Kogan NBLTFSLM25A User manual

SOLAR POWERED MOTION SENSOR
LED COMPACT FLOOD LIGHT
(2500MAH)
NBLTFSLM25A

•Do not install this light in a location with close proximity to people or vehicles.
•Keep children and infants away from the light.
•Do not install this light in a location near flammable items.
•Ensure the light is installed on a flat surface. Do not install it in an unstable
location.
•The solar panel should be toward the sun for charging. Ensure the panel is clean
before charging.
•Do not stare directly into the light while it is on. This may cause serious injury.
•Do not install it close to devices that send radio waves. There is risk of radio
interference.
•To prevent from falling, ensure the base unit is installed tightly with expansion
screw.
•This product cannot prevent crimes by itself, nor guarantee to deter criminals or
trespassers. It is intended to alert users of motion.
•Ensure the solar panel jack is fully inserted into the light head fixture socket.
SAFETY & WARNINGS

1
Lamp
8
ON/OFF Switch
2
Solar Panel (1.8m wire)
9
Battery Housing inlet
3
Expansion screw
10
Solar Panel Mounting Bracket
4
LED
11
LUX Adjusting Knob
5
Battery Housing
12
SENS Adjusting Knob
6
Motion Detector Head
13
TIME Adjusting Knob
7
“U” shaped Mounting Plate
14
Lithium Battery (not shown)
PRODUCT OVERVIEW

1. The light should be set up at a location where you desire to have extra lighting to
detect persons or objects moving at night or in the dark. Decide an idea location
prior to installing.
2. Decide where you want to place both the lamp (1) and solar panel (2). The light is
equipped with 5 metres of connecting wire, so the lamp (1) and solar panel (2) can
be installed up to 5 metres apart.
3. The solar panel (2) must be set in a location that receives full, direct sunlight a
minimum of 8 hours a day. A wall or roof are ideal locations.
4. Mount the lamp (1) 2-to-3 metres above ground on a solid surface capable of
supporting the lamp (1), and secure enough so that it will not move when exposed
to vibration or wind. The unit must be high enough to allow for motion detection
and light distribution.
5. Using the mounting plate as a template, mark certain that the drilling path is clear
of obstacles such as cable and electrical line. Place mounting bracket (7) on drilled
holes and thread in the enclosed mounting screws to secure mounting bracket in
position.
6. Follow the above steps (steps 4 and 5) to install the solar panel (2).
7. Carefully route the power cord of the solar panel (2) to the lamp (1) and plug it into
the battery housing outlet (9).
8. Adjust the motion detector head (6) below the light by moving it left or right so that
it faces the area where movement will occur. Move it up or down by using the screw
located on the neck of motion detector head (6).
INSTALLATION NOTES

•Before the solar sensor light can operate to its full capacity, the solar panel needs
to be in sunlight for three days to fully charge the battery. Turn the switch to the
“off” position. After the charge, turn the switch to “on” position.
•Tu r n the switch to “on” position, the light will turn on automatically at night when
motion is detected by the motion detector head (6).
Charging the battery
1. The battery charges via sunlight to the solar panel.
2. The “On” / “Off” switch (8) controls the light. Whether off or on, the solar panel will
still charge if in sunlight, but the light will only function when switched to “On”.
3. When charging, the solar panel should be facing toward the sun. If the solar panel
is dirty, it cannot charge the battery efficiently.
How to use the On/Off switch
OFF Inside position
When you do not need lighting.
ON Outside position
Light turns on automatically.
OPERATION

How to use Control Knobs
•The solar sensor light has 3 different control knobs: LUX, TIME and SENS.
LUX (Light level for motion detection)
1. The LUX adjusting knob (10) tells the sensor the level of darkness that must be
reached before the light turns on.
2. If set to the maximum level, the light will go on in most situation ranging from
dark to daylight.
3. If set to the minimum setting the sensor will only trigger the light to turn on at
dusk or when it is dark out. This is the ideal position for general evening and night
operation. If the solar sensor light is not operating at night due to interference from
a streetlight or other interference, turn the LUX knob towards .
Time
1. The time adjusting knob (12) sets the duration of time that the light should stay lit
after motion is no longer detected in the field of vision.
2. The time is adjustable from 8 seconds to 2 minutes. Moving the knob clockwise will
make it stay on longer.

SENS (Sensitivity)
Sensitivity is affected by distance conditions. In the hot outside, the sensor has difficulty in
detecting changes in heat. In cold temperatures, the sensor has easily to detecting changes
in heat.
Minimum SENS Position
Turn the dial counterclockwise to the minimum setting. Ideal for short distance conditions. If
the sensitivity is a tripping nuisance, it can be reduced by turning the knob counterclockwise
towards the minimum setting.
Maximum SENS Position
Turn the dial clockwise to the maximum setting. This is ideal for long-distance conditions. If
the sensitivity is not enough, it can be increased by turning the knob clockwise towards the
maximum setting.
Note:
Turn the dial anywhere between the minimum and maximum setting to adjust the
level of sensitivity, as needed.

1. When storing your “Solar Sensor Light” indoor for more than 2 or 3 days, turn the
switch to “off”. Store the light in a dry location free of dust and debris. Make certain
that the light is out of reach of children.
2. The light must be fully charged 5 days and switch “off” position before storing.
Storing the light for prolonged periods may damage the light or decrease
performance.
3. Keep the solar panel from dirt and debris. A dirty solar panel will not keep the
batteries from charging. Clean regularly with a damp cloth.
4. Keep the solar panel free of dirt, dust and grime. Dust covering the solar panel will
block out the sunlight causing a decrease or stoppage of efficiency in recharging
the batteries.
Battery Replacement
1. The battery pack is a location in the battery housing (5).
2. Turn the switch (8) to the “off” position. Remove the four screws from the battery
housing (5). Separate the battery pack connector. Remove the old battery pack.
Replace only with an identical rechargeable battery (14).
3. Replace the cover of the battery housing (5). Secure it with the four screws.
CLEANING & CARE
Note:
Oil from the skin will greatly reduce the lifespan of the bulb. If gets on the bulb,
remove the bulb, clean with rubbing alcohol and reinstall.

Solar panel Polycrystalline solar panel 5.5V, 1 Watt
Battery Lithium battery, 18650, 1500mAh, 3.7V, 1PC
Light source
SMD2835 62PCS
(48pcs: 6000k, 14pcs: 3000k
）
Lightness 500LM
Lighting time
Dim Lighting 8 hours, 60minutes
Total lighting after 10 hours fully charged
Lighting
sensitivity 6-8m
Function Dim lighting, sensor lighting
Dim yellow light turns “On” once the time duration is finished
SPECIFICATIONS

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com