Koncept UCX Pro Series User manual

The UCX Pro can be mounted onto a wood or steel surface.
Steel surface
Secure the mounts to the surface
using provided screws.
Snap-fit the light to the mounts. Snap-fit the mounts to
the groove on the back
of the light.
Aach to a steel surface.
Wood surface
OR
Oponal/Sold separately: Daisy chain or male to male connector(s)
Plug a daisy-chain cable* into either end of the luminaire to power an addional
unit. If you are powering mulple units, connect them with daisy chain cables as
illustrated.
Mulple units require sufficient power output. Please refer to the power chart on
the back of this manual.
daisy-chain cable*
*sold separately
UCX Pro undercabinet light
Assembly Instrucons
Connect power supplyLAST aer all components,luminaires anddaisy-chained cables have been connected.
DO NOT live connect powered components or luminaire units.
STOP
DONOT CONNECT POWERYET
male-to-male connector*

Aer any occupancy sensor, wifi module and connectors have been inserted, plug the
power supply into the large socket at either end of the light.
wifi module*
GROUP mode: Sync’ed brightness levels and light color with all
connected UCX Pros. Controllable by occupancy sensor or WiFi module.
SINGLE mode: Independent of any connected UCX Pros or sensors.
LED signal lights indicate whether the light is in
GROUP or SINGLE mode
Touch and hold the MODE buon to
switch between GROUP or SINGLE mode
Hold to switch between warm/cool
When OFF:
When ON:
Slide your finger along the
touchstrip to control
brightness/on/off.
power supply cable
UCX Pro undercabinet light
Assembly Instrucons
Warnings
Model
Color Temperature
Brightness Adjustability built-in touchstrip
Light Color
Koncept Inc.
429 E. Hunngton Drive
Monrovia, CA 91016
Phone: [phone]
Fax: [phone]
[email protected]om
www.koncept.com
Specificaons
Model UCX-19 UCX-27 UCX-37
System Power 10.5 W 15.5 W 22.5 W
Luminaire Waage 8.64 W 13 W 18.7 W
Power consumpon:
Model UCX-19 UCX-27 UCX-37
24V 1A transformer* 2 units 1 unit 1 unit
24V 2A transformer 4 units 3 units 2 units
Maximum connected units supported:
*standard transformer provided
OVERHEATING MAY RESULT IN REDUCED LED LIFESPAN. TO AVOID OVERHEATING:
• Keep out of direct sunlight
• Remove plasc bag from lamp before use
• Recommended ambient temperature: under 77 °F
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY
• Do not use outdoors or near water
• Do not handle plug or appliance with wet hands
• Do not stare directly at the LEDs
DO NOT USE AN EXTERNAL DIMMER WITH THIS LAMP.
DOING SO MAY CAUSE DAMAGE TO THE PRODUCT.
UCX-_ _
So white to daylight white
2,700 K - 5,000 K
ver. 01252021
Oponal/Sold separately: Occupancy sensor / WiFi module
Plug in an occupancy sensor (sold separately) into the small socket at either end to
automacally shut off the light(s) when not in use. Ensure unit(s) are in GROUP mode.
WiFi module* (sold separately) also sold separately and available to use with the
Koncept app to control UCX Pros with your smart phone.
45
occupancy sensor*
turns o lights if no motion is detected for 15 minutes
resumes last brightness setting when motion is detected
•
•
allows user to connect with UCX Pro via a dedicated Koncept app
user can automatically sync the light color/brightness with their circadian rhythm
*sold separately
•
•
power supply cable
6To operate: