Komatsu PC200-8 User manual

OPTIONAL EQUIPMENT
●Additional filter system for poor-quality fuel
●Air conditioner with defroster
●Alternator, 60 Ampere, 24 V
●Arms
—2925 mm 9'7" arm assembly
—2410 mm 7'11" arm assembly
—1840 mm 6'0" arm assembly
●Batteries, large capacity
●Bolt-on top guard, [Operator Protective
Guards level 2]
●Boom, 5700 mm 18'8"
●Cab accessories
—Rain visor
—Sun visor
●Cab front guard
—Full height guard
—Half height guard
●Heater with defroster
●Long lubricating intervals for work equip-
ment bushing (500 hours)
●Rear view monitoring system
●Seat belt, retractable
●Seat, suspension
●Service valve
●Shoes, triple grouser
—PC200-8: 500 mm 20",
700 mm 28", 800 mm 31.5"
—PC200LC-8: 600 mm 24",
800 mm 31.5", 900 mm 35.5"
●Track frame undercover
●Track roller guards (full length)
●Working lights
—2 on cab
—1 on counterweight
STANDARD EQUIPMENT
●Alternator, 35 Ampere, 24 V
●Anti-slip plates
●Auto-decel
●Automatic engine warm-up system
●Batteries, 110 Ah/2 x 12 V
●Boom holding valve
●Cab, OPG top guard level 2 capable with
optional bolt-on top guard
●Counterweight
●Dry type air cleaner, double element
●Electric horn
●EMMS monitoring system
●Engine, Komatsu SAA6D107E-1
●Engine overheat prevention system
●Fan guard structure
●Hydraulic track adjusters (each side)
●Multi-function color monitor
●Power maximizing system
●PPC hydraulic control system
●Radiator and oil cooler dust proof net
●Rear reflector
●Rearview mirrors (RH, LH, rear, sidewise)
●Starting motor, 4.5 kW/24 V x 1
●Suction fan
●Track guiding guard, center section
●Track roller
—PC200-8, 7 each side
—PC200LC-8, 9 each side
●Track shoe
—PC200-8, 600 mm 24" triple grouser
—PC200LC-8, 700 mm 28" triple grouser
●Travel alarm
●Working light, 2 (boom and RH)
●Working mode selection system
SPECIAL PURPOSE BUCKET
•Ditch cleaning bucket
—Capacity
SAE heaped 0.80 m31.05 yd3
CECE heaped 0.70 m30.92 yd3
Width 1800 mm 70.9"
•Trapezoidal bucket is ideal for digging
ditches and for drainage works
—Capacity
SAE heaped 0.7 m30.92 yd3
CECE heaped 0.5 m30.65 yd3
•Slope finishing bucket for scraping
slopes of banks
—Capacity
SAE heaped 0.40 m30.52 yd3
CECE heaped 0.35 m30.46 yd3
Width 2000 mm 78.7"
•Ripper bucket for hard and rock ground
—Capacity
SAE heaped 0.62 m30.81 yd3
CECE heaped 0.56 m30.73 yd3
Width 990 mm 39.0"
•Single-shank ripper and three-shank
ripper are recommended for rock-digging
and crushing, hard soil digging, pave-
ment removal works, etc.
www.Komatsu.com
CEN00049-06 Materials and specifications are subject to change without notice.
is a trademark of Komatsu Ltd. Japan.
Printed in Japan 200905 IP.As(10)
FLYWHEEL HORSEPOWER
Gross: 116 kW 155 HP @ 2000 rpm
Net: 110 kW 148 HP @ 2000 rpm
OPERATING WEIGHT
PC200-8: 19400– 20010 kg
42,770– 44,110 lb
PC200LC-8: 20630– 21460 kg
45,480– 47,310 lb
Photo may include optional equipment.
PC200-8
PC200LC-8
PC
200
HYDRAULIC EXCAVATOR

HORSEPOWER
Gross: 116 kW 155 HP @ 2000 rpm
Net: 110 kW 148 HP @ 2000 rpm
OPERATING WEIGHT
PC200-8: 19400 – 20010 kg
42,770 – 44,110 lb
PC200LC-8: 20630 – 21460 kg
45,480 – 47,310 lb
BUCKET CAPACITY
0.50 – 1.17 m3
0.65 – 1.53 yd3
WALK-AROUND
HYDRAULIC EXCAVATOR HYDRAULIC EXCAVATOR
PC200-8
PC200-8 0
32
Large TFT LCD monitor
• Easy-to-see and use 7" large
multi-function color monitor
• Can be displayed in 12 lan-
guages for global support.
TFT : Thin Film Transistor
LCD : Liquid Crystal Display
See page 8.
Large Comfortable Cab
• Low-noise cab, similar to passenger car
• Low vibration with cab damper mounting
• Highly pressurized cab with optional air conditioner
• Operator seat and console with armrest that enables operations in
the appropriate operational posture.
See pages 6.
Ecology and Economy Features
●Low fuel consumption by total
control of the engine, hydraulic
and electronic system.
Reduces fuel consumption by approx. 10%.
(Compared with the PC200-7)
●Low emission engine
A powerful, turbocharged and air-to-air
aftercooled Komatsu SAA6D107E-1 provides
110 kW 148 HP. This engine meets EPA Tier
3 and EU Stage 3A emissions certified, with-
out sacrificing power or machine productivity.
• Economy mode improves fuel consumption.
• Eco-gauge for energy-saving operations
• Extended idling caution for fuel conservation
●Low operation noise
The dynamic noise is lowered by 2 dB compared
with the PC200-7, realizing a low noise operation.
