kozy heat 932 User manual

INSTALLATION
AND
OPERATING MANUAL
March 2009 - R20
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
WARNING: This product must be
installed by a licensed plumber or
gas fitter when installed in the
Commonwealth of Massachusetts.
IMPORTANT: Installation of a CO detector is
required in the fireplace room when installed
in the Commonwealth of Massachusetts.
GAS FIREPLACE
◙ Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
IF YOU SMELL GAS:
◙ Do not light any appliance.
◙ Do not touch any electrical switch: do not use any phone in your building.
◙ Immediately call gas supplier from a neighbors phone. Follow the gas supplier instructions.
◙ If you cannot reach your gas supplier, call the fire department.
◙ Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
WARNING: If the information in these instructions are not followed exactly, a fire or
explosion may result, causing property damage, personal injury or loss of life.
This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type (s) of gas indicated on
the rating plate. A conversion kit is supplied with the appliance.
www.kozyheat.com
#216-F-21-4

INTRODUCTION
Read this manual before installing or operating this appliance.
Please retain this owner‟s manual for future reference.
CONGRATULATIONS!
We welcome you as a new owner of a Kozy Heat gas fireplace. Kozy Heat
products are designed with superior components and materials and assembled by
trained craftsmen who take pride in their work. The burner and valve assembly are
100% test-fired and the complete fireplace is thoroughly inspected before packaging
to ensure that you receive a quality product. Our commitment to quality and
customer satisfaction have remained the same for over 30 years. We offer a
complete line of gas and wood fireplaces, unique cabinets and stylish accessories to
compliment any décor. Adding a fireplace is one of the best ways to increase the
value of your home and we are proud to offer a network of dealers throughout the
country to help make your experience everything you imagine. We pride ourselves in
being dedicated to not only function and reliability, but customer safety as well.
We offer our continual support and guidance to help you achieve the maximum
benefit and enjoyment from your Kozy Heat gas fireplace.
Jim Hussong Dudley Hussong
President Board Chairman
Homeowner Reference Information
We recommend that you record the following information about your fireplace.
Model Name:______________________________ Date purchased/installed:____________
Serial Number:____________________________ Location of fireplace:_______________
Dealership purchased from:__________________ Dealer Phone:_____________________
Notes:_____________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
Page 1

INDEX
SAFETY REQUIREMENTS / SPECIFICATIONS………………………………………………………………… Cover / 3
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS…………………………..…………………………. 4
APPROVED VENT SYSTEMS ……………..…………………………………………………………………………….. 5
CLEARANCE REQUIREMENTS ……………………..………………………………………………………………….. 5
GAS CONVERSION INFO ……………………………..…………………………………………………………………. 5
INSTALLATION LOCATION OPTIONS …………………..…………………………………………………………….. 7
PREPARING FIREPLACE FOR INSTALLATION ……………………..………………………………………………. 6
ROUGH-IN CHIMNEY OPENING ……………………………. 8
ROUGH-IN WALL ENCLOSURE …………………………….. 8
VENTING REQUIREMENTS …………………………………………………………..………………………………… 9-12
TERMINATION VENT CAP LOCATION …………………………………..……………………………………………. 11
FLEXIBLE VENT SYSTEM INSTALLATION ……………………………..……………………………………………. 13
FAN INSTALLATION ………………………………………………………..……………………………………………. 14-15
GAS LINE REQUIREMENTS & INSTALLATION …………………………..…………………………………………. 16-17
MILLIVOLT BOARD REMOVAL ……………………………………………...………………………….………………. 17
.
MILLIVOLT BOARD INSTALLATION ……………………….. 18
LOG INSTALLATION ………………………………….…………………………………………………………………… 19
THERMOSTAT, REMOTE CONTROL, WALL SWITCH ………………………...……………………..……………… 20
COMPLETING FIREPLACE INSTALLATION ………………………………………………..……………………….. 21-22
LIGHTING & SHUTDOWN PROCEDURES ……………………………………………..……………………………. 23-25
PRESSURE TESTING ……………………………………………...…………….………………………………………. 26
MAINTENANCE REQUIREMENTS …………………………………………….…………..…………………………… 27
TROUBLESHOOTING GUIDE ………………………………………………………………………..………………… 28-29
REPLACEMENT PARTS ……………………………………………………………………………...…………………. 30
WARRANTY ………………………………………………………………………………………...…………………….. 31-32
Page 2

