Kodak dryview 8300 User manual

SERVICE MANUAL
Kodak DryView 8300 LASER IMAGER
1908110
78-6970-7393-6
12/04 Rev. S

Service Manual
a1908110 2004 December Rev. S
Revision History
The original issue and revisions of this SERVICE MANUAL for the Kodak DryView 8300 LASER IMAGER
are as follows:
Issue Date (Rev. A): 12/96, Rev. B: 3/97, Rev. C: 5/97, Rev. D: 8/97, Rev. E: 10/97, Rev. F: 3/98,
Rev. G: 8/98, Rev. H: 4/99, Rev. J: 10/99, Rev. K: 3/00, Rev. L: 8/00, Rev. M: 3/01, Rev. N: 9/01,
Rev. P: 3/02, Rev. Q: 9/03, Rev R: 3/04, Rev S: 12/04
The current revisions for the manual is as follows:
Section Text
Rev. Pages Changed in Current Revision
Title/a STitle and a pages
Warnings M--
TOC R
1Q
2S2--27
3S3--1, --2, --3
4R
5S5--1, --2
6P
7S7--123 thru 7--128
8S8--16
9Q
10 Q

WARNINGS AND CAUTIONS
i2001 March Rev. M 1908110
Warnings and Cautions
Read and understand all instructions before using.
!WARNING
This equipment is operated with hazardous voltage which can shock, burn, or cause
death.
Remove wall plug before servicing equipment. Never pull on cord to remove from outlet. Grasp plug and
pull to disconnect.
Do not operate equipment with a damaged power cord.
Do not use an extension cord to power this equipment.
Use only the power cord supplied with the equipment.
Position the power cord so it will not be tripped over or pulled.
Connect this equipment to a grounded outlet.
Do not place a portable multiple socket outlet (power strip) on the floor. Mount the power strip on a wall or
on the underside of a table.
!WARNING
Do not use in the presence of flammable anesthetics, oxygen or nitrous oxide. This equipment does not
have a gas sealed electronics enclosure and could ignite any flammable or explosive gases present in its
environment.
!WARNING
Not protected against ingress of liquids including bodily fluids.
!WARNING
For continued protection against fire, replace fuses only with fuses of the same type and fuse rating.
!CAUTION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. Those limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.

SERVICE MANUAL
ii 1908110 2001 March Rev. M
!CAUTION
This equipment is intended to connect to other medical devices. Installation and service maintenance are
to be performed only by qualified service personnel.
!CAUTION
Do not substitute or modify this equipment without approval of Eastman Kodak Company.
!CAUTION
U.S. Federal law restricts sale of this device to or on the order of a licensed health care practitioner.
!CAUTION
Avoid Laser Beam
This equipment employs an invisible 25 milliwatt laser. Laser radiation may be present
when the machine operates without panels or covers installed.
Use of controls or adjustments, or performance of procedures other than those specified herein, may
result in eye damage.
Covers shall be removed by authorized service personnel only.
There are no “user’ serviceable parts in this machine other than the charcoal odor filter.
!CAUTION
Avoid touching the developer drum when removing film jams from the imager. The developer drum may
become hot during extended imager operation.
D8300--134A

WARNINGS AND CAUTIONS
iii2001 March Rev. M 1908110
Type B Applied Part
--DANGER Invisible Laser Radiation When Open.
Avoid Direct Exposure to Beam.
--ATTENTION Rayonnement Laser Invisible En Cas
DÕOuverture. Exposition Dangereuse
Au Faisceau.
--VORSICHT Unsichtbare Laserstrahlung Wenn Abdeckung
Geoffnet. Nicht Dem Strahl Aussetzen.
--VARNING Osynlig Laserstrlning. Laserstrining Nar
Denna Del A Oppnad. Strlen Ar Farlig.
D8300--134A
CAUTION: Disconnect Power Before Servicing.
ATTENTION: Couper Le Courant Avant D’ourvir
L’Appareillage Pour Service.
ACHTUNG: Gerat Vom NetzTrennen Bevor Service.
This equipment complies with part 15 of the FCC Rules: And Radio Interference
Regulation of the Canadian Department of Communication.
Operation of this equipment ina residential area may cause unacceptable
interference to radioand televisionreception requiring the operator to take
whatever steps are necessary tocorrectÊthe interference.
This product complies with CDRH Regulation21 CFR Subchapter J.
Class 1 laser product to IEC 825.
Laser klasse 1 produkt nach IEC 825.
Date of Manufacture
Laser de cate gories 1 IEC 825.
100 -- 240 Volts 50 -- 60 Hz 6.3 / 3.2 Amps
Made in USA
Agency Approvals
Class 1 laser product to IEC 825.
Laser klasse 1 produkt nach IEC 825.
Laser de cate gories 1 IEC 825.
.. .. ..
..
Part No:
Serial No:
Options:
!CAUTION
General External Cleaning: This equipment may be cleaned with a damp cloth using water with mild
detergent, or commercial electronic equipment cleaner.
Classifications
UL Classified
File Number E163816
Control Number 48VF
Medical Equipment
UL 2601-1 CAN/CSA No. 601.1
!Classified by Underwriters Laboratories Inc.With Respect to Electric Shock, Fire, Casualty and
Medical Hazards only in Accordance with UL 2601-1, CAN/CSA C22.2 No. 601.1 and IEC 601-1.