See page 4 and 5.
Easy Maintenance
• Long replacement interval of engine oil, engine oil filter, and
hydraulic filter
• Remote mounted engine oil filter and fuel drain valve for easy
access
• Equipped with the fuel pre-filter as standard (with water separator)
• Side-by-side cooling concept enables individual cooling modules
to be serviced.
• Equipped with the EMMS monitoring system
See page 9.
Photo may include optional equipment.
Safety Design
• Cab dedicated to hydraulic excavator for protecting
the operator in the event of a roll over accident.
• Anti-slip plates for safe work on machine
• Safety enhancement with large side-view, sidewise, and
rear mirrors added.
• Rear view monitoring system for easy checking behind the
machine (optional)
• OPG top guard level 2 capable with optional bolt-on top guard.
See page 7.

Working Modes Selectable
Two established work modes are fur-
ther improved.
P mode – Power or work priority mode
has low fuel consumption, but fast
equipment speed and maximum pro-
duction and power are maintained.
E mode – Economy or fuel priority
mode further reduces fuel consumption,
but maintains the P-mode-like working
equipment speed for light duty work.
You can select Power or Economy
modes using a one-touch operation on
the monitor panel depending on work-
loads.
Eco-gauge that Assists Energy-
saving Operations
Equipped with the Eco-gauge that can
be recognized at a glance on the right of
the multi-function color monitor for envi-
ronment-friendly energy-saving opera-
tions. Allows focus on operation in the
green range with reduced CO2emis-
sions and efficient fuel consumption.
Komatsu Technology
Komatsu develops and produces all major
components, such as engines, electronics
and hydraulic components, in house.
With this “Komatsu Technology,” and adding
customer feedback, Komatsu is achieving
great advancements in technology.
To achieve both high levels of productivity and
economical performance, Komatsu has devel-
oped the main components with a total control
system. The result is a new generation of high
performance and environment-friendly exca-
vators.
4
ECOLOGY & ECONOMY FEATURES
HYDRAULIC EXCAVATOR PC200-8 0
Electronic control
unit for engine
Hydraulic system
controller
Engine
Heavy duty HPCR
(High Pressure
Common Rail)
system
Hydraulic control valve
Flow divide/merge control
with EPC
Main pump
Two pump independent control
Seven-inch TFT liquid crystal display
E
P
Fuel priority
E mode
Work priority
P mode
5
Fuel consumption 10% reduced
Compared with the PC200-7 at P mode and
100% working efficiency.
Fuel consumption varies depending on job
conditions.
Eco-gauge
Low Operation Noise
Enables a low noise operation using the low-noise engine and methods to cut
noise at source.
Idling Caution
To prevent unnecessary fuel consumption, an
idling caution is displayed on the monitor, if the
engine idles for 5 minutes or more.
Low Fuel Consumption
The newly-developed Komatsu
SAA6D107E-1 [ecot3] engine enables
NOx emissions to be significantly
reduced with the accurate multi-staged
fuel injection by the engine controller. It
improves total engine durability using
the high-pressure fuel injection system
developed specifically for construction
machinery. This excavator significantly
reduces hourly fuel consumption using
the highly-efficient matching techniques
of the engine and hydraulic unit and
also provides features that promote
energy-saving operations such as the E
mode and Eco-gauge.
Reduced fan speed
Large capacity radiator
Electronically controlled
common rail type engine
• Multi-staged injection
• Highly rigid cylinder block
Dynamic noise 2dB reduced
(Compared with the PC200-7)
Low-noise muffler
Optimal arrangement
of sound absorbing
materials
HYDRAULIC EXCAVATOR
PC200-8
Low Emission Engine
Komatsu SAA6D107E-1 meets EPA, Tier 3 and EU Stage
3A emissions certified and reduced NOx emission by 29%
compared with the
PC200-7.

76
Low Cab Noise
The newly-designed cab is highly rigid
and has excellent sound absorption
ability. Thorough improvement of noise
source reduction and use of low noise
engine, hydraulic equipment, and air
conditioner allows this machine to gen-
erate a low level of noise similar to
that of a passenger car.
Low Vibration with Cab Damper
Mounting
PC200-8 uses viscous damper mount-
ing for cab that incorporates longer
stroke and the addition of a spring. The
new cab damper mounting combined
with high rigidity deck aids vibration
reduction at operator seat.
Wide Newly-designed Cab
Newly-designed wide spacious cab
includes seat with reclining backrest.
The seat height and longitudinal incli-
nation are easily adjusted using a pull-
up lever. You can set the appropriate
operational posture of armrest together
with the console.
Reclining the seat further enables you
to place it into the fully flat state with
the headrest attached.
Pressurized Cab
Optional air conditioner, air filter and a
higher internal air pressure (+6.0 mm
Aq +0.2"Aq) prevent external dust
from entering the cab.
Automatic Air Conditioner
(optional)
Enables you
to easily and
precisely set
cab atmos-
phere with
the instru-
ments on the large LCD.
The bi-level control function keeps the
operator's head and feet cool and
warm respectively. This improved air
flow function keeps the inside of the
cab comfortable throughout the year.
Defroster function keeps front glass
clear.
Cab Dedicated to Hydraulic Excavator
The cab is designed specifically for hydraulic excavators and
gains reinforced strength from the pipe-structured cab frame-
work. The cab framework provides the high durability and
impact resistance with very high impact absorbency. The
seat belt keeps the operator in the seat of the cab during a
roll over.