This appliance has been tested to and complies with ANSI Z21.88b-2008/CSA 2.33b-2008, “VENTED GAS FIRE-
PLACE HEATER”. Installation must conform with local building codes, or, in the absence of local building
codes, with the national fuel gas code, ANSI Z223.1, NFPA 54 - current edition, or the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3288.
Page 3
Installation and repair should be done only by a qualified service person. The appliance should be
inspected by a qualified service person before use. Annual inspection by a qualified service person is
required to maintain warranty. More frequent cleaning may be required due to excessive lint from
carpeting, bedding materials, etc. It is imperative that control compartments, burners and
circulation air passageways of the appliance be kept clean.
If this appliance is installed directly on carpeting, tile or other combustible material other than wood
flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth
of the appliance.
Children and adults should be alerted to the hazards of high surface temperatures and should stay
away to avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the appliance.
Clothing or other flammable material should not be place on or near the appliance.
Adequate accessibility clearances for servicing and proper operation must be maintained.
This appliance must not share or be connected to a chimney flue serving any other appliance.
Keep area around the appliance clear of combustible materials, gasoline and other flammable vapor
and liquids.
The flow of combustion and ventilation air must not be obstructed.
Due to high temperatures the appliance should be located out of traffic and away from furniture and
draperies.
The glass front or any part removed for servicing the appliance must be replaced prior to operating
the appliance. Work should be done by a qualified service technician.
Clean glass only when cool and only with non-abrasive cleansers.
Do not operate this appliance with the glass/frame assembly removed, cracked or broken. The glass
assembly, Part #700-08T, shall only be replaced as a complete unit, as supplied by Hussong Mfg. Co.,
Inc. Replacement of the glass assembly must only be performed by a licensed or qualified service per-
son. DO NOT SUBSTITUTE MATERIALS.
Do not strike or slam glass assembly.
Any safety screen or guard removed for servicing the appliance must be replaced prior to operating
the appliance.
Under no circumstances should any solid fuel (wood, coal, paper or cardboard etc.) be used in this
appliance.
Keep burner and control compartment clean.
Do not use this fireplace if any part has been under water. Immediately call a qualified service
technician to inspect this appliance and to replace any part of the control system and any gas control
which has been under water.

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS
NOTE: The following requirements reference various Massachusetts
and national codes not contained in this manual.
For all sidewall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, includ-
ing those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than (7) feet above finished grade in the area of the
venting, including but not limited to decks and porches, the following requirements shall be satisfied:
INSTALLATION OF CARBON MONOXIDE DETECTORS
At the time of installation of the side wall horizontally vented gas fueled equipment, the installing plumber or gas-fitter shall observe that a hard wired
carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the
installing plumber or gas-fitter shall observe that a battery operated or hard wired carbon monoxide detector is installed on each additional level of
the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner
to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or attic, the hard wired carbon monoxide detec-
tor with alarm and battery back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty
(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide
detector with an alarm shall be installed.
APPROVED CARBON MONOXIDE DETECTORS
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS
certified.
SIGNAGE
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum of eight (8) feet above grade directly
in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print no less the
one-half inch (1/2) in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
INSPECTION
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection,
the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08 (2) (a) 1 through 4.
EXEMPTIONS
The following equipment is exempt from 248 CMR 5.08 (2) (a) 1 through 4:The equipment listed in Chapter 10 entitled “Equipment Not Required To
Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and Product Approved side wall horizontally vented gas fueled equip-
ment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED
When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system com-
ponents with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
Detailed instructions for the installation of the venting system design or the venting system components; and
A complete parts list for the venting system design or venting system.
MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED
When the manufacturer of Product Approved side wall horizontally vented gas equipment does not provide the parts for venting the flue gases, but
identifies “special venting systems”, the following requirements shall be satisfied by the manufacturer:
The referenced “special venting systems” instructions shall be included with the appliance or equipment installation instructions and;
The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts
lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
Page 4

