Kodak Advantix C650 User manual

Kodak
C650 Zoom
Camera
ENGLISH/ESPAÑOL/PORTUGUÊS

Camera Identification
(1)
(2) (3)(4) (5)
(6)(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)

Camera Identification
(17) (18)(19)
(20)
(21)
(22)
(23)
(24)
(25)

AUTO
OFF
+
LCD Panel
(34) (33) (32)
(26) (27) (28)
(29)
(30)
(31)
(35)
(36)

This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: Your model camera has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits provide
reasonable protection against interference in residential use. The camera generates,
uses and can radiate radio frequency energy and, if not used in accordance with
the instructions, may cause interference to radio communications. There is no
guarantee that interference will not occur. If this camera does cause interference to
radio or television reception, which can be determined by turning the camera off and
on, you may reduce the interference by the following:
— Reorient or relocate the receiving antenna.
— Increase the separation between the camera and the receiver.
— Consult the dealer or an experienced radio/television technician for help.
Changes or modifications not approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

ENGLISH
KODAKADVANTIX
C650 Zoom Camera
Welcome to the innovative world of the Advanced Photo System!
And thank you for buying this KODAK ADVANTIX Camera.
NEED HELPWITHYOUR CAMERA?
Go to our web site at http://www.kodak.com or call:
Kodak in your country.
When you call, please have your camera available.
For warranty purposes, please keep your sales receipt as proof of
the date of purchase.
©EastmanKodakCompany,1998

2
ADVANCED PHOTO SYSTEM
FEATURESAVAILABLE
WITH THIS CAMERA
Triple format selection
• You can take three different size
pictures: Classic (C), Group/HDTV (H),
and Panoramic (P) pictures from the
same film cassette. The viewfinder
frame changes to match each format
selection.
Date and time imprinting
• You can choose to have date and time
information printed on the back of your
prints. See your photofinisher for a full
description of available services.
Double exposure protection (DEP)
• You don’t need to worry about
accidentally re-exposing your film.
Your camera reads the Film Status
Indicator (FSI) on the film cassette
to prevent re-exposure.
Picture quality information
exchange (PQix)
• Your camera features magnetic
information exchange that records
information about lighting conditions
and exposure on the film cassette to
assist the photofinishing lab with color
correction and exposure adjustments,
providing you with the best possible
results.
Safety-interlock film door
• The safety interlock on the film door
prevents the door from opening before
the film is completely rewound.

3
Film Status Indicator (FSI)
A highlighted indicator advances from
one symbol to another to identify the
status of the film inside the cassette.
4
3
2
1
Look for this logo to be certain that the film you buy is
made for this camera.
Look for this logo to select a certified photofinisher for
developing your film and to assure that you get all the
features of the Advanced Photo System.
PROCESSED NEGATIVES
FULLY
EXPOSED
PARTIALLY
EXPOSED
UNEXPOSED

4
CONTENTS
CAMERA IDENTIFICATION............................. 5
ATTACHINGTHE STRAP ................................ 6
LOADINGTHEBATTERY ................................ 6
Low-battery indicator ................................... 7
Battery tips .................................................. 7
Power shut-off ............................................. 7
LOADING THE FILM ........................................ 8
TAKING PICTURES......................................... 9
Typical print sizes (formats) ....................... 10
Using the focus lock .................................. 10
Using the zoom lens .................................. 11
Tips for better pictures ............................... 11
TAKING FLASH PICTURES .......................... 12
Flash-to-subject distance .......................... 12
SELECTINGTHEFLASHAND
INFINITY-FOCUS MODES .......................... 13
Red-eye reduction ..................................... 13
Auto flash without red-eye reduction ......... 14
Fill flash ..................................................... 14
Off flash ..................................................... 15
Infinity focus .............................................. 15
Night-view.................................................. 16
USING THE SELF-TIMER ............................. 16
DATE AND TIME IMPRINTING ...................... 17
Setting the date and time .......................... 17
UNLOADING THE FILM................................. 17
Automatic rewind ....................................... 17
Manual rewind ........................................... 18
CARING FOR YOUR CAMERA ..................... 18
TROUBLESHOOTING ................................... 19
SPECIFICATIONS.......................................... 20