Anti-slip Plates
Highly durable anti-
slip plates maintain
superior traction
performance for the
long term.
Pump/engine Room Partition
Pump/engine room partition prevents oil from spraying onto
the engine if a hydraulic hose should burst.
Lock Lever
Locks the hydraulic
pressure to prevent
unintentional move-
ment. Neutral start
function allows
machine to be started
only in lock position.
Large Side-view, Rear, and
Sidewise Mirrors
Enlarged left-side mirror and addition of
rear and side mirror allow the PC200-8
to meet the new ISO visibility require-
ments.
Rear View Monitoring System (optional)
The operator can view the rear of the machine with a color
monitor screen.
Thermal and Fan Guards
Thermal and fan guards
are placed around high-
temperature parts of the
engine and fan drive.
WORKING ENVIRONMENT
HYDRAULIC EXCAVATOR PC200-8 0
Safety Features
Rubber
Silicon
Oil
Spring
HYDRAULIC EXCAVATOR
PC200-8
Monitor for rear view camera

98
Large LCD Color Monitor
Working Mode Application Advantage
Power mode ●Maximum production/power P●Fast cycle time
EEconomy mode ●Excellent fuel economy
LLifting mode ●Hydraulic pressure is
increased by 7%
BBreaker ●Optimum engine rpm,
operation hydraulic flow
ATT Attachment ●Optimum engine rpm,
mode hydraulic flow, 2 way
Side-by-side Cooling
Since radiator, aftercooler and oil cool-
er are arranged in parallel, it is easy to
clean, remove and install them.
Radiator, aftercooler, and oil cooler
made of aluminum have high cooling
efficiency and are easily recycled.
Equipped with the Fuel Pre-filter
(with Water Separator)
Removes water
and contaminants
in the fuel to pre-
vent fuel problems.
(With built-in prim-
ing pump)
Washable Cab Floormat
The PC200-8 's cab floormat is easy
to keep clean. The gently inclined
surface has a flanged floormat
and drainage holes
to facilitate
runoff.
Easy Access to Engine Oil Filter
and Fuel Drain Valve
Engine oil filter and fuel drain valve
are remote mounted to improve
accessibility.
Equipped with the Eco-drain
Valve as Standard.
Prevents clothes and the ground from
becoming contaminated due to oil
leakage when replacing the engine oil.
Large-capacity Fuel Tank and
Rustproof Treatment
400-liter (106 U.S. gal) high-capacity
fuel tank. Effective corro-
sion resistance using rust-
proof treatment.
Sloping Track Frame
Prevents dirt and sand from accumu-
lating and allows easy mud removal.
Gas Assisted Engine Hood
Damper Cylinders
The engine hood can be easily opened
and closed with the assistance of the
gas assisted
engine hood
damper cylin-
ders.
Long-life Oil, Filter
Uses high-performance
filtering materials and
long-life oil. Extends the
oil and filter replacement
interval.
Air Conditioner Filter (optional)
The air conditioner filter is removed
and installed without the use of tools
facilitating filter maintenance.
HYDRAULIC EXCAVATOR PC200-8 0
Mode Selection
The multi-function color monitor has Power mode, Economy
mode, Lifting mode, Breaker mode and Attachment mode.
Lifting Mode
When the Lifting mode is selected, lifting capacity is
increased 7% by raising hydraulic pressure.
MAINTENANCE FEATURES
6
7
8
1
2
3
4
5
1
2
3
4
5
6
Hydraulic oil temperature gauge
Fuel gauge
Eco-gauge
Function switches menu
Auto-decelerator
Working mode
Travel speed
Engine water
temperature gauge
Auto-decelerator
Working mode selector
Traveling selector
Buzzer cancel
Wiper
Windshield washer
Indicators
Basic operation switches
Basic
operation
switches
Air conditioner
operation
switches
Function
switches
8
1 2 3
4 5 6
7
5
6
1 2 3
4
Large Multi-lingual LCD Monitor
A large user-friendly color monitor
enables safe, accurate and smooth work.
Improved screen visibility is achieved by
the use of TFT liquid crystal display that
can easily be read at various angles and
lighting conditions. Simple and easy to
operate switches. Industry first function
keys facilitate multi-function operations.
Displays data in 12 languages to globally
support operators around the world.
Engine oil &
Engine oil filter every 500 hours
Hydraulic oil every 5000 hours
Hydraulic oil filter every 1000 hours
Hydraulic oil filter
(Eco-white element)
Internal air conditioner
filter
External air conditioner
filter
Long Work Equipment Greasing
Interval (optional)
High quality BMRC bushings and resin
shims are optionally available for work
equipment pins excluding bucket,
extending greasing interval to 500
hours.
EMMS
(Equipment Management Monitoring System)
Monitor Function
Controller monitors engine oil
level, coolant temperature, bat-
tery charge and air clogging,
etc. If controller finds any
abnormality, it is displayed on
the LCD.
Maintenance Function
Monitor informs replacement
time of oil and filters on LCD
when the replacement interval
is reached.
Trouble Data Memory
Function
Monitor stores abnormalities for
effective troubleshooting.
