Kogan KASCNCMB51A User manual
Index
I. Unpack Combo Scan II………………….......................................... .2
II. Install film into the film holder…………..…………..….………... .... ..3
III. Quick Start... ..............................................................................6
IV. Operation Guide... ............................................................... ..14
1
II. Install film into the film holder
●Install slide film into the holder entitled “Slides Only”
1. Open the slide holder as illustrated
2. Place slide in recessed slot in holder 3. Close the slide holder
●Install Negative Film into holder entitled “Negative Film Only”
1. Open the film holder as illustrated
3
2. Install film into negative film slot 3. Close the film holder
Note
To avoid mirror image, follow the serial numbers (from left to right) on top of film
when install negative film into holder
If the image is upside down [Figure 2.2], the image can be corrected by pressing
Down/
Flip
button before capturing [Figure 2.3]. Alternative, enter the playback
mode and press Mode button to select Flip function [Figure 2.4]
Figure 2.2
4
Down/Flip button
(Flip hard key)
Flip
●Press hard key on top of device in live view [Figure 2.3]
Playback
button
●Press Playback buttonMode/Setting to select Flip function (Refer to P.25)
[Figure 2.4]
5
III. Quick Start
Power button
Up/Mirror Power status LED
Left/EV Playback
Right/Color Mode/Setting
Down/Flip OK/Capture
SD card slot
Film/Slide slot
Photo/Business
Card slot
Slot for Backlight
holder
Power core port
USB Port
TV out jack
6
How to use Combo Scan II
Scanning Film/Slide
1. Put Film into Film holder, and Insert the film holder into the right side of the unit.
2. Insert the back light holder at the rear side of the unit.
3. Plug in power cable to the power port on the unit and one end to the power outlet
(Figure 3.1).
Figure 3.1
7
4. Press Power button to power on the unit. Enter media type menu to select the correct
media for scanning. (Refer to P.29)
Power
button
Media
Type
5. Press OK/Capture button to capture the image.
OK/Capture
button
6. Press on Playback button to playback the saved images.
Playback
button
8
7. After capturing, take out the SD card which stored the saved images.
8. Alternative to 7, saved picture can be read directly, without taking out the SD card,
from PC by entering MSDC mode. (Refer to P.31)
9
Scanning Photo
1. Remove the film/slide holder as well as the back light holder from the unit if either
one is attached.
Remove film/slide holder by exiting Remove backlight holder by pressing
the sliding to the left hand side. down the handle and pull it out.
2. Open the photo holder frame as illustrated, place the photo on the base of the photo
holder and close the photo holder frame.
10
3. Insert the photo holder into the photo slot of the unit.
4. Enter Media Type Mode to select the correct media for scanning. (Refer to P.29)
Media
Type
5. Press OK/Capture button to capture the image.
OK/Capture
button
11
Scanning Business Card
1. Follow step 1 from scanning photo to remove the film/slide holder as well as the
back light holder in the previous pages.
2. Open the photo holder frame and place the business card on the base of the photo
holder following the engraved guide line.
3. Put the business card fixture on the top of photo holder.
12
4. Insert the photo holder with business card fixture into the photo slot of the unit.
5. Enter media type menu to select the correct media for scanning. (Refer to P.29)
Media
Type
6. Press OK/Capture button to capture the image.
OK/Capture
button
13
IV. Operation Guide
Live View Mode Capture Mode
Playback Mode Setting Mode
14
1. Live View Mode
Live View indicator
(flashing at 0.5sec rate)
After a quick display of welcome page, system will enter the Live View mode. A flashing
red dot appears on the top left hand corner indicating the state in Live View. (Note:
select correct media type (Refer to P.29) before capturing. By default the setting is at
Negative Film. Unit will reset back to the default setting after power off)
1.1 Mirror (Hard Key)
Up/Mirror
Up/Mirror
button
Save & Exit
OK/Capture
●Press Up/Mirror button to turn the image left to right, press again vice versa
15
1.2 Flip (Hard Key)
Save & Exit
Down/Flip OK/Capture
Down/Flip
button
●Press Down/Flip button to turn the image upside down, press again vice versa
1.3 EV (Hard Key)
Up/+
Save & Exit
Left/EV OK/Capture
Down/-
●Press Left/EV button to enter EV(Brightness) control
16
Up/+
button
●Press Up/+ button to increase exposure(brightness) with ranges of -3 to 3
Down/-
button
●Press Down/- button to decrease exposure(brightness) with ranges of -3 to 3
1.4 Color (Hard Key)
Up/+ Save & Exit
Right/Color OK/Capture
Down/-
●Press Right/Color button to enter color control
17
Up/+
button
●Press Up/+ button to increase Color with ranges of -3 to 3
Down/-
button
●Press Down/- button to decrease Color with ranges of -3 to 3
Left/Go Previous Right/Go Next
●Press arrow hard key Left and Right to move between R, G, B
18
2. Capture Mode Right/Go Next
Left/Go Previous OK/Capture mode
Once user presses the OK/Capture hard key, the live view image is selected and wait for
2-3 seconds to enter the Capture mode shown with four icons on the display.
Selected image
Save to Memory Cancel
Rotate +90 Rotate -90
●Save to Memory: save selected image to memory
●Rotate +90: rotate +90 degrees
●Rotate -90: continue rotate -90 degrees
(this is for adjusting images taken in portrait mode)
●Cancel: cancel all action and return to Live View
19
Table of contents
Other Kogan Scanner manuals
