Kogan KASTDARIKLA User manual

KOGAN ARIK SWIVEL
TABLETOP TV STAND
(SUITABLE FOR 45” – 65” TVS)
KASTDARIKLA

Read the entire instruction manual before you start installation and assembly. If you have
any questions regarding any of the instructions or warnings, contact your local distributor for
assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and proper tools must be used. This product should only be installed by
professionals.
•Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
•This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
•Never exceed the maximum load capacities of 40kg or it may result in product failure or
personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
SAFETY & WARNINGS

A(x1)
B(x1)
C(x1)
D(x1)
E(x1)
F(x1)
G(x6)
H(x4)
I(x1)
M-A (x4)
M5x14
M-B (x4)
M6x14
M-C (x4)
M6x30
M-D (x4)
M8x30
M-E (x4)
M8x50
M-F (x4)
D5-D8
M-G (x8)
ø15xø8x5
M-H (x8)
ø15xø8x15
P-A (x1)
P-B (x2)
P-C (x1)
P-D (x2)
P-E (x1)
ST4.8x38
P-F (x1)
ø7x35
P-G (x2)
D5
Required for installation (not supplied)
Phillips head
screwdriver Spirit level Stud finder Pencil Drill
COMPONENTS

Step 1
Secure the left and right stand base pieces (B, C) to the main stand (A) with the H screws,
using the supplied Allen key (I) to tighten.
Step 2
Attach the screw cover (F) and feet (G) to the base
MOUNT ASSEMBLY

Step 3
Loosen the main stand’s locking collar and resecure at the desired height for the upper
mounting bracket. Recommended length from the stand edge is 50-150mm.
Note:
•Secure the locking collar (on
the main stand, A) before
attaching TV screen
•Ensure the screw holes face
backwards
Step 4
Remove the screw securing the clip on the lower mounting bracket (E).

Align the upper and lower brackets (D and E) to your TV’s VESA holes and secure using
supplied screws and spacers (“M-” components) depending on required length. Use a
Phillips head screwdriver (not supplied) to secure the screws.
Ensure the anti-toppling safety kit (“P-” components) is in place when fitting the upper
bracket.
Check if additional spacers (M-G, M-H) are required to ensure correct length of screw, as per
the below image. Failure to follow this step may result in damage to your TV or wall mount.
INSTALLING BRACKET TO TV

Place the TV with brackets installed onto the mount stand. Two people should carry the TV
to prevent damage. Once in place, tighten the screw securing the clip on the lower
mounting bracket (E).
Use the openings in the stand assembly for cable management.
SECURING TV TO MOUNT

Pencil, spirit level, stud finder and drill not supplied.
Drywall / plaster:
Using a pencil and spirit level, mark the desired position for the anti-toppling bracket (P-C) on
your wall. Use a stud finder first to check positions of wall studs and ensure the position is
free from electrical wiring. Using a drill, create the pilot hole.
Use a ø3.5mm or 1/8” drill bit, drilling 40mm deep.
TOPPLING FURNITURE WARNING:
•It is strongly recommended that this product is permanently fixed to the wall.
•Please seek professional advice if you are in doubt of what fixing device to use.
•Regularly check that anchors are securely maintained.
•Stability of tall items may be affected by thick carpets or uneven floors.
•Do not place unanchored televisions on furniture.
Caution!
For your safety when attaching the anchor fixings, please note the following:
Check any electrical wires or plumbing inside the wall before drilling any holes (if you
are unsure please seek professional advice from a qualified tradesperson).
FIXING TO WALL

Position the bracket in line with the pilot hole and secure to the wall using screw
(P-E). Do not use the wall anchors.
Thread the cable (P-A) through the cable clips (P-B) and the bracket (P-C). Secure
the fasteners (P-D) using a Phillips head screwdriver.

Masonry / concrete:
Using a pencil and spirit level, mark the desired position for the anti-toppling bracket (P-C) on
your wall. Using a drill, create the pilot hole.
Use a ø7mm or 9/32” drill bit, drilling 40mm deep.
Insert wall anchor (P-F) into the drilled hole. Position the bracket in line with the pilot
hole and secure to the wall using screw (P-E).
Thread the cable (P-A) through the cable clips (P-B) and the bracket (P-C). Secure
the fasteners (P-D) using a Phillips head screwdriver.

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com