HYDRAULIC EXCAVATOR
PC200-8

10
ENGINE
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Komatsu SAA6D107E-1
Type . . . . . . . . . . . . . . . . . . . . Water-cooled, 4-cycle, direct injection
Aspiration. . . . . . . . . . . . . . . . . . . . . . . . . Turbocharged, aftercooled
Number of cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 mm 4.21"
Stroke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 mm 4.88"
Piston displacement. . . . . . . . . . . . . . . . . . . . . . . . . . 6.69 ltr 408 in3
Horsepower:
SAE J1995. . . . . . . . . . . . . . . . . . . . . . . . . Gross 116 kW 155 HP
ISO 9249 / SAE J1349. . . . . . . . . . . . . . . . . . Net 110 kW 148 HP
Rated rpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 rpm
Fan drive method for radiator cooling . . . . . . . . . . . . . . . Mechanical
Governor . . . . . . . . . . . . . . . . . . . . . . . . All-speed control, electronic
EPA Tier 3 and EU Stage 3A emission certified
HYDRAULICS
Type . . HydrauMind (Hydraulic Mechanical Intelligence New Design)
system, closed-center system with load sensing valves and
pressure compensated valves
Number of selectable working modes . . . . . . . . . . . . . . . . . . . . . . . 5
Main pump:
Type . . . . . . . . . . . . . . . . . . . . . Variable displacement piston type
Pumps for . . . . . . . . Boom, arm, bucket, swing, and travel circuits
Maximum flow. . . . . . . . . . . . . . . . . . 439 ltr/min 116 U.S. gal/min
Supply for control circuit . . . . . . . . . . . . . . . . . Self-reducing valve
Hydraulic motors:
Travel. . . . . . . . . . . . . . . 2 x axial piston motor with parking brake
Swing . . . . . . . . . . 1 x axial piston motor with swing holding brake
Relief valve setting:
Implement circuits . . . . . . . . . . . . 37.3 MPa 380 kgf/cm25,400 psi
Travel circuit . . . . . . . . . . . . . . . . 37.3 MPa 380 kgf/cm25,400 psi
Swing circuit . . . . . . . . . . . . . . . . 28.9 MPa 295 kgf/cm24,190 psi
Pilot circuit . . . . . . . . . . . . . . . . . . . . . 3.2 MPa 33 kgf/cm2470 psi
Hydraulic cylinders:
(Number of cylinders – bore x stroke x rod diameter)
Boom . . . . . . 2 – 120 mm x 1334 mm x 85 mm 4.7" x 52.5" x 3.3"
Arm . . . . . . . 1 – 135 mm x 1490 mm x 95 mm 5.3" x 58.7" x 3.7"
Bucket: . . . . . . . . . . . . . . . . for 2.41 m 7'11" and 2.93 m 9'7" Arm
1 – 115 mm x 1120 mm x 80 mm 4.5" x 44.1" x 3.2"
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . for 1.84 m 6'0" Arm
1 – 125 mm x 1110 mm x 85 mm 4.9" x 43.7" x 3.3"
DRIVES AND BRAKES
Steering control . . . . . . . . . . . . . . . . . . . . . . . Two levers with pedals
Drive method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic
Maximum drawbar pull . . . . . . . . . . . . . . 178 kN 18200 kg 40,120 lb
Gradeability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70%, 35°
Maximum travel speed: High . . . . . . . . . . . . . . . . . 5.5 km/h 3.4 mph
(Auto-Shift) Mid. . . . . . . . . . . . . . . . . . 4.1 km/h 2.5 mph
(Auto-Shift) Low . . . . . . . . . . . . . . . . . 3.0 km/h 1.9 mph
Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic lock
Parking brake. . . . . . . . . . . . . . . . . . . . . . . . . Mechanical disc brake
SWING SYSTEM
Drive method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic
Swing reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Planetary gear
Swing circle lubrication . . . . . . . . . . . . . . . . . . . . . . . Grease-bathed
Service brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic lock
Holding brake/Swing lock . . . . . . . . . . . . . . . . Mechanical disc brake
Swing speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4 rpm
UNDERCARRIAGE
Center frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-frame
Track frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Box-section
Seal of track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sealed track
Track adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic
Number of shoes (each side):
PC200-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
PC200LC-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Number of carrier rollers . . . . . . . . . . . . . . . . . . . . . . . . . 2 each side
Number of track rollers (each side):
PC200-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PC200LC-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
COOLANT AND LUBRICANT
CAPACITY (REFILLING)
Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 ltr 105.7 U.S. gal
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.4 ltr 5.4 U.S. gal
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.1 ltr 6.1 U.S. gal
Final drive, each side . . . . . . . . . . . . . . . . . . . . . . 3.3 ltr 0.9 U.S. gal
Swing drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 ltr 1.7 U.S. gal
Hydraulic tank . . . . . . . . . . . . . . . . . . . . . . . . . . 135 ltr 35.7 U.S. gal
OPERATING WEIGHT (APPROXIMATE)
Operating weight including 5700 mm 18'8" one-piece boom,
2925 mm 9'7" arm, SAE heaped 0.80 m31.05 yd3backhoe bucket,
rated capacity of lubricants, coolant, full fuel tank, operator, and
standard equipment.
PC200-8 PC200LC-8
Operating Ground Operating Ground
Shoes Weight Pressure Weight Pressure
500 mm 19400 kg 53.0 kPa
0.54 kgf/cm2——
20" 42,770 lb 7.68 psi
600 mm 19500 kg 45.1 kPa 20630 kg 43.1 kPa
0.46 kgf/cm20.44 kgf/cm2
24" 42,990 lb 6.54 psi 45,480 lb 6.26 psi
700 mm 19750 kg 39.2 kPa 20900 kg 37.3 kPa
0.40 kgf/cm20.38 kgf/cm2
28" 43,540 lb 5.69 psi 46,080 lb 5.40 psi
800 mm 20010 kg 34.3 kPa 21180 kg 33.3 kPa
0.35 kgf/cm20.34 kgf/cm2
31.5" 44,110 lb 4.98 psi 46,690 lb 4.83 psi
900 mm 21460 kg 29.4 kPa
— — 0.30 kgf/cm2
35.5" 47,310 lb 4.27 psi
11
M
G
C
E
H,Q
A
D,L
K
IN
F
O
J
B
P
G.L.