5
CAMERAIDENTIFICATION
(Unfold the front and back cover flaps of manual for camera diagrams.)
20 ON/OFF SWITCH
21 FILM-DOOR LATCH
22 STRAP POST
23 FILM CHAMBER
24 FILM DOOR
25 TRIPOD SOCKET
LCD Panel
26 BATTERY SYMBOL
27 DATE/TIME DISPLAY
28 NIGHT-VIEW INDICATOR
29 RED-EYE-REDUCTION INDICATOR
30 FRAME COUNTER
31 SELF-TIMER INDICATOR
32 FILL-FLASH INDICATOR
33 INFINITY-FOCUS INDICATOR
34 FILM-PRESENCE INDICATOR
35 OFF-FLASH INDICATOR
36 AUTO-FLASH INDICATOR
1ZOOM-DIAL LEVER
2SELECT BUTTON
3ENTER BUTTON
4FILM-REWIND BUTTON
5LCD PANEL
6SELF-TIMER BUTTON
7FLASH-MODE BUTTON
8FORMAT-SELECTOR LEVER
9FLASH
10 VIEWFINDER
11 LENS
12 METER-CELL WINDOW
13 SELF-TIMER LAMP
14 RED-EYE-REDUCTION LAMP
15 AUTO-FOCUS SENSORS
16 SHUTTER BUTTON
17 BATTERY DOOR
18 FLASH/CAMERA-READY LAMP
19 VIEWFINDER EYEPIECE

6
Use KODAK
ADVANTIX Film
ATTACHING THE STRAP
1. Insert the shorter looped end of the
strap behind the STRAP POST (22).
2. Thread the longer end of the strap
through the shorter loop.
3. Pull the strap tight.
LOADING THE BATTERY
This camera uses one 3-volt lithium
KODAK K123LA (or equivalent) Battery
that supplies power for all camera
operations.
1. Open the
BATTERY
DOOR (17).
•Before you
remove the
old battery,
turn the
cameraoff.
2. Insert the
battery into
the chamber
asshown.
3. Snap the
battery door
closed.
•After you
load a new
battery into the camera, you will
need to reset the date and time.

7
Low-battery indicator
It’s time to replace the battery when—
• the BATTERY SYMBOL (26) “blinks” on
the LCD PANEL (5) or
• none of the indicators appears on the
LCD panel and the SHUTTER
BUTTON (16) cannot be released.
Battery tips
• Remember to keep a spare battery
with you at all times.
• Read and follow all warnings and
instructions supplied by the battery
manufacturer.
• Keep batteries away from children.
• Do not try to take apart, recharge or
short circuit the battery, or subject it to
high temperature or fire.
• Store batteries in their original
packaging prior to use.
Power shut-off
To save battery power, the camera will
automatically go into a sleep mode (lens
will return to the wide-angle position and
the LCD panel will display just the date/
time) if it is not operated for more than
3 minutes. You can press any of the
control buttons to awaken the camera.

8
LOADING THE FILM
You can load film into the camera with
the camera ON or OFF.
1. Move the
FILM-DOOR
LATCH (21) to
open the
FILM
DOOR (24).
• The film
door will
open only
when the film chamber is empty or
the film in the camera is completely
rewound into the film cassette.
2. Insert the film cassette completely
into the FILM CHAMBER (23).
•Make
sure the
Film
Status
Indicator
(FSI) on
the film
cassette
is at ●
(#1 position) for a new cassette.
•Do not force the film cassette into
the film chamber.
3. Close the film door to start the auto-
film advance. The FRAME COUNTER (30)
on the LCD PANEL (5) will show the
number of frames remaining on the
film cassette.
• After you close the safety-interlocked
film door, you cannot open the door
until the film is completely rewound
into the film cassette.
OPEN
ON
OFF
432
1
ON OFF
OPEN

9
TAKING PICTURES
You can take Classic (C), Group/ HDTV (H) *,
and Panoramic (P) pictures on the same
film cassette. Your photo-processing cost
may be based on the format size(s) that
you use to expose the film.
1. Move the ON/
OFF SWITCH (20)
to the “ON”
position to turn
the camera on
and to raise the
FLASH (9).
2. Move the
FORMAT-
SELECTOR
LEVER (8) to
select desired
format (C, H,
or P). The
viewfinder will
change to show the selected field
of view.
3. Frame your subject within the
VIEWFINDER EYEPIECE (19). For a sharp
picture, stand at 0.6 m from your
subject.
4. Press the SHUTTER BUTTON (16) to
take the picture.
ON OFF
OPEN
C
P
H
C
P
H
* High Definition Television (HDTV) prints are
the same aspect ratio as the TV for CD
interface capabilities.
SELECT
ENTER
OPEN
OFFON

