Kodak ESP 3 - All-in-One Color Inkjet Instruction Manual

3
Start Here
All-in-One Printer
Print
Copy
Scan
Note: A USB 2.0 (High Speed) cable is required to connect your Kodak All-in-One printer to your Windows
or Macintosh OS computer.

2www.kodak.com/go/aiosupport
10
ColorInk Car tridge
10
ColorInk Car tridge
Inkjet Printer Software
FOR WINDOWS & MACINTOSH
Power Cord and Adapter Printhead Ink Cartridges Software and
User Guide CD
Unpacking the Printer
1
Do not connect the USB cable to the printer until instructed during
software installation.
USB
a) Remove all orange shipping tape and any foam pieces
from the outside of the printer.
b) Lift the printer access door.
c) Remove all orange shipping tape and any foam
pieces from the inside of the printer.
ColorInkCartridge
10
10
BlackInkCartridge
10
BlackInkCartridge
Carriage .
Printer access
door
.
Scanner lid .
Front access door .

3
www.kodak.com/go/aiosupport 3
a) Lift the printer access door.
b) Remove the printhead from its bag.
Insert the printhead immediately upon
opening sealed bag. The printhead is fragile,
handle carefully.
c) Pull on the orange tab to remove the
protective retainer.
2Inserting the Printhead
ColorInkCartridge
10
10
BlackInkCartridge
10
BlackInkCartridge

4www.kodak.com/go/aiosupport
d) Carefully remove and discard the orange
protective cap.
Do not touch the copper-colored contacts.
e) Place the printhead into the carriage.
Insert at the angle shown.
f) Push firmly against the target label of the printhead
until you hear a loud snap.
2
Carriage .

5
www.kodak.com/go/aiosupport
a) Remove the black ink cartridge from its bag.
Insert ink cartridges immediately upon opening
sealed bag.
b) Carefully remove and discard the orange cap.
Handle ink cartridges carefully to avoid ink transfer.
c) Insert the black ink cartridge into the printhead.
d) Press down on the ink cartridge until you hear it click
into position.
3Inserting the Ink Cartridges
10
10
10
Black Ink Cartridge
10
BlackInkCartridge
10
Cartouche d'encre noire
10

6www.kodak.com/go/aiosupport
e) Open and uncap the color ink cartridge. Insert it into
the printhead.
f) Press down firmly on the ink cartridge until you hear it
click into position.
g) Close the printer access door.
3
10
Cartouche d'encre noire
Cartouche d'encre couleur
10
ColorInkCartridge
10
10
BlackInkCartridge
10
BlackInkCartridge
ColorInkCartridge
10
10
Cartouche d'encre noire
10
Cartouched'encrecouleur

7
www.kodak.com/go/aiosupport
4Connecting Power
Do not load paper until after software installation is complete.
a) 1. Connect the power cord and adapter.
2. Connect adapter to printer.
3. Connect to power source.
b) Press ON .
A flashing “E” in the quantity window indicates the
printhead is not installed correctly. Remove the ink
cartridges and reinstall the printhead.

8www.kodak.com/go/aiosupport
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
a) Load the Kodak Inkjet Printer Software CD into the
CD-ROM drive. Follow the on-screen prompts
when the instructions appear.
If instructions do not appear, click Start, then Run.
Select CD-ROM drive and type setup.exe, then
press ENTER.
b) Connect the USB cable to the printer when
instructed. Continue to follow the on-screen
prompts until installation is complete.
FOR WINDOWS & MACINTOSH
5
Installing Windows Software
Do not connect the USB cable to
the printer until instructed during
software installation.
USB
Start Printers and Faxes
Right-click the icon for the printer you want to use as the default printer, and
then click Set As Default Printer.
Start Control Panel Hardware and Sound Printers
Right-click on the printer you want to use, and then click Set As Default Printer.
Setting your KODAK All-in-One Printer as the default on your WINDOWS OS
WINDOWS XP:
WINDOWS VISTA:
WINDOWS

MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
Install Macintosh Software
www.kodak.com/go/aiosupport 9
FOR WINDOWS & MACINTOSH
5
a) Connect the USB cable to the printer and your
Macintosh computer.
b) Load the Kodak Inkjet Printer Software CD into the
CD-ROM drive.
The Kodak Inkjet Printer software installer window
should be displayed. If not, double-click the Kodak
Inkjet Printer Software CD icon on the desktop.
Follow the on-screen prompts until installation
is complete.
MACINTOSH
MAC OS X defaults to the printer most recently added. To change the default printer, follow these steps:
1. From the print dialog, choose Edit Printer List from the Printer pop-up menu.
2. Select a printer from the Printer List.
3. Choose Make Default from the Printer’s menu.
Setting your KODAK All-in-One Printer as the default on your MACINTOSH OS

10 www.kodak.com/go/aiosupport
a) Lower the front access door and pull the paper tray all
the way out.
b) Insert a small stack of 5 to 10 sheets of plain paper
into the paper tray. Squeeze the paper edge guide and
slide it guide against the left edge of the paper.
Leave the paper tray extended.
NOTE: For photo paper, insert a stack of paper into the
paper tray face down.
Leave the paper tray extended.
c) Flip up the paper stop.
6Loading Paper
Paper tray
Paper edge guide
.