H
F
G
2440(8')
A
B
CED
0
-1
-2
-3
-4
-5
-6
-7
0123456789 10
5
6
7
8
9
10
11
12
11
(m)
1
2
3
4
(m)
Bucket Capacity
Number
(heaped) Width Weight Arm Length
SAE, PCSA CECE Without Side Cutters With Side Cutters With Side Cutters of Teeth 1.84 m 6'0" 2.41 m 7'11" 2.93 m 9'7"
0.50 m3 0.65 yd30.45 m30.59 yd3750 mm 29.5" 875 mm 34.4" 478 kg 1,050 lb 3 
0.80 m31.05 yd30.70 m30.92 yd31045 mm 41.1" 1170 mm 46.1" 635 kg 1,400 lb 5 
0.93 m31.22 yd30.80 m31.05 yd31200 mm 47.2" 1325 mm 52.2" 696 kg 1,530 lb 5 □□ 
1.05 m31.37 yd30.90 m31.18 yd31330 mm 52.4" 1455 mm 57.3" 757 kg 1,670 lb 6 □□ X
1.17 m31.53 yd31.00 m31.31 yd31450 mm 57.1" — 940 kg 2,070 lb 6  X
Arm 1840 mm 6'0" 2410 mm 7'11" 2925 mm 9'7"
AMax. digging height 9500 mm 31'2" 9800 mm 32'2" 10000 mm 32'10"
BMax. dumping height 6630 mm 21'9" 6890 mm 22'7" 7110 mm 23'4"
CMax. digging depth 5380 mm 17'8" 6095 mm 20'0" 6620 mm 21'9"
DMax. vertical wall
digging depth 4630 mm 15'2" 5430 mm 17'10" 5980 mm 19'7"
EMax. digging depth
of cut for 8' level 5130 mm 16'0" 5780 mm 19'0" 6370 mm 20'11"
FMax. digging reach 8850 mm 29'1" 9380 mm 30'9" 9875 mm 32'5"
GMax. digging reach
at ground level 8660 mm 28'5" 9190 mm 30'2" 9700 mm 31'10"
HMin. swing radius 3010 mm 9'11" 3090 mm 10'2" 3040 mm 10'0"
Bucket digging force 157 kN 138 kN 138 kN
at power max. 16000 kgf/35,270 lb 14100 kgf/31,080 lb 14100 kgf/31,080 lb
Arm crowd force 139 kN 124 kN 101 kN
at power max. 14200 kgf/31,300 lb 12600 kgf/27,780 lb 10300 kgf/22,710 lb
Bucket digging force 177 kN 149 kN 149 kN
at power max. 18000 kgf/39,680 lb 15200 kgf/33,510 lb 15200 kgf/33,510 lb
Arm crowd force 145 kN 127 kN 108 kN
at power max. 14800 kgf/32,630 lb 13000 kgf/28,660 lb 11000 kgf/24,250 lb
Arm Length 1840 mm 6'0" 2410 mm 7'11" 2925 mm 9'7"
AOverall length 9480 mm 31'1" 9495 mm 31'2" 9425 mm 30'11"
BLength on ground (transport): PC200-8 6270 mm 20'7" 5700 mm 18'8" 4815 mm 15'10"
PC200LC-8 6455 mm 21'2" 5885 mm 19'4" 5000 mm 16'5"
COverall height (to top of boom) 2985 mm 9'10" 3190 mm 10'6" 2970 mm 9'9"
WORKING RANGE
DIMENSIONS
: General purpose use, density up to 1.8 ton/m31.52 U.S. ton/yd3: Light duty work, density up to 1.2 ton/m31.01 U.S. ton/yd3
□: General purpose use, density up to 1.5 ton/m31.26 U.S. ton/yd3X: Not usable
BACKHOE BUCKET, ARM, AND BOOM COMBINATION
ISO rating SAE rating
PC200-8 PC200LC-8
DOverall width 2800 mm 9'2" 3080 mm 10'1"
EOverall height (to top of cab) 3040 mm 10'0" 3040 mm 10'0"
FGround clearance, counterweight 1085 mm 3'7" 1085 mm 3'7"
GGround clearance (minimum) 440 mm 1'5" 440 mm 1'5"
HTail swing radius 2750 mm 9'0" 2750 mm 9'0"
ITrack length on ground 3275 mm 10'9" 3655 mm 12'0"
JTrack length 4070 mm 13'4" 4450 mm 14'7"
KTrack gauge 2200 mm 7'3" 2380 mm 7'10"
LWidth of crawler 2800 mm 9'2" 3080 mm 10'1"
MShoe width 600 mm 24" 700 mm 28"
NGrouser height 26 mm 1.0" 26 mm 1.0"
OMachine cab height 2095 mm 6'10" 2095 mm 6'10"
PMachine cab width 2710 mm 8'11" 2710 mm 8'11"
QDistance, swing center to rear end 2710 mm 8'11" 2710 mm 8'11"
SPECIFICATIONS
HYDRAULIC EXCAVATOR PC200-8 0
HYDRAULIC EXCAVATOR
PC200-8

LIFTING CAPACITY WITH LIFTING MODE
A: Reach from swing center
B: Bucket hook height
C: Lifting capacity
Cf: Rating over front
Cs: Rating over side
: Rating at maximum reach
Conditions:
●5700 mm 18'8" one-piece boom
●0.8 m3 1.05 yd3SAE heaped bucket
●Shoe width:
—PC200LC-8 700 mm 28" triple
grouser
13
* Load is limited by hydraulic capacity rather than tipping. Ratings are based on SAE Standard No. J1097. Rated loads do not exceed 87% of hydraulic lift
capacity or 75% of tipping load.