10
Typical print sizes (formats)
CHP
Classic Group(HDTV) Panoramic
88.9 x 127 mm or 88.9 x 152 mm or 88.9 x 216 mm to
102 x 152 mm 102 x 178 mm 102 x 292.7 mm
NOTE:Your photofinisher will generally provide
102 x 152, 102 x 178, and 102 x 292.7 mm sizes. Some
localprinters mayoffer 88.9x 127,88.9 x152, and
88.9 x 216 mm sizes.
Using the focus lock
This camera automatically focuses on
whatever is within the auto-focus (AF)
circle of the viewfinder eyepiece. To get a
sharp picture, make sure the AF circle is
on your main subject. If you want to take
a picture with the subject positioned
outside of the AF circle, use the focus
lock as follows:
1. Place the AF circle on the subject that
you want focused in the picture.
2. Partially depress and hold the
SHUTTER BUTTON (16) to lock the
focus position.
3. While still partially depressing the
shutter button, move the camera until
your subject is where you want it within
the VIEWFINDER EYEPIECE (19).
4. Press the shutter button completely
down to take the picture.
AF CIRCLE
VIEWFINDER
VIEWFINDER

11
Using the zoom lens
This camera has a motorized zoom lens
that lets you select the ideal lens-focal
length for taking pictures. When you turn
the camera on, it is initially set to the
wide-angleposition.
1. Move the ON/OFF SWITCH (20) to the
“ON” position to turn the camera on
and to raise the FLASH (9).
2. Move the
ZOOM-DIAL
LEVER (1) to
the left to the
wide-angle
position to
zoom away
from the
subject. Move
the lever to the right to the telephoto
position to zoom closer to the subject.
3. Frame your subject within the
VIEWFINDER EYEPIECE (19).
4. Press the SHUTTER BUTTON (16) to
take the picture.
• The lens barrel will automatically
return to the wide-mode position after
approximately 3 minutes.
Tips for better pictures
• Move close enough to your subject
so it fills the viewfinder but not closer
than 0.6 m.
• Take pictures at the subject’s level.
Kneel down to take pictures of children
and pets.
• Hold your camera vertically to
capture tall, narrow subjects, such
as a waterfall, skyscraper, or a
single person.
• Add interest to your picture by framing
it with a tree branch, a window, or even
the rails of a fence.
• Keep the sun behind you. This provides
the best subject illumination.
OPEN
ON

12
TAKING FLASH PICTURES
In dim light, such as indoors or outdoors
in heavy shade, or on dark overcast days,
you need flash. Your camera features an
automatic flash that fires when you need
it. The pop-up flash helps to minimize red
eyes in flash pictures and to prevent hand
obstruction in front of the lens.
1. Move the ON/OFF SWITCH (20) to the
“ON” position to turn the camera on
and to raise the FLASH (9).
• The FLASH/CAMERA-READY LAMP (18)
“blinks” when the flash is not ready.
2. Frame your subject within the
VIEWFINDER EYEPIECE (19).
3. Partially depress the SHUTTER
BUTTON (16). When the FLASH/CAMERA-
READY LAMP (18) glows green, fully
depress the shutter button to take
the picture.
4. Keep the subject
within the
distance range
for the speed of
film in your
camera (see
Flash-to-subject
distance). Don’t
take pictures beyond the maximum
distance or your pictures will be dark.
Flash-to-subject distance
ISO film Wide Telephoto
speed (24 mm) (48 mm)
50 0.6 to 4.3 m 0.6 to 2.1 m
100 0.6 to 5.8 m 0.6 to 3.1 m
200 0.6 to 8.2 m 0.6 to 4.3 m
400 0.6 to 11.6 m 0.6 to 6.1 m
800 0.6 to 16.2 m 0.6 to 8.5 m
1600 0.6 to 22.6 m 0.6 to 12.2 m