UNIT SPECIFICATIONS -
Height (A): 25"
Front Width (B): 32"
Back width (C): 22”
Depth (D): 18 ¼”
Face to front of 7” intake: 7 ¾”
Face to center of 4” exhaust: 11 ¼”
Flue size: 4" exhaust, 7" intake
Flex Kits (4”x7”): (pipe, cap, firestop)
- #745 Flexible TERMINATION KIT - for
terminations 4' for less.
- #718 Flexible TERMINATION KIT - for
terminations greater than 4' but less than 8'.
-#746 Flexible EXTENSION KIT - used in
conjunction with #745 or #718. The extension
kit is expandable to 6'.
IMPORTANT: THIS FIREPLACE IS APPROVED FOR USE WITH ONE OF THE FOLLOWING DIRECT VENT SYSTEMS:
Rigid Pipe (4”x6⅝”): (vertical applications only)
- #923-C adapter (Kozy Heat part) is required to
adapt the flue collar to the following systems.
● Simpson Dura Vent
● Selkirk
● AmeriVent
● Security
● EXCEL Direct
For visual inspection of proper vent connection; upon completion of installing the direct vent kit, remove the nuts and the baffle inside
the unit to expose the lower end of the flue gas exit. Re-install baffle upon inspection and secure with nuts - DO NOT OVER
TIGHTEN THE NUTS!
IMPORTANT: NON-COMBUSTIBLE FACING MATERIAL MAY BE APPLIED OVER THE FACE. TO PREVENT THE FACING MATERIAL FROM
CRACKING AND FALLING OFF DUE TO EXPANSION OF THE FACE WHEN HEATED, DO NOT ATTACH FACING MATERIAL DIRECTLY TO
THE FACE OF THE UNIT.
CLEARANCES
Minimum clearance to combustibles:
From unit sides & back: 0"
From unit top stand-off: 0"
To flooring: 0"
From flue vent: 1"
From unit glazing to adjacent sidewall: 8"
From heat outlet to mantel: See chart below -
GAS CONVERSIONS
This fireplace is manufactured for use with Natural Gas. An LP Gas conversion kit is included with this fireplace. Follow instructions
included with the conversion kit.
Natural Gas Conversion Kit - used to convert an LP millivolt board to natural gas. Part: #OCK-S38
LP Gas Conversion Kit - used to convert a Natural Gas millivolt board to LP Gas. Part: #OCK-S53 (included)
The conversion shall be carried out in accordance with the requirements of the provincial authorities having jurisdiction and in
accordance with the requirements of the ANSI Z223.1 installation code.
MANTEL PROJECTION CHART
Page 5