LIFTING CAPACITY WITH LIFTING MODE
A: Reach from swing center
B: Bucket hook height
C: Lifting capacity
Cf: Rating over front
Cs: Rating over side
: Rating at maximum reach
Conditions:
●5700 mm 18'8" one-piece boom
●0.8 m3 1.05 yd3SAE heaped bucket
●Shoe width:
—PC200-8 600 mm 24" triple grouser
12
* Load is limited by hydraulic capacity rather than tipping. Ratings are based on SAE Standard No. J1097. Rated loads do not exceed 87% of hydraulic lift
capacity or 75% of tipping load.
PC200-8 Arm: 2925 mm 9'7" Bucket: 0.8 m3 1.05 yd3SAE heaped Shoe: 600 mm 24” triple grouser
AMAX 7.6 m 25' 6.1 m 20' 4.6 m 15' 3.0 m 10' 1.5 m 5'
BCf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
7.6 m *2750 kg *2750 kg *3800 kg *3800 kg
25' *6,100 lb *6,100 lb *8,300 lb *8,300 lb
6.1 m *2600 kg *2600 kg *4300 kg 4050 kg
20' *5,800 lb *5,800 lb *9,500 lb 8,900 lb
4.6 m *2650 kg 2150 kg 3950 kg 2600 kg *4900 kg 3900 kg
15' *5,800 lb 4,800 lb 8,800 lb 5,700 lb *10,800 lb 8,600 lb
3.0 m *2800 kg 1950 kg 3850 kg 2500 kg 5650 kg 3700 kg *7350 kg 5850 kg *11350 kg *11350 kg
10' *6,100 lb 4,300 lb 8,500 lb 5,500 lb 12,500 lb 8,100 lb *16,200 lb 12,900 lb *25,000 lb *25,000 lb
1.5 m 3000 kg 1850 kg 3750 kg 2350 kg 5400 kg 3450 kg 8600 kg 5350 kg *7500 kg *7500 kg
5' 6,600 lb 4,100 lb 8,300 lb 5,200 lb 11,900 lb 7,600 lb 19,000 lb 11,800 lb *16,500 lb *16,500 lb
O m 3050 kg 1900 kg 3650 kg 2300 kg 5200 kg 3250 kg 8250 kg 5050 kg *8000 kg *8000 kg
0' 6,700 lb 4,200 lb 8,000 lb 5,000 lb 11,500 lb 7,200 lb 18,200 lb 11,100 lb *17,700 lb *17,700 lb
–1.5 m 3350 kg 2050 kg 3600 kg 2250 kg 5100 kg 3150 kg 8100 kg 4900 kg *11200 kg 9500 kg *6800 kg *6800 kg
–5' 7,400 lb 4,600 lb 7,900 lb 4,900 lb 11,200 lb 7,000 lb 17,900 lb 10,800 lb *24,700 lb 20,900 lb *15,000 lb *15,000 lb
–3.0 m 4000 kg 2500 kg 5100 kg 3150 kg 8100 kg 4950 kg *15600 kg 9650 kg *10550 kg *10550 kg
–10' 8,800 lb 5,500 lb 11,200 lb 7,000 lb 17,900 lb 10,900 lb *34,400 lb 21,300 lb *23,200 lb *23,200 lb
–4.6 m 5650 kg 3550 kg 8300 kg 5100 kg *13050 kg 10000 kg
–15' 12,500 lb 7,900 lb 18,300 lb 11,200 lb *28,800 lb 22,000 lb
PC200-8 Arm: 2410 mm 7'11" Bucket: 0.8 m3 1.05 yd3SAE heaped Shoe: 600 mm 24” triple grouser
AMAX 7.6 m 25' 6.1 m 20' 4.6 m 15' 3.0 m 10' 1.5 m 5'
BCf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
7.6 m *4300 kg 4300 kg
25' *9,500 lb 9,400 lb
6.1 m *4100 kg 3000 kg *4850 kg 3950 kg
20' *9,000 lb 6,600 lb *10,700 lb 8,700 lb
4.6 m 3800 kg 2450 kg 3900 kg 2500 kg *5400 kg 3800 kg *6200 kg *6200 kg
15' 8,400 lb 5,400 lb 8,600 lb 5,600 lb *11,900 lb 8,400 lb *13,600 lb *13,600 lb
3.0 m 3400 kg 2150 kg 3800 kg 2450 kg 5600 kg 3600 kg *8100 kg 5700 kg
10' 7,500 lb 4,800 lb 8,400 lb 5,400 lb 12,300 lb 8,000 lb *17,800 lb 12,600 lb
1.5 m 3300 kg 2050 kg 3700 kg 2350 kg 5350 kg 3400 kg 8450 kg 5250 kg
5' 7,300 lb 4,600 lb 8,200 lb 5,200 lb 11,800 lb 7,500 lb 18,700 lb 11,500 lb
O m 3400 kg 2100 kg 3650 kg 2250 kg 5150 kg 3250 kg 8150 kg 4950 kg *7350 kg *7350 kg
0' 7,500 lb 4,700 lb 8,000 lb 5,000 lb 11,400 lb 7,100 lb 18,000 lb 11,000 lb *16,200 lb *16,200 lb
