Kogan KAWLMFX75MA User manual

KOGAN LOW PROFILE FIXED
TV WALL MOUNT
(SUITABLE FOR 32” – 75” TVS)
KAWLMFX75MA

Read the entire instruction manual before you start installation and assembly. If you have
any questions regarding any of the instructions or warnings, contact your local distributor for
assistance.
CAUTION: Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and proper tools must be used. This product should only be installed by
professionals.
•This product is designed to be installed on solid concrete walls, masonry walls or wood
stud walls.
•Make sure that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
•Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
•This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
•Never exceed the maximum load capacity of 45kg or it may result in product failure or
personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
SAFETY & WARNINGS

AWall plate
(x1)
BBrackets
(x2)
M-A Screw
M4 x 14 (x4)
M-B Screw
M5 x 14 (x4)
M-C Screw
M6 x 14 (x4)
M-D Screw
M8 x 15 (x4)
M-E Washer
D5 (x4)
M-F Washer
D8 (x4)
W-A Screw
ST6.3 x 55 (x4)
W-B Wall anchors
ø10 x 45 (x4)
W-C Washer
D6 (x4)
Tools required for installation (not supplied)
Phillips head
screwdriver Spirit level Stud finder Pencil Drill Wrench
COMPONENTS

Step 1
Using a pencil and spirit level, mark the desired position for the mount on your wall, using the
wall mount to serve as a stencil for the hole positions. If mounting on dry wall or plaster-
board, use a stud finder first to check positions of wall studs and ensure the position is free
from electrical wiring. Using a drill, create the pilot holes.
Drywall / plaster: Use a ø4.5mm or 3/16” drill bit, drilling 55mm deep.
Masonry / concrete:Use a ø10mm or 3/8” drill bit, drilling 60mm deep.
Pencil, spirit level, stud finder and drill not supplied.
INSTALLING MOUNT TO WALL

Step 2
Drywall / plaster: Position the wall mount in line with the pilot holes and secure to the wall
using washers (W-C) and ST6.3 screws (W-A). Do not use the wall anchors.
Masonry / concrete:Insert wall anchors (W-B) into the drilled holes. Position the wall mount
in line with the holes and secure to the wall using washers (W-C) and ST6.3 screws (W-A).
When using spirit level, ensure the bubble is centred as per the image
shown here.

Align the brackets with your TV’s VESA holes and secure using supplied screws and washers
depending on required length.
Check if washers (M-E, M-F) are required to ensure correct length of screw, as per the below
image. Failure to follow this step may result in damage to your TV or wall mount.
INSTALLING BRACKET TO TV

Hook the TV with brackets installed onto the wall mount. Two people should carry the TV to
prevent damage.
Once in place, tighten the bracket screws using a Phillips head screwdriver.
SECURING TV TO MOUNT

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com