A) PREPARE THE FIREPLACE
1. REMOVE THE GLASS ASSEMBLY.
See Figure 2.
A. Locate the spring-loaded latch handles securing
the glass assembly (under the firebox).
B. Pull the handles out, then down to release the
glass assembly.
C. Pull the bottom of the glass assembly out and lift
up off the tabs (at the top).
D. Set aside where it will not be broken.
E. Remove the log package from the firebox and
set aside.
Figure 2
B) DETERMINE LOCATION
1. Determine the exact position of your fireplace.
If possible, place the fireplace in such a man-
ner that the venting will be placed between
two studs so additional framing is not neces-
sary. Determine the width, depth and height
of the (optional) hearth.
2. This fireplace may be installed on either the
outside or inside of an exterior wall. See Fig-
ure 3, page #7 for various installation options.
The location of doors, windows, soffits/
overhangs, etc. must be considered in relation
to where the vent termination cap will be lo-
cated. Refer to page #11
All clearances to combustible requirements
must be maintained. Follow the clearance
requirements on page #5.
3. If the optional heat ducts are used, their location
must be considered in relation to the fireplace.
The heat ducts may be vented into the same room as
the fireplace or may be vented to other rooms. A
maximum run of 20 ft. for each duct is recommended.
Venting should be completed before framing the unit
In.
Refer to instructions included in the #970 duct kit for
complete installation requirements.
4. If using the optional fan kit, 110V-120V wiring should
be run to the lower left of the fireplace by a qualified
technician. A removable electrical access panel with
romex connector is located on the left side of the fire-
place. The wiring should be run prior to enclosing the
sides of the unit.
CAUTION: COLD AIR TRANSFER AREA. THE SURROUNDING WOOD CHASE OF THE OUTSIDE WALL MUST
BE INSULATED TO PREVENT COLD AIR FROM ENTERING THE ROOM.
NOTE: Due to high temperatures, this unit should be located out of traffic areas and away from furniture and
draperies
Page 6

INSTALLATION OPTIONS
Figure 3
Page 7

5. Cut a hole for the firestop, 9 1/2" x 9 1/2".
The top of this hole must be a minimum of:
- 42 1/2" * (A)
above the height of the hearth (hearth is optional).
See Figure 4A.
*Important: This measurement is determined by
the vertical height and horizontal length of the
venting application desired. The measurement is
to the top of the pipe. Please refer to pages #6 -
#11 of this installation manual for requirements
and restrictions.
Rough in the wall enclosure -
The minimum rough opening dimensions are:
25 1/4" high (A)
32 1/2" wide (B)
18 1/2" deep
Build an optional hearth to the desired size
and height. See Figure 4B
Figure 4A
Figure 4B
NOTE: When the fireplace is installed directly on carpeting, tile, or other combustible materials other than wood flooring, it must be
installed on a metal or wood panel extending the full width and depth of the unit. The minimum for the support platform under the
unit is: 18 1/4" deep by 32" wide. If masonry is to be used (optional), prepare the necessary foundation for the masonry load. When
masonry construction is being used, a lintel must be used over the top of the unit to support the added weight.
NOTE: A non-combustible hearth extension is not required. If a hearth extension is desired, combustible materials
may be used.
NOTE: Provide for a minimum of 6" of clearance in front of the lower grill. This will provide adequate space to open the
lower grill and operate the controls.
Do not obstruct the upper and lower grill areas to allow proper ventilation air around the fireplace. Air enters the unit at
the lower grill, and exits at the upper grill. Blocking these passages may result in overheating the fireplace creating a
potentially hazardous situation.
7. Place the fireplace into position.
FIRESTOP
DESIRED HEARTH HEIGHT
A
DESIRED HEARTH HEIGHT
B
A
Page 8

VENTING REQUIREMENTS
THIS FIREPLACE IS APPROVED FOR USE WITH ONE OF THE FOLLOWING DIRECT VENT SYSTEMS:
HORIZONTAL TERMINATIONS
VERTICAL TERMINATIONS
Flex Kits (4”x7”) : (pipe, cap, firestop)
- #745 Flexible TERMINATION KIT - for terminations 4' for less.
- #718 Flexible TERMINATION KIT - for terminations greater than 4' but less than 8'.
- #746 Flexible EXTENSION KIT - used to extend the #745 or #718. The extension kit is expands to 6'.
Rigid Pipe (4”x6⅝”) : (vertical applications only)
- #923-C adapter (Kozy Heat part) is required to adapt the flue collar to the following systems.
Vertical Rise
HORITZONTAL &
VERTICAL VENTING CHART
Horizontal Run
Page 9
● Simpson Dura Vent
● Selkirk
● AmeriVent
● Security
● EXCEL Direct

