Kogan KASTTVPB70A User manual

PORTABLE TV MOUNT
STAND CART
(37" - 70")
KASTTVPB70A

CAUTION:
Rated weight for the TV stand is 50kg (110 lbs). The rated weights for the storage shelf
and top rack are 5kg (11 lbs) each.
Use with products heavier than the rated weights indicated may result in instability
causing possible injury.
•Please closely follow the assembly instructions. Improper installation may result in
damage or serious personal injury.
•Safety gear and quality tools must be used.
•When in use, make sure the stand is on a flat level surface and the caster wheels
are locked.
•Do not allow children to play near this stand.
•This product contains small items that could be a choking hazard if swallowed.
Keep these items away from children.
•This product is intended for indoor use only. Using this product outdoors could lead
to product failure and personal injury.
•A minimum of two people are recommended for this installation. Failure to use
safety gear and safe working methods may result in property damage, serious
injury or death.
IMPORTANT: Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of purchase for a
replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at
least every three months).
VESA compatibility:
100x100, 200x100, 200x200, 300x200, 300x300, 400x200, 400x300, 400x400, 600x400
Suitable for TVs 37” – 70” maximum
SAFETY & WARNINGS

Stand assembly:
A(x1)
B(x1)
C(x1)
D(x2)
E(x2)
F(x2)
G(x1)
H(x1)
I(x1)
JRack stand (x1)
KTop rack (x1)
LShelf (x1)
MHole covers (x6)
N(x2)
OM10x35mm (x2)
PM6x35mm (x2)
QM8x60mm (x4)
RM8x12mm (x2)
SM5x8mm (x2)
TWasher (x4)
U(x1)
V5mm (x1)
W8mm (x1)
Adapters (Depends on TV):
M-A M5x14mm (x4)
M-B M6x14mm (x4)
M-C M6x30mm (x4)
M-D M8x30mm (x4)
M-E M8x50mm (x4)
M-F (x4)
M-G (x8)
M-H (x8)
COMPONENTS

Step 1:
Press the locking pin inwards to adjust the mount frame’s (A) adjustable height to Position 1
(as shown below). Repeat this step for both legs of the mount frame, then insert the hole
covers (M) into place.
ASSEMBLY

Step 2:
Clip the front leg attachments (B, C) to the mount frame as shown below. Once clipped into
place, use the 8mm Allen key (W) to secure the M10x35mm screw (O) into place underneath
the frame.
Leave a gap of at least 10mm between the screw and the base of each leg attachment.

Step 3:
Clip the rear leg attachments (D) to the mount frame. Use the 5mm Allen key (V) to secure
the M6x35mm screw (P) at the side of each leg attachment, then use the 8mm Allen key
(W) to finish tightening the M10x35mm screws (O) underneath. Now than both front and rear
leg attachments are in position, the O screws can be secured tightly.

Step 4:
Use the spanner (U) to attach the caster wheels to the end of each leg attachment.
Note the difference between the F (locking) and E (non-locking) casters, and ensure the
locking casters (F) are installed on the front leg attachments (B, C).
Once installed, lock the F casters to avoid any sudden movements during the remainder of
the assembly.
Lock the casters to avoid any
sudden movements during
installation.

Step 5:
Using the 5mm Allen key (V), secure the mounting plate (G) to the frame with the
M8x60mm screws (Q) and washers (T).
Refer to the image below for height options. There are four levels to select from (a, b, c, or d).

Step 6:
Secure the top rack (K) to the rack stand (J) with the M5x8mm screws (S). A screwdriver will
be required for this step (not supplied).
Attach the rack stand to the mounting plate, using the 5mm Allen key (V) to secure the two
M8x12mm screws (R).
The rack stand may be installed at different heights, simply by using different slots. There
are four slots to select from. Do not mix and match different sets of slots, as this may lead to
the rack stand slipping, which may cause damage to your TV and any items on the top rack.