Korenix JetBox 5300 w User manual

JetBox 5300-w QIG v0.8
PackingList
•JetBox5300‐w
•Serialcable(RJ45toDB9male,150cm)x1
•Attached4‐pinpowerterminalblock
•Attached10‐pinDIOterminalblock
•AttachedblankettocoverSDcardslot
•Quickinstallationguide
•DocumentationandsoftwareCD‐ROM
Overview
Dimension:66(D)x149(H)x120.5(W)mm
Netweight:800g
OperatingTemp:
‐40~80℃,5to95%RH
1
JetBox5300‐wQuickInstallationGuide

JetBox 5300-w QIG v0.8
DINrailMount:
ThealuminumDINrailattachmentonthebackof
JetBox5300‐wisusedtosnapintotheDINrailplate.
Interfaces:
2x10/100Based‐Tx
2xUSB2.0(Host)
2xRS232/422/485and2xRS232
4xDIand4xDO
LEDperunit:
PowerOn/offx2(Greenon/off)
SDcardx1(Greenplug/unplug)
LEDperport:
Link/Activityx2(Greenon/Greenblinking)
FullDuplex/Collisionx2(Orangeon/Orangeblinking)
PowerSupply:DCinput:12~48Vdualinputswithreverse
protectionandredundancy
Powerconsumption:6.5W
Notice:Improperpowerinputwilldamagethedevice.
HardwareInterface
Powerswitch
On/Off
2
JetBox5300‐wQuickInstallationGuide
PowerConnector:
ConnecttheDCpowerlinetotheDC
terminalblockatthebottomofJetBox
5300‐wandturnonthepowerswitch.If
thepowerisproperlysupplied,the
powerLED(P1orP2orboth)onthe
frontpanelwillshowasolidgreencolor.

JetBox 5300-w QIG v0.8
DIO
FourDigitalinputs:Low(0V),High(2~5V)
DImaxinputcurrent=5uA
FourDigitaloutputs:Low(0V),High(2.5~3.3V)
Max.24mA@3V
★Notice: OvervoltagecurrentfordigitalinputwilldamageJetBox.
Grounding
Connectinggroundingscrewtotheearthgroundwillhelptoreduce
theinterferenceofnoise.
COMportwithRJ45connector
COM1:FullRS232
COM2:HalfRS232
COM3:HalfRS232/422/485
COM4:HalfRS232/422/485
3
JetBox5300‐wQuickInstallationGuide
LongRangeTerminationSwitch

JetBox 5300-w QIG v0.8
SoftwareSpecifications(Linux2.6.21)
TheentireJetBox5300‐wsystemcanbecontrolledbySNMP
DeviceDrivers: SDCard,USB,WatchdogTimer,UART,Ethernet
LinuxToolChain:Gcc,uClibc
Serialservicemodes:TCPserver
ManagementInterface
OnastandardPCHostwithWindowsOperationsystem,followthe
stepstologinintoLinuxinterfaceofJetBox5300‐w
GotoStart|Run,typein“cmd”andthenpressEnter.
¾TelnetJetBox5300‐iwIPaddress(thedefaultIPaddressofLAN
portis192.168.10.1)
★Note:thePCandJetBox5300‐wneedtobeinthesamenetwork
IParea.
¾Entertheusernameandpasswordforlogin.Thedefaultusername
isroot andnopassword.
Systemupgrade
ThesystemcanbeupdatedthroughTFTPserver.Ittakesafew
minutesdependingonthefilesize.
4
JetBox5300‐wQuickInstallationGuide
Copyright@2010KorenixTechnologyCo.,Ltd.
Allrightsreserved.Reproductionwithoutpermissionisprohibited.
Specificationsubjectstochangewithoutnotice.
CustomerService:[email protected]