Komfovent DOMEKT ReGO 200VE-B Manual

DOMEKT REGO 200VE(W)-B(K)
Series Air Handling Units Installation
and Maintenance Service Manual
EN

2
Content
Safety Requirements ..................................................................................3
Transportation ..................................................................................3
Brief Description of the Unit ..................................................................................5
Installation ..................................................................................6
Checking of unit elements ..................................................................................7
Maintenance ............................................................................... 10
Technical Information ............................................................................... 12
Ordering Key ................................................................................14
We reserve the right to make changes without prior notice.
This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC)
and your national law. This product should be handed over to a designated collection point, or to an authorised collection site for recycling
waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a possible negative impact on the
environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your
cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about
where you can drop off your waste equipment for recycling, please contact your local city ofce, waste authority, approved WEEE scheme
or your household waste disposal service.

3
Safety Requirements
• To avoid accidents and/or unit damage, only a trained technician must carry
out the connection.
• The appropriate Personal Protective Equipment (PPE) attire is worn relative to
the operation being carried out.
• Electrical equipment is rated, connected and earthed in accordance with CE
regulations.
The air handling unit must be plugged in to an electrical outlet (with earth), which is in good order and
corresponds with all requirements of electric safety.
Before starting any operations inside the unit, make sure that the unit is switched off, and the power cable is
unplugged.
• Earth must be installed according EN61557, BS 7671
• The unit should be installed according to Installation and Maintenance Manual.
• Before starting the unit, check correct position of air lters.
• Service maintenance should be carried out only in conformity with the instruc-
tions specied herein below.
• If main cable is damaged, only manufacturer, service team or trained technician
must change it in order to avoid accidents.
Transportation
The air handling units are ready for transit and storage (1 a, b Pictures). The unit is packed to prevent damage
of the external and internal parts of the unit, dust and moisture penetration.
The unit is packed to box after that corners of the air handling units are protected against the damage – protective
corners are used. The entire unit is wrapped up in protective lm. For transit or storage, units are mounted on
timber pallets. The unit is fastened to the pallet with polypropylene packing tape.
Air handling units ready for transit and storage
1 a Units ready for transit and storage without kitchen hood
1 b Units ready for transit and storage with kitchen hood.
We reserve the right to make changes without prior notice.
Installation and Maintenance Service Manual
1 b Picture
1 a Picture

4
When unit is loaded or unloaded by crane, cargo rope is fastened in its designated places.
Forklift truck or hand pallet truck can transport air handling unit as it is shown (2 a, b Pictures).
Unit transportation by forklift truck or hand pallet truck
2a Unit is transported by hand pallet truck on a wooden pallet
2b Unit is transported by forklift truck on a wooden pallet
The unit should be examined upon receipt, to ensure that no visible damage has occurred during transit, and the
advice note checked to ensure that all items have been received. If damage or delivery shortages are discovered,
the carrier should be immediately informed. AMALVA should be notied within three days of receipt, with a written
conrmation sent within seven days. AMALVA can accept no responsibility for damage by unloading from carrier
or for subsequent damage on site.
If the unit is not to be installed immediately, it should be stored in a clean, dry area. If stored externally, it should
be adequately protected from the weather.
Installation and Maintenance Service Manual
2 b Picture
2 a Picture
We reserve the right to make changes without prior notice.

5
Installation and Maintenance Service Manual
A. Outdoor intake
B. Supply air
C. Extract indoor
D. Exhaust air
E. Kitchen hood connection (by-pass – extraction without heat recovery)
F. Bathroom connection (by-pass – extraction with out heat recovery)
E
F
3 Picture
We reserve the right to make changes without prior notice.
Brief Description of the Unit
• Casings of air handling units are made of galvanized steel sheets, which are powder painted. Mineral wool is used
for thermal insulation and sound attenuation. Unit cover panels are 15...20 mm thick. The air handling unit is in-
tended for ventilation of small-sized spaces (eg. single family houses, ats). The unit is designed to be mounted on
kitchen hood. As standard, the unit is designed for indoor placement. The operating temperature range for the unit
is -300C ... 400C, outdoor air temperature.
The air handling unit is not to be used to transport solid particles, even not in areas where there is a risk of
explosive gases.
• KOMFOVENT DOMEKT REGO 200VE(W) is equipped with a rotary heat exchanger, air lters, an electric air
heater, fans and automation control system, to ensure safe and efcient operation of the unit.
• Before you open the door, the unit must be switched off and the fans must have been given time to stop (up to 3
minutes).
• The unit contains heating elements that must not be touched when they are hot.
• To maintain a good indoor climate, comply with regulations and, to avoid condensation damage, the unit must never
be stopped apart from during service/maintenance or in connection with an accident.
• If the unit is placed in spaces with high humidity, condensation might occur on the surface of the unit when outdoor
temperatures are very low.
DOMEKT REGO 200VE(W) B(K) Air Handling Unit Schemes
1. Rotary heat exchanger
2. Supply air lter
3. Exhaust air lter
4. Supply fan
5. Exhaust fan
6. Electric air heater*
7. Automation control system
* AHU REGO-200VW-B is suitable for use with water duct air heater.
Note: The appropriate sound attenuators mounted together with supply air ducts will reduce the noise level of the fans in the premises.
2
7
6
4
E
A
B
3
5
1
F
D
C
4
6
7
3
2
5
B
A
F
D
C
E
1
BAB
C AF DFDC
E E