13
SELECTING THE FLASHAND
INFINITY-FOCUS MODES
Besides the auto-flash mode with red-
eye reduction, you can select
auto-flash without red-eye reduction,
fill flash, off-flash, infinity-focus, and
night-view modes.
Press the FLASH-
MODE BUTTON (7)
until the desired
indicator appears
on the LCD
PANEL (5).
The flash modes will remain selected
after you take the picture. To change
the flash-mode selection, press the
flash-mode button, or turn the camera
off then back on to return to the flash
default mode.
Red-eye reduction
Some people’s eyes (and some pets’) can
reflect flash with a red glow. This camera
features automatic flash with red-eye
reduction which is the intitial default setting
for this camera. With the help of the pop-up
flash and by following the instructions
below, you can minimize red eyes in flash
or fill-flash pictures.
1. Move the ON/OFF SWITCH (20) to the “ON”
position to turn the camera on and to
raise the FLASH (9).
2. Press the FLASH-MODE BUTTON (7)
repeatedly until the auto flash with RED-
EYE-REDUCTION INDICATOR (29) appears
on the LCD PANEL (5).
• Disregard step 2 if the default setting is
already set for red-eye reduction.
3. Frame your subject within the VIEWFINDER
EYEPIECE (19).
4. Have your subject look directly at the
RED-EYE-REDUCTION LAMP (14).
5. Partially depress the SHUTTER BUTTON (16).
When the FLASH/CAMERA-READY LAMP (18)
glows green, fully depress the shutter
button to take the picture.

14
Auto flash without red-eye
reduction
Use this mode for taking pictures
without people.
You can change the default setting to
auto flash without red-eye reduction by
following the steps below:
1. Move the ON/OFF SWITCH (20) to the
“ON” position to turn the camera on
and to raise the FLASH (9).
2. Press the FLASH-MODE BUTTON (7)
repeatedly until the AUTO-FLASH
INDICATOR (36) appears on the
LCD PANEL (5).
3. Frame your subject within the
VIEWFINDER EYEPIECE (19).
4. Partially depress the SHUTTER
BUTTON (16). When the FLASH/CAMERA-
READY LAMP (18) glows green, fully
depress the shutter button to take
the picture.
• The camera will now default to the
auto-flash mode without red-eye
reduction.
Fill flash
When bright light indoors or outdoors
comes from behind the subject (backlight-
ing), dark shadows (especially on faces)
may occur. Use fill flash to lighten
these shadows.
1. Move the ON/OFF SWITCH (20) to the
“ON” position to turn the camera on
and to raise the FLASH (9).
2. Press the FLASH-MODE BUTTON (7)
repeatedly until the FILL-FLASH
INDICATOR (32) appears on the LCD
PANEL (5).
3. Frame your subject within the
VIEWFINDER EYEPIECE (19).
4. Partially depress the SHUTTER
BUTTON (16). When the FLASH/CAMERA-
READY LAMP (18) glows green, fully
depress the shutter button to take
the picture.

15
Off flash
When you do not want to use the flash,
especially indoors where flash is
prohibited, such as in theaters and
museums, or when you want to take
twilight scenes or distant subjects that are
beyond the flash range, or capture the
ambiance of existing light, use the off-
flash feature. Use a tripod or place the
camera on another firm support, and use
high-speed film because the shutter
speed at night will most likely be slow.
1. Move the ON/OFF SWITCH (20) to the
“ON” position to turn the camera on
and to raise the FLASH (9).
2. Press the FLASH-MODE BUTTON (7)
repeatedly until the OFF-FLASH
INDICATOR (35) appears on the
LCD PANEL (5).
3. Frame your subject within the
VIEWFINDER EYEPIECE (19).
4. Partially depress the SHUTTER
BUTTON (16). When the FLASH/CAMERA-
READY LAMP (18) glows green, fully
depress the shutter button to take
the picture.
Infinity focus
Capture sharp, distant scenery at any
zoom position (for daylight and outdoor
use only).
1. Move the ON/OFF SWITCH (20) to the
“ON” position to turn the camera on
and to raise the FLASH (9).
2. Press the FLASH-MODE BUTTON (7)
repeatedly until the INFINITY-FOCUS
INDICATOR (33) appears on the LCD
PANEL (5).
3. Frame your subject within the
VIEWFINDER EYEPIECE (19).
4. Partially depress the SHUTTER
BUTTON (16). When the FLASH/CAMERA-
READY LAMP (18) glows green, fully
depress the shutter button to take
the picture.
OFF