Kogan KATVBKSTNDA User manual

SWIVEL TABLETOP STAND
WITH GLASS BASE
FOR 32”-70” TVS
KATVBKSTNDA

Ensure to read all instructions before use and retain this user guide for future reference.
Note the following icon when lifting or moving this unit:
Lifting with two people is recommended at all times.
•Ensure you have located all components before
disposing of any packaging materials.
•This unit is for indoor use only. Use outdoors may result in
product failure, product damage and/or personal injury.
•This unit is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have
been given supervision or instructions concerning use of the appliance by a person
responsible for their safety.
•This unit contains small parts which could pose a choking hazard if swallowed. Keep
away from children.
•Maximum weight capacity for this stand is 40kg.
•Pay close attention to the weight limits. Ensure all connections are secure and that
the screws, brackets, and mounting points on any monitors are in good condition.
•Safety gear and proper tools must be used.
SAFETY & WARNINGS

DIMENSIONS

Parts:
COMPONENTS

Hardware:
A1 (x4)
A2 (x3)
A3 (x3)
A4 (x2)
A5 (x3)
A6 (x4)
A7 (x2)
A8 (x2)
A9 (x2)
A10 (x1)
A11 (x1)
A12 (x2)
M-A (M5x14) (x4)
M-B (M6x14) (x4)
M-C (M6x30) (x4)
M-D (M8x30) (x4)
M-E (M8x50) (x4)
M-F (x4)
M-G (x8)
M-H (x8)
Note:
This assembly requires a Phillips head screwdriver (not supplied).

Step 1:
Add adhesive feet (A1)to the main base (B1).
Step 2:
Fit the end piece (B5)to the stand (B2).
ASSEMBLY

Step 3:
Align the swivel base (B6) with the stand (B2). Using the Allen key (A10), secure with two A4
screws.
Step 4:
Using the Allen key (A10), secure the main base (B1)to the swivel base (B6) using the three
A2 washers, three A3 washers, and three A5 screws. Ensure to not overtighten the screws.

Step 5:
Use the Allen key (A10)to loosen the screws from the stand’s mounting fixture. This will allow
you to set it at your ideal TV height. Once determined, refit the mounting fixture with the
same screws.
Step 6:
Use the spanner (A11)to fit two A9 nuts, and a Phillips head screwdriver
(not supplied) to fit two A7 screws with two A6 washers.

Step 7:
Using a Phillips head screwdriver, secure the support beam (B3)to the
mounting fixture with the A8 screws and A6 washers.
Step 8:
Use a Phillips head screwdriver to remove the locking screws from the two
mounting rails (B4). Keep these screws nearby as they will be required at a later
step.

Step 9a:
Use a Phillips head screwdriver to secure the adapters (M-F) with the appropriate screws
(M-A, M-B), taking note to use the smaller hole on the adapters (M-F).
Note:
To attach the mounting brackets, depending on your TV, refer to either Step 9a
or Step 9b. Ensure the screws fixing the mounting rails to your TV fit correctly.
•If no spacers are needed, follow Step 9a.
•If a combination of spacers (M-G, M-H) are required for a proper fit, follow
Step 9b.

Step 9b:
Secure the adapters (M-F) with the appropriate screws (M-C, M-D, or M-E) using a Phillips
head screwdriver, and the appropriate combination of spacers (M-G, M-H).
Ta k e note to use the larger hole on the adapters (M-F).

Step 10:
Once the mounting rails are securely fitted to your TV, lift your TV (Lifting
with two people is recommended at all times) and align the opening of the
mounting rails (B4) with the support beam (B3).
Fit the two cable management clips (A12)to the stand.
B4
B3

Step 11:
With the TV mounted to the stand, use a Phillips head screwdriver to replace
the locking screws from the mounting rails (see Step 8) to secure the TV.
Use the spanner (A11) to adjust the angle of the mounting fixture.
Use the cable management clips (A12)to secure any cords or cables on your TV.

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com