Korenix JetNet 2205 User manual

Mount the unit
Din-Rail mount: Mount the Din-rail clip on the rear of
JetNet 2205(f) on the DIN rail.
Grounding JetNet 2205(f)
There is one grounding screw on the bottom side of
JetNet 2205(f). Connect the earth ground screw of
JetNet 2205(f) to the grounding surface to ensure
safety and prevent noise.
JetNet 2205(f)
Quick Installation Guide v1.0
Overview
JetNet 2205(f) is a compact size 5(4)-port 10/100T(X) and
0(1) port 100Base F(X) Industrial Ethernet Unmanaged
Switch, which ensures high switching performance and
easy installation. Along with its high switching performance,
it supports multiple internal performance features, such as
QoS, Flow Control, it ensures quality traffic transmission.
The JetNet 2205(f) adopts rugged metal case design to
operate in harsh environment (-40~75°C ).
It is recommended to be powered by DC 24V with 12-40V
ranged.
Installation
Connection the Fiber Port (JetNet2205f): Connect the fiber
port on your JetNet2205fto another Fiber Ethernet device,
by following the figure below. Wrong connection
will cause the fiber port not working properly.
Package Check List
JetNet 2205(f) Ethernet switch
Quick Installation Guide
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with
high industrial standard. Korenix warrants that the Product(s) shall be
free from defects in materials and workmanship for a period of five (5)
years from the date of delivery provided that the Product was properly
installed and used.
This is warranty is voided if defects, malfunctions or failures of the
warranted Product are caused by damage resulting from force measure
(such as floods, fire, etc.), other external forces such as power
disturbances, over spec power input, or incorrect cabling; or the
warranted product is misused, abused, or operated, altered and repaired
in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT
plug in power connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU
of the European Parliament and of the Council of 27 January 2003 on the
restriction of the use of certain hazardous substances in electrical and
electronics equipment (RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our
professional staff are ready to solve your problems at any time Korenix
global service center's e-mail is [e-mail].
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Support
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V-
contact on the terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires
loosened.
Note:
The recommended working voltage is DC 24V. (Input range:
DC12~40 V)
LED Color Function
PWR Green Power on
1-5(4) Green Link for 100M
Flashes Green Activity for 100M
Amber Link for 10M
Flashes Amber Activity for 10M
FX
(JetNet2205f)
Green Link
Flashes Green Activity
Connecting to Network
Connecting the Ethernet Port: Connect one end of an
Ethernet cable into the UTP port of JetNet 2205(f),
while the other end is connected to the attached
networking device. UTP port support auto MDI/MDIX
function.
The LNK / ACT LED will turn Yellow for 10M Ethernet or
Green for 100M Ethernet.

连接到网络
1. 连接以太网端口：将以太网电缆的一端连接到JetNet
2205(f) 的UTP端口，另一端连接到所连接的网络设备。
UTP端口支持自动MDI/ MDIX功能。 LNK / ACT LED将亮
起并闪烁，表示RJ-45端口链路和从RJ-45接收和发送的数
据包。
注意:
推荐的输入电压为DC 24V。(可输入范围：DC12〜40V)
概述
JetNet 2205(f) 是具有5(4)个百兆以太网络电口及1个百兆F(X)界
面工业以太网交换机。
JetNet 2205(f) 交换机采用坚固的铝合金外壳结构设计, 能够在
恶劣的工业环境(-40~75˚C) 穏定工作, 符合IP30工业防护标准。
.JetNet 2205(f) 在机身底部装有可拆缷电源线槽, 其输入电源范
围是12~40VDC, 建议采用穏定的24Ｖ直流电为设备供电
打開包裝，檢查下列配件
•JetNet 2205(f)工业媒体转换器*1
•快速安装指南*1
常规
警告:此符号表示您必须遵守的警告
注意:此符号表示您必须注意的重要注意事项。
安装
Din-Rail支架：
将JetNet 2205(F) 背面的Din-rail夹子安装在DIN导轨。
JetNet 2205(f) 接地:
JetNet 2205(f) 底部有一个接地螺丝。 将JetNet2205(f) 连接框
架接地以保证安全，防止噪音造成通信干扰。 Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
Tel:[phone]
Fax:[phone]
Business service:[e-mail]
Customer service:
[e-mail]
www.korenix.com
CPQ000N2205000
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Granted Invention: I 459757
Utility Model: M 339841
Utility Model: M 339840
客户服务
5年质保
所有科洛理思产品的设计、制造及测试都是采用较高的工业
标准。科洛理思保证自产品出货日起提供最高5 年之免费保
修服务，保修期间如因零件损坏或制程不良而导致产品故障，
我们提供免费维修服务。自然外力 （火、水、雷灾）所造成
的产品故障，或其它外部因素如电源干扰、不当电源输入、
不当接线等造成的损坏，不列入产品保固范围；此外，产品
被误用、未经授权的修理及修改等行为将造成保固条款失效。
注意! 请勿于电源开启时插拔接线端子，避免产生火花造
成系统损坏。
此产品保证完全符合欧盟2003年1月27日电气和电子设备
危害物质限制委员会限用指令2002/95/EC (RoHS)及
2011/65/EU(RoHS 2.0)。
Korenix售后服务
KoreCARE 是科洛理思科技全球服务中心，我们专业的技
术人员随时准备解答您的疑问。
科洛理思全球服务中心 EMAIL: [email protected]om
业务服务: [email protected]
官网: www.korenix.com.cn
LED Color Function
PWR 綠色 電源輸入
1-5(4) 綠色 RJ-45端口链路 100M
閃綠 RJ-45接收和发送100M数据包
棕色 RJ-45端口链路 10M
閃棕 RJ-45接收和发送10M数据包
光口 綠色 光口链路
閃綠 光口接收和发送的数据包
输入电源接线:
1.将正极和负极线插入端子块连接器上的V +和V-触点。(如右上
图)
2.拧紧电线夹螺钉，防止电源线松动。
光口连接 (JetNet 2205(f)
1. 光口连接:光纤线一端连接JetNet光口，另一端连设备，如
下图所示连接模式。错误的连接会致使光口不能正常工作