodak.com/go/aiosupport 9

No Connection -Connect Later
You can connect your printer at alater time.
a. Select None from the LCD display and press OK.
b. Continue with step 7if you have a WINDOWS OS computer;
continue with step 8 if you have a MACINTOSH computer
To Change the Connection Type at aLater Time:
From aUSB connection to a Wi-Fi connection type
To change the connection type from USB to Wireless (Wi-Fi):
1. On the LCD display, select Network Settings> Wireless Setup Wizard.
2. Press OK. Follow the steps in the Wireless (Wi-Fi) Connection section.
3. After your printer is connected to your wireless network, go to
Start> Programs> Kodak> Kodak Printer Network Setup Utility. Follow the
on-screen instructions.
4.
To print to your Wi-Fi connected printer, choose Kodak 5250 - XXXX Printer or
5260 - XXXX Printer (where XXXX is a number unique to your printer).
From a Wi-Fi connection type to aUSB connection type
To change the connection type from Wireless (Wi-Fi) to USB:
1. Connect your USB cable to your printer and computer. The necessary drivers
will install automatically.
2. To print to your USB connected printer, choose Kodak 5250 Printer or
Kodak 5260 Printer.
10 www.kodak.com/go/aiosupport