SERVICE MANUAL
iv 1908110 2001 March Rev. M
BLANK PAGE

AGENCY, REGULATORY, AND CE MARKING
v2001 March Rev. M 1908110
Agency, Regulatory, and CE Marking Compliance
All Agency, Regulatory, and CE Marking information may be found in the User Guide for this model.

SERVICE MANUAL
vi 1908110 2001 March Rev. M
BLANK PAGE

TABLE OF CONTENTS
vii
2004 March Rev. R 1908110
PLEASE NOTE The information contained herein is based on the experience and knowledge relating
to the subject matter gained by Eastman Kodak Company prior to publication.
No patent license is granted by this information.
Eastman Kodak Company reserves the right to change this information without notice
and makes no warranty, express or implied, with respect to this information. Kodak
shall not be liable for any loss or damage, including consequential or special
damages, resulting from the use of this information, even if loss or damage is caused
by Kodak’s negligence or other fault.
Table of Contents
Description Page
Revision History 1................................................
Warnings and Cautions i..........................................
Agency, Regulatory, and CE Marking Compliance v.................
Section 1 -- Specifications 1-1.......................................
1-1. Dimensions 1-1.....................................................
1-2. Electrical 1-1.......................................................
1-3. Operating Environment 1-1..........................................
1-4. Non-Operating Environment: 1-1......................................
1-5. Image Area Limits 1-1...............................................
1-6. Hardware Interface (Input Modules) 1-2...............................
1-7. Control Interfaces 1-2...............................................
1-8. Output 1-2.........................................................
1-9. Film Characteristics 1-2..............................................
1-10. Options 1-2........................................................
1-11. Memory 1-2........................................................
Section 2 -- Installation 2-1..........................................
2-1. INSTALLATION CHECKLIST 2-1.....................................
2-2. Unpacking 2-1......................................................
2-3. Connecting CABLES and EXTERNAL DEVICES 2-2....................
2-3-1. DIGITAL INPUT MODULES 2-2...............................
2-3-2. ANALOG INPUT MODULES 2-2...............................
2-3-3. SCSI INPUT MODULES 2-3..................................
2-3-4. NETWORK INPUT MODULES 2-3.............................
2-4. Energizing the System 2-4...........................................

SERVICE MANUAL
viii 1908110 2004 March Rev. R
Description Page
2-5. Setting Up the System 2-4...........................................
2-5-1. Setting Up Parameters for DIGITAL INPUT MODULES 2-5.......
2-5-2. Setting Up Parameters for ANALOG (VIDEO) INPUT MODULES 2-8
2-5-3. Setting Up Parameters for the SCSI INPUT MODULES 2-15.......
2-5-4. Setting Up Parameters for NETWORK INPUT MODULES 2-18.....
2-6. Setting Up the Memory Parameters (Memory Management) 2-22..........
2-7. Setting Up Customer Preferences 2-23.................................
2-8. Final Checkout 2-25..................................................
2-9. Installing Software Upgrades 2-26.....................................
2-9-1. Installing Software Using HyperTerminal 2-26....................
2-9-2. Installing Software using Procomm Plus 2-27.....................
2-10. Installing Software Upgrades for NETWORK INTERFACE BOARDS 2-29...
2-11. VIDEO Installation Parameters 2-30....................................
2-12. Contrast and Density Requirements for 8300 LASER IMAGERS 2-35......
2-13. New ULUT Options 2-37..............................................
Section 3 -- Adjustments 3-1.........................................
3-1. Setting Up the Processor Temperature 3-1.............................
3-2. Processor Drum Stripper Assembly 3-4................................
3-3. One Sheet and Two Sheet Switches 3-7...............................
3-4. Capstan Media Sense Switch 3-9.....................................
3-5. Film Saver Switch 3-11...............................................
3-6. Film Out Switch 3-12.................................................
3-7. Film Tray In-Place Switch 3-13.........................................
3-8. Film Tray Lock Switch 3-14............................................
3-9. Capstan Belt 3-15....................................................
3-10. Separator Roller Belt 3-16............................................
3-11. Main Drive Belt 3-17..................................................
3-12. Processor Belt 3-18..................................................
3-13. Processor Drive Arm Gear 3-19........................................