
4
5
7
1141182-X2-E 2
Install The Faucet
To perform installation, installer must
provide G1/2˝ female supply fittings(1),
space 150mm apart and level. The
supply fittings should be vertical and
not beyond the finished wall. Hot supply
pipe must be located on the left.
Install the two offset connectors(2) into
the HOT and COLD supply pipes. Use
appropriate thread sealants or thread
tap on pipe threads.
Adjust the center-to-center distance
between the connectors to 150mm and
level. They should extend 29mm
beyond the finished wall. Thread the
escutcheons(3) onto the connectors
until they are against the finished wall.
Put washers(5) into nuts(4) of the
faucet. Thread the nuts to connectors.
NOTE: When tighten the nuts, use
strap wrench or soft cloth between
product and regular wrench to protect
the finish.
Insert the water flow regulator(9) into
the inlet of the handspray(10). Connect
the faucet outlet(7) and the handspray
with hose(8) and washers(6).
1141182-X2-E 3
INSTALLATION
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off
postion.
Turn on the main water supply, and
check for leaks. Repair as needed.
Bath & Shower Faucet:
Remove the handspray(10) and remove
the aerator(15). Run hot and cold water
through the faucet for about one minute
to remove any debris. Check for leaks.
Remove any debris from the aerator.
Shut off the faucet, and reinstall the
aerator and handspray.
Shower Faucet:
Remove the handspray(10). Run hot
and cold water through the faucet for
about one minute to remove any debris.
Check for leaks. Shut off the faucet,
and reinstall the handspray.
1
2
Cold
Hot
150 mm/
3
CARE AND CLEANING
For best results, keep the following in mind when
caring for your product:
Always test your cleaning solution on an
inconspicuous area before applying to the entire
surface.
Wipe surfaces clean and rinse completely with
water immediately after applying cleaner. Rinse and
dry any overspray that lands on nearby surfaces.
Do not allow cleaners to soak on surfaces.
Use a soft, dampened sponge or cloth. Never use
an abrasive material such as a brush or scouring
pad to clean surfaces.
• The ideal cleaning technique is to rinse thoroughly
and blot dry any water from the surface after each
use.
•
•
•
•
ดาอะสมาวคาํทะลแาษกัรลแูดราก
29mm/
รติดตั้งากบอสดท
Lift the handle gently. Turn clockwise for hot water,
counter-clockwise for cold water.
For 7686X, diverter turns clockwise for shower. Shut
off the faucet, turns counter-clockwise until it stops for
bath spout.
HANDLE OPERATION
9
10
10
15
กยโนากนางชใรากีธิว
6
8
How to Install the Shower
Bracket
Determine a suitable location on the
finished wall to install the bracket. Mark
bracket base mounting hole locations
on the wall according to the dimension.
Drill two holes on the finished wall, the
holes should match the anchors(11).
Install the anchors.
Tighten screws(12) to secure bracket
base(13, flat side upward). Put the
bracket(14) onto the bracket base and
lock by stopper.
27
12
14
13
11
กอนเริ่มการติดตั้ง
การติดตั้งกอกนํ้า
ขอสังเกต:
วิธีติดตั้งขอแขวน
กอกผสมลงอางอาบนํ้าและยืนอาบ
แบบติดผนังพรอมฝกบัวสายออน
กอกผสมยืนอาบแบบติดผนัง
พรอมฝกบัวสายออน
•
•
•
•
•