RESTRICTOR INSTALLATION
The restrictor plate included in the fireplace components
packet can be installed as either a large or small restrictor,
depending on your specific vertical venting configuration.
There are several factors which can affect proper draft of the
vent system and the burner operation of a fireplace. Installing
a restrictor may be necessary to resolve the problem, even
though it may not be required under „normal conditions‟.
IMPORTANT: DO NOT INSTALL IF THE VENTING
CONFIGURATION
IS AT THE MINIMUM REQUIREMENTS!
The restrictor included is sized as the „large‟ restrictor, Figure
6A. To reduce the size to the small restrictor, simply bend the
section without the tabs off at the perforation and discard,
Figure 6B.
To install the restrictor, refer to Figures 7A & 7B and bend the tabs „up‟ far enough (approximately 80-degrees) so that
when positioned into the exhaust pipe, will create tension to hold itself in place. Do not over bend the tabs! Slide the
restrictor into the exhaust pipe with the tabs pointing toward you. Access to the exhaust pipe can be gained by remov-
ing the nuts securing the exhaust baffle inside the firebox at the top.
IMPORTANT: REPLACE THE EXHAUST BAFFLE AFTER RESTRICTOR INSTALLATION IS COMPLETE. DO NOT
OVER TIGHTEN THE NUTS!
Remove
this section
Figure 6A
Large Restrictor
Figure 6B
Small Restrictor
Figure 7A Figure 7B
Install with the tabs pointing towards you.
Page 10

TERMINATION VENT CAP LOCATION
1. Terminations against vinyl siding must use a vinyl siding protector. Follow instructions included.
2. DO NOT RECESS TERMINATION KIT INTO OUTSIDE BUILDING MATERIALS - i.e.: brick, stone, siding, etc.
If necessary, extend framing so that termination kit will be exposed once building materials are installed.
3. Vent termination must not be located where it will become plugged by snow or other material. The flow of combustion
and ventilation air must be not obstructed.
A. Above grade, veranda, porch, deck, balcony - 12"
B. Operable window or door - 12"
C. Permanently closed window* - 12" (recommended to prevent condensation on window).
D. Ventilated soffit* - 24"
E. Unventilated soffit* - 12"
F. Outside corner* - 12"
G. Inside corner* - 12”
H. Meter / Regulator: Not to be installed above a gas meter/regulator assembly within 3 ft. horizontally from
the centerline of the regulator.
I. Gas Service regulator vent outlet - 3 ft. radius
J. Non-mechanical air supply inlet to building or the combustion air inlet to any other appliance - 12"
K. Mechanical air supply inlet - 3 ft. above if within 10 ft. horizontally. Massachusetts installations: 10 ft.
L. Above paved side-walk or paved driveway located on public property - 7 ft.
LOCATION CLEARANCES
This gas appliance must not be connected to a chimney serving any other appliance.
B
B
L
DENOTES WHERE INSTALLATION NOT ALLOWED
J
K
C
G
P
H
I
O
D
E
A
N
F
M
NOTE: A vent cannot be located directly above a side-walk or paved driveway
that is located between two single family dwellings and serves both dwellings.
M. Under veranda, porch, deck, or balcony (must be fully opened on a min. of 2 sides) - 12"
N. Between two horizontal terminations - 12"
O. Between two vertical terminations - 12" Terminations may be the same height.
P. Above furnace exhaust or inlet - 12"
*Clearance must be in accordance with local installation codes & the requirements of the gas supplier.
Page 11