–1.5 m 3750 kg 2350 kg 5100 kg 3150 kg 8100 kg 4900 kg *12250 kg 9500 kg *7650 kg *7650 kg
–5' 8,300 lb 5,200 lb 11,200 lb 7,000 lb 17,800 lb 10,800 lb *27,000 lb 21,000 lb *16,900 lb *16,900 lb
–3.0 m 4650 kg 2900 kg 5150 kg 3200 kg 8200 kg 4950 kg *14700 kg 9750 kg *12650 kg *12650 kg
–10' 10,200 lb 6,400 lb 11,400 lb 7,100 lb 18,000 lb 11,000 lb *32,400 lb 21,500 lb *27,900 lb *27,900 lb
–4.6 m *7200 kg 4550 kg *8100 kg 5200 kg *11600 kg 10150 kg
–15' *15,900 lb 10,000 lb *17,800 lb 11,500 lb *25,500 lb 22,400 lb
PC200-8 Arm: 1840 mm 6'0" Bucket: 0.8 m3 1.05 yd3SAE heaped Shoe: 600 mm 24” triple grouser
AMAX 7.6 m 25' 6.1 m 20' 4.6 m 15' 3.0 m 10' 1.5 m 5'
BCf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
7.6 m *4800 kg *4800 kg *5500 kg *5500 kg
25' *10,600 lb *10,600 lb *12,100 lb *12,100 lb
6.1 m *4450 kg 3450 kg *5450 kg 3800 kg *5700 kg *5700 kg
20' *9,900 lb 7,600 lb *12,100 lb 8,300 lb *12,600 lb *12,600 lb
4.6 m 4200 kg 2700 kg 5650 kg 3700 kg *7000 kg 6000 kg *9850 kg *9850 kg
15' 9,300 lb 6,000 lb 12,500 lb 8,100 lb *15,400 lb 13,200 lb *21,800 lb *21,800 lb
3.0 m 3750 kg 2350 kg 5450 kg 3500 kg 8600 kg 5350 kg
10' 8,300 lb 5,200 lb 12,000 lb 7,700 lb 19,000 lb 11,800 lb
1.5 m 3600 kg 2250 kg 3650 kg 2300 kg 5250 kg 3300 kg 8250 kg 5000 kg
5' 8,000 lb 5,000 lb 8,100 lb 5,000 lb 11,500 lb 7,300 lb 18,200 lb 11,100 lb
O m 3750 kg 2300 kg 5100 kg 3150 kg 8050 kg 4850 kg
0' 8,200 lb 5,100 lb 11,200 lb 7,000 lb 17,700 lb 10,700 lb
–1.5 m 4200 kg 2650 kg 5050 kg 3150 kg 8050 kg 4850 kg *13350 kg 9500 kg
–5' 9,300 lb 5,800 lb 11,200 lb 6,900 lb 17,700 lb 10,700 lb *29,400 lb 21,000 lb
–3.0 m 5500 kg 3450 kg 8200 kg 5000 kg *13200 kg 9800 kg
–10' 12,100 lb 7,600 lb 18,100 lb 11,000 lb *29,100 lb 21,600 lb
PC200LC-8 Arm: 2925 mm 9'7" Bucket: 0.8 m3 1.05 yd3SAE heaped Shoe: 700 mm 28” triple grouser
AMAX 7.6 m 25' 6.1 m 20' 4.6 m 15' 3.0 m 10' 1.5 m 5'
BCf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
7.6 m *2750 kg *2750 kg *3800 kg *3800 kg
25' *6,100 lb *6,100 lb *8,300 lb *8,300 lb
6.1 m *2600 kg *2600 kg *4300 kg *4300 kg
20' *5,800 lb *5,800 lb *9,500 lb *9,500 lb
4.6 m *2650 kg 2550 kg *4650 kg 3000 kg *4900 kg 4500 kg
15' *5,800 lb 5,600 lb *10,300 lb 6,600 lb *10,800 lb 9,900 lb
3.0 m *2800 kg 2300 kg 4750 kg 2900 kg *5850 kg 4250 kg *7350 kg 6750 kg *11350 kg *11350 kg
10' *6,100 lb 5,100 lb 10,500 lb 6,400 lb *12,900 lb 9,400 lb *16,200 lb 14,900 lb *25,000 lb *25,000 lb
1.5 m *3050 kg 2200 kg 4650 kg 2800 kg 6700 kg 4000 kg *9300 kg 6250 kg *7500 kg *7500 kg
5' *6,700 lb 4,900 lb 10,200 lb 6,200 lb 14,700 lb 8,900 lb *20,500 lb 13,800 lb *16,500 lb *16,500 lb
O m *3500 kg 2250 kg 4550 kg 2700 kg 6450 kg 3850 kg 10450 kg 5900 kg *8000 kg *8000 kg
0' *7,800 lb 5,000 lb 10,000 lb 5,900 lb 14,300 lb 8,400 lb 23,000 lb 13,000 lb *17,700 lb *17,700 lb
–1.5 m 4150 kg 2450 kg 4500 kg 2650 kg 6350 kg 3750 kg *10250 kg 5800 kg *11200 kg *11200 kg *6800 kg *6800 kg
–5' 9,200 lb 5,400 lb 9,900 lb 5,800 lb 14,000 lb 8,200 lb *22,700 lb 12,700 lb *24,700 lb *24,700 lb *15,000 lb *15,000 lb
