Konx PH7001 User manual

2.4GHz Digital
Wireless Video Door Phone
User Manual
●Thanks for purchasing this product.
●Please carefully read this user manual before using the product
and follow the manual to install and operate.

1
1 Introduction
The product is composed of camera, host, indoor monitor and
wireless unlock control. You can operate the indoor monitor to
communicate with visitors via voice and video, and then unlock the
door if you wish.
The product is easy to install in variable types of doors (the door
thickness ranges from 35 to 110mm, the peephole diameter ranges
from 14 to 38mm). Indoor monitor is portable. It can be hung on the
wall or cabinet, or be placed on the desk, tea table.
2 Features
(1) 2.4GHz digital frequency hopping and encryption technology,
transmission distance up to 400 meters at open area
(2) IR CUT to switch night vision
(3) Peephole is made of zinc alloy.
(4) Surveillance, wireless unlock, hands-free call and talk
(5) 16 chord melodies and melody volume is adjustable
(6) Date and time shown on the screen
(7) Indoor monitor could take pictures automatically or manually, it
could store about 100 pictures with date and time
(8) Brightness and talk volume are adjustable
(9) When the visitor comes close to the peephole within 1.5 meters,
the indoor monitor will start to work and take one photo.
(10) Peephole and Monitor with same 3200mAH Li-on battery.
(11) Peephole can work about 2 months or connect power adapter.
(12) Monitor size: 236×130×18 mm
Peephole camera size: 102×70×14mm
Peephole dia: 138mm
(13) Peephole camera view angle: 150

2
3 Packing list
4 Peephole Camera

3
5 Monitor
6 Installation instructions of peephole
Remark: Please make sure that the power switch is off or the battery
is not inserted before installation. Flexible PCB is easily twisted and
flectional, you should gently lift to avoid drape, nick, crunch caused
by bump with other hard thing.

4

5
Then user has to do three basic function tests for peephole.
(1) Turn power switch to “ON”, the peephole will make a sound of
“DU…DU…”.
(2) Turn on the indoor monitor, the display will show image clearly.
(3) Press the ‘call’ button of peephole, indoor monitor will make a
ring. After press ‘talk’ button, Indoor monitor will be able to talk with
peephole.
If all three tests are passed, the peephole installation is successful.
If not pass, the connection between flexible PCB and peephole
board may be wrong or flexible PCB may be broken down.
7. Operation
A Setting
(1) Date and time
When indoor monitor is in non-talk mode, press button for 3
seconds, there will be a "T" (for time) character on the left side of the
battery symbols on the screen. Users can set the date
(year/month/day) and the current time (hour/min). Time format is 24

6
hours. Only one peephole with one indoor monitor is available for
date setting. Press , button to select, press ▲, ▼ button to
adjust the date and time in grey.
(2) Melody and volume
When indoor monitor is in non-talk mode, press button to select
one of the 16 chord melodies as the sound. Press choose to the
volume of melody (adjust level: 1-2).
(3) Talk volume
In the talk mode, press , to adjust the talk volume, adjust level:
0-7
(4) Brightness
In the talk mode, when indoor monitor has dynamic image from
peephole, press ▲, ▼to adjust brightness. Adjust level: 0-7
B Operation
Maximum com-sign is level 6. Maximum battery bar is level 4.

7
(1) Talk, unlock
Visitor presses “call” button of the peephole.Indoor monitor will
sound melody.
A. Press button of indoor monitor to speak to visitor.
When in talking mode, press button to unlock, the unlock
signal shows on the screen.
Press button to turn off screen and enter standby mode.
B. If you do not want to let the visitor go in, no operation or press
the button to turn off the screen and then enter into standby
mode.
Indoor monitor enters into the standby mode after 30 seconds if no
any operation.
(2) Monitor
If there is no calling from the peephole, User can press the
button once to wake up the indoor monitor. Press button again
to enter monitoring and monitor the outdoor as long as you like,
monitor signal will display on the screen. Press button again to

8
quit and turn off the screen.
(3) Charge
For the first time, the battery should be charged for 3 hours every
time, Charging led is in red when charging, it turns green when the
battery is filled. The color of the battery bar will change from green to
red when the battery is in low power.
(4) Motion Detection On and Off
Press “Call” button of the camera of peephole for more than 6
seconds, the motion sensor work mode will be switched between on
and off. If Infrared light firstly flash and then turn on, the motion
sensor will start to work. If the Infrared light firstly flash and then turn
off, the motion sensor will stop working.
When power off and then power on, the default work mode will be
motion sensor off.
C Picture
(1) Take photos
When there is video from peephole, press button to take a
picture, one press captures one picture.
When the call button of peephole is pressed, if the user isn't in or no
any operation, all indoor monitors automatically save the image from
the outdoor after 10 seconds.
When take a new picture, it will replace the first picture if no is
available.
When the visitor come close to the peephole camera within 1 meters,
the indoor monitor will start to work and take one photo.
(2) Browse photos
In the non-talk mode, press , button to browse the stored
pictures, then press button or after 10 seconds to quit browse
mode.

9
(3) Delete all photos
Firstly turn off the indoor monitor, then press and button
together, turn on the indoor monitor, press and button
until the screen displays text: ’Delete all photo, please wait’ ‘no
photo , Please Power off’. After that all pictures have been deleted.
D Pair
1 Pair peephole with indoor monitor
Press ‘pair’ button of peephole, indicating light flash, press and
button of indoor monitor at the same time, the screen will show
“ver. 1v1 paring’. If pairing succeeds, the video from peephole will be
shown in the screen of indoor monitor.
2 Pair unlock control with door phone system
Unlock control is connected to 12V power adapter. Peephole uses
the battery, or is connected to the power adapter. Firstly press the
pair button of unlock control, the pair light will flash once. Press the
button of the indoor monitor under talk mode, pair light will
continuously flash.
Once again press the pair button of unlock control, pair light stops
flashing.
Finally press the button of the indoor monitor under talk mode,
the pair light will flash 3 seconds, it means that pairing is successful.
3 Pair remote control with unlock control
Unlock control is connected to 12V power adapter. Firstly press the
pair button of unlock control, pair light will flash once. Press the
button of remote control, pair light will continuously flash.
Once again press the pair button of unlock control, pair light will stop
flashing.
Finally press the button of remote control, the pair light will flash
3 seconds, it means that pairing is successful.