HORIZONTAL VENTING REQUIREMENTS
MINIMUM VERTICAL RISE* FROM TOP OF UNIT: 18 IN. (to top of 7” pipe)
MINIMUM HORIZONTAL RUN: 6 IN.
MAXIMUM HORIZONTAL RUN: 20 FT. (Horizontal runs must maintain 1/4” rise per ft.)
TOTAL HORIZONTAL & VERTICAL RUN MUST NOT EXCEED 32 FT.
*Minimum vertical rise directly off the top of the unit is determined by the length of the horizontal run. Refer to the vent-
ing diagram on page #9.
ELBOWS: For each additional elbow used after the first elbow, you must subtract 5 ft. from the maximum horizontal
run allowed.
For example: A vertical rise of 18” directly off the top of the unit with a 90oelbow would be allowed to run
6‟ with 1/4” rise per ft.. If an additional elbow is used within this vent run, the maximum horizontal run
allowed would be 1‟ with 1/4” rise per ft.. (6 ft - 5 ft. (for additional elbow) = 1 ft.)
VERTICAL VENTING REQUIREMENTS
NOTE: MINIMUM VERTICAL RISE FROM TOP OF UNIT: 18 IN. (to top of 7” pipe)
MAXIMUM VERTICAL RISE FROM TOP OF UNIT: 32 FT.
ELBOWS: 45oonly (Dura-Vent chimney systems)
MINIMUM CLEARANCE TO COMBUSTIBLES: 1"
WHEN VERTICALLY TERMINATING, THE MINIMUM CHIMNEY HEIGHT ABOVE THE ROOFLINE IS DETERMINED BY THE
FOLLOWING CHART:
Roof Pitch Minimum Chimney Height Roof Pitch Minimum Chimney Height
Flat to 6/12 1 ft. 13/12 to 16/12 6 ft.
6/12 to 9/12 2 ft. 17/12 to 21/12 8 ft
10/12 to 12/12 4 ft.
Figure 9
Page 12

1. If your chimney termination is 8' or less from the s t o v e
top and doesn‟t require an extension kit, proceed to step
#7.
2. If your chimney termination will require one or more
extension kits (part #746), proceed with the following
steps. Each #746 extension kit contains enough 4"
& 7" flexible aluminum pipe to extend the chimney
an additional 6'.
3. Gently stretch the 4" & 7" flexible aluminum pipes on
the termination kit (#745 or #718) and on each ex tension
kit, if used, the length required so when all the sections
are connected together, the vent system length for your
venting configuration is attained.
4. Using your extension kit pieces, place a bead of sealant
outside the 4" flex pipe collar (C) - the end without
the lip, and slide it inside the 4" pipe on top of the fire
place (D). Secure with 3 evenly spaced screws.
NOTE: This connection is very difficult to remove
without damaging the collars once installed.
5. Place a bead of sealant outside the 7" flex pipe collar (E)
- the end without the lip - and slide it inside the 7" pipe on
top of the fireplace (F). Secure with 3 evenly placed
screws.
6. If additional extension kits are used, repeat steps #4 and
#5, placing the 4" & 7" pipes onto the previous extension
kit.
Referring to Figure 10:
7. Apply a liberal bead of exterior sealant around the outer
edge of the termination kit box (A), and, from the outside,
place the exterior wall assembly through the 9 ½ "
square hole. Place screws through the four holes (B)
securing it in place.
NOTE: Attachment brackets are included with the termina-
tion kit. These optional brackets should be screwed, or nailed
(screws not provided) onto the top and bottom of the 9 ½ "
square hole, on the exterior of the house. The termination
plates then fit in between these brackets, and using the
screws provided, screw the brackets to the termination kit box
(A). Attach the vinyl siding protector.
7a. OPTIONAL: Place insulation between the 7" pipe and
the wall studs.
7b. The flexible termination kit includes an interior firestop
assembly (G) shown on Figure 4A, page #8, which is
installed on the inside wall (over wall materials), around the
flexible pipe. Slide the firestop over the flex pipe with the
spacer legs toward the wall.
OPTIONAL: Apply a liberal bead of sealant
around the outside / wall side edge and place
over the 9 1/2” square opening.
7c. Secure each corner with a drywall screw.
8. Gently pull the 4" & 7" flexible aluminum down to
the top of the extension kit, or the top of the unit if
no extension kits were used.
9. Place a bead of sealant outside the 4" flex pipe collar
(C) and slide it inside the 4" pipe on top of the fireplace
(D). Secure with 3 evenly spaced screws.
NOTE: This connection is very difficult to remove
without damaging the collars once installed.
10. Place a bead of sealant outside the 7" flex pipe collar
(E) and slide it inside the 7" pipe on top of the fireplace
(F). Secure with 3 evenly spaced screws.
INSTALLATION OF THE #700 SERIES FLEXIBLE HORIZONTAL DV TERMINATION KIT(S)
NOTE: #700 Series vent kits must be supported every 3 ft. to maintain proper rise. The flex pipe is permanently attached to the
exterior wall plate. Do not attach the #745 or #718 termination kit to the fireplace (or extension kit) until it has passed
through the wall. The termination plates should all be installed on the exterior of the outside wall.
Figure 10
Note: The required
18” minimum vertical
rise measurement is
to the top of the 7”
pipe
Page 13