6
Installation and Maintenance Service Manual
Installation
Before installing the unit, inspection must be carried out. From the front ant back, unit have removable doors.
The components inside unit are removable from both sides. In the picture 4 are shown the units of left inspec-
tion side. To have the unit of right inspection side, it is necessary replace position of the doors due to hanging the
furniture or decorative panel (see picture 6).
Inslallation of kitchen hood
Air handling unit is mounted on the kitchen hood.
Kitchen hood
1. REGO 200VE(W)
2. Kitchen hood
3. Screw for hood connection (srew M4x16 base in set of unit)
4 Picture
5 Picture
We reserve the right to make changes without prior notice.
1
2
3

7
8
E
D
A
1
2
3
4
5
6
7
D
E
A
Installation and Maintenance Service Manual
6 Picture
We reserve the right to make changes without prior notice.
Unit hanging scheme
View E: Brackets for hanging the furniture or decorative panel.
Marking Description REGO 200VE(W)-BK-
AC/EC-C4-F/ pcs.
1 Wall plug KWP (nylon) 8x50 + screw 4,5x50 5
2REGO 200VE-00.014 Mounting bracket 1
3REGO 200VE-00.011 Unit bracket 1
4Self tapping screw 4,2x13 16
5 Wall plug KWP (nylon) 6x35 + screw 3,5x35 2
6 Bracket for front cover 4260-2.293 Z (AGVA) 4
7 Screw 2.5x16 ZnG with cone head 16
8Screw M4x16 for kitchen hood connection 4

8
Installation and Maintenance Service Manual
We reserve the right to make changes without prior notice.
Unit hanging scheme without kitchen hood
View C: Brackets for hanging the furniture or decorative panel.
Marking Description REGO 200VE(W)-B-
AC/EC-C4-F/ pcs.
1 REGO 200VE-00.014 Mounting bracket 1
2Wall plug KWP (nylon) 8x50 + screw 9
3REGO 200VE-00.011 Unit bracket 1
4Self tapping screw 4,2x13 16
5 REGO 200VE-00.015 Bracket 1
6REGO 200VE-00.016 Bracket 1
7 M6 (DIN 125 A) Washer 6
8M 4x16 (DIN 7985) Screw
9 Bracket for front cover 4260-2.293 Z (AGVA) 2
10 Screw 2.5x16 ZnG with cone head 16
7 Picture
2
1
3
4
7
5
8
7
9
10
A
C
A
B
B
C
6

9
8 Picture
Installation and Maintenance Service Manual
We reserve the right to make changes without prior notice.
The dimensions of suspended furniture panel
The dimensions of the place of the REGO 200VE(W) suspended
9 a Picture
140
140x4=560
575
600
22
625
600
500
250
22
32.5
500
250
32.5
O 2(depth - 5 mm) 16 holes

10
Final Inspection
After installation of the unit, a thorough inspection should be carried out. This should include inspecting the
inside of the unit and removing debris and tools, which may have been left behind by on site contractors. Replace
any panels, which may have been removed and close all access doors, ensuring that the door sealing gaskets
have not been damaged.
Maintenance
It is recommended to carry out routine maintenance of the air handling unit KOMFOVENT DOMEKT
REGO 200VE(W) 3 – 4 times per year.
All components inside the unit are easily detachable for cleaning. Don’t forget to unplug the cables out of
electric components and unscrew bolts from electric heater and rotary heat exchanger.
Unscrew
Installation and Maintenance Service Manual
10 b Picture
We reserve the right to make changes without prior notice.
Pull
Unscrew
500
320
42
804
625
~777
3
2
1
4
5
10 a Picture
1. Screw
2. Wall plug
3. Hanging bracket 1
4. Hanging bracket 2
5. Gasket 9 b Picture