–3.0 m 4950 kg 2950 kg 6350 kg 3750 kg 10300 kg 5800 kg *15600 kg 11500 kg *10550 kg *10550 kg
–10' 11,000 lb 6,500 lb 14,000 lb 8,200 lb 22,700 lb 12,800 lb *34,400 lb 25,400 lb *23,200 lb *23,200 lb
–4.6 m *6750 kg 4150 kg *9050 kg 6000 kg *13050 kg 11900 kg
–15' *14,900 lb 9,200 lb *20,000 lb 13,200 lb *28,800 lb 26,200 lb
PC200LC-8 Arm: 2410 mm 7'11" Bucket: 0.8 m3 1.05 yd3SAE heaped Shoe: 700 mm 28” triple grouser
AMAX 7.6 m 25' 6.1 m 20' 4.6 m 15' 3.0 m 10' 1.5 m 5'
BCf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
7.6 m *4300 kg *4300 kg
25' *9,500 lb *9,500 lb
6.1 m *4100 kg 3500 kg *4850 kg 4500 kg
20' *9,000 lb 7,700 lb *10,700 lb 10,000 lb
4.6 m *4150 kg 2850 kg *4700 kg 2950 kg *5400 kg 4400 kg *6200 kg *6200 kg
15' *9,100 lb 6,300 lb *10,400 lb 6,500 lb *11,900 lb 9,700 lb *13,600 lb *13,600 lb
3.0 m *4250 kg 2550 kg 4700 kg 2850 kg *6300 kg 4200 kg *8100 kg 6600 kg
10' *9,300 lb 5,600 lb 10,400 lb 6,300 lb *13,900 lb 9,200 lb *17,800 lb 14,600 lb
1.5 m 4100 kg 2450 kg 4600 kg 2750 kg *6600 kg 3950 kg *9850 kg 6100 kg
5' 9,000 lb 5,400 lb 10,200 lb 6,100 lb *14,500 lb 8,700 lb *21,800 lb 13,500 lb
O m 4200 kg 2500 kg 4550 kg 2700 kg 6450 kg 3800 kg 10350 kg 5850 kg *7350 kg *7350 kg
0' 9,300 lb 5,500 lb 10,000 lb 5,900 lb 14,200 lb 8,400 lb 22,800 lb 12,900 lb *16,200 lb *16,200 lb
–1.5 m 4650 kg 2750 kg 6350 kg 3750 kg 10250 kg 5800 kg *12250 kg 11400 kg *7650 kg *7650 kg
–5' 10,300 lb 6,100 lb 14,000 lb 8,300 lb 22,600 lb 12,700 lb *27,000 lb 25,100 lb *16,900 lb *16,900 lb
–3.0 m 5750 kg 3450 kg 6400 kg 3800 kg *10250 kg 5850 kg *14700 kg 11600 kg *12650 kg *12650 kg
–10' 12,700 lb 7,600 lb 14,200 lb 8,400 lb *22,600 lb 12,900 lb *32,400 lb 25,600 lb *27,900 lb *27,900 lb
–4.6 m *7200 kg 5300 kg *8100 kg 6100 kg *11600 kg *11600 kg
–15' *15,900 lb 11,700 lb *17,800 lb 13,500 lb *25,500 lb *25,500 lb
PC200LC-8 Arm: 1840 mm 6'0" Bucket: 0.8 m3 1.05 yd3SAE heaped Shoe: 700 mm 28” triple grouser
AMAX 7.6 m 25' 6.1 m 20' 4.6 m 15' 3.0 m 10' 1.5 m 5'
BCf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
7.6 m *4800 kg *4800 kg *5500 kg *5500 kg
25' *10,600 lb *10,600 lb *12,100 lb *12,100 lb
6.1 m *4450 kg 3950 kg *5450 kg 4350 kg *5700 kg *5700 kg
20' *9,900 lb 8,800 lb *12,100 lb 9,600 lb *12,600 lb *12,600 lb
4.6 m *4500 kg 3150 kg *5900 kg 4250 kg *7000 kg 6900 kg *9850 kg *9850 kg
15' *9,900 lb 7,000 lb *13,000 lb 9,400 lb *15,400 lb 15,200 lb *21,800 lb *21,800 lb
3.0 m *4650 kg 2800 kg *6700 kg 4050 kg *8700 kg 6250 kg
10' *10,200 lb 6,200 lb *14,800 lb 9,000 lb *19,200 lb 13,700 lb
1.5 m 4500 kg 2650 kg 4550 kg 2700 kg 6500 kg 3850 kg *10350 kg 5900 kg
5' 9,900 lb 5,900 lb 10,000 lb 6,000 lb 14,300 lb 8,500 lb *22,800 lb 13,000 lb
O m 4650 kg 2750 kg 6350 kg 3750 kg 10200 kg 5700 kg
0' 10,300 lb 6,100 lb 14,000 lb 8,200 lb 22,500 lb 12,600 lb
–1.5 m 5250 kg 3100 kg 6350 kg 3700 kg 10200 kg 5700 kg *13350 kg 11350 kg
–5' 11,600 lb 6,900 lb 14,000 lb 8,200 lb 22,500 lb 12,600 lb *29,400 lb 25,100 lb
–3.0 m 6850 kg 4050 kg *9550 kg 5900 kg *13200 kg 11700 kg
–10' 15,100 lb 8,900 lb *21,100 lb 13,000 lb *29,100 lb 25,800 lb
A
B
C
A
B
C