FAN KIT INSTALLATION (OPTIONAL)
INSTALLATION OF THIS FAN SHOULD ONLY BE PERFORMED BY A QUALIFIED INSTALLER
IMPORTANT: THE FAN IS EASIEST TO INSTALL BEFORE THE MILLIVOLT BOARD IS CONNECTED TO
THE GAS LINE.
IMPORTANT: IF THE LOWER GRILL HAS BEEN INSTALLED, IT MUST BE REMOVED TO PROPERLY
INSTALL THIS FAN.
NOTE: The fan wiring must be done prior to enclosing the sides of the fireplace. An electrical box & romex
connector are pre-installed on a removable panel on the left side of the fireplace. A receptacle speed
control assembly and (3) wire nuts are included in the fireplace components packet.
The optional fan kit #932-028 includes:
1. Right and left fan assemblies with magnetic limit switch already attached.
2. Components package: (4) nuts (600-1 only), installation instructions.
NOTE: To wall-mount the speed control, you will need to purchase a speed control assembly & mounting plate, an electrical
box to mount the speed control and a cover / switch plate with screws.
IMPORTANT: Code approved line voltage wiring 14 gauge or better must be used when wiring this assembly. Refer to
your local electrical codes for specific requirements in your area.
WARNING: This appliance is equipped with a three-prong (grounding) plug for protection against shock
hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or
remove the grounding prong from this plug.
IMPORTANT: INSERT 110-120V WIRING (WITH GROUND)
THROUGH THE ROMEX CONNECTOR AND WIRE TO THE
SPEED CONTROL/RECEPTACLE ASSEMBLY MATCHING THE
BLACK, WHITE & GREEN (GROUND) WIRES TO THE CORRE-
SPONDING WIRES ON THE SPEED CONTROL/RECEPTACLE
ASSEMBLY. NOTE: 2 WIRE NUTS ARE PROVIDED IN THE
FIREPLACES‟ COMPONENTS PACKET.
See wiring diagram below.
Page 14
Incoming 110-120V
wiring

FAN KIT INSTALLATION (continued)
1. Remove the lower grill, if installed.
2. OPTIONAL: For easier installation, the fans may be separated by unplugging the three-prong plug from the receptacle in the
right fan assembly.
3. Slide the left fan (A) (without receptacle) through the lower grill opening (right side of the valve) and place over the (2) left
mounting studs (B) located towards the back of the fireplace.
3b. Slide the right fan (with receptacle) (C) through the lower grill opening (right side of the valve) and place over the (2) right side
mounting studs (D) located towards the back of the fireplace.
4. Place nuts on mounting studs and tighten.
5. If the fans were separated in step #2 above, plug fans together by inserting the three-prong male end on the short fan cord on
the left fan assembly into the receptacle in the right fan assembly.
6. Remove the (2) screws securing the removable access panel (with electrical box & romex connector installed) from the side of
the fireplace.
7. Insert 110V-120V wiring (with ground) through the romex connector and wire to the speed control / receptacle assembly
matching the black (hot), white (neutral) and green (ground) wires to the corresponding wire on the speed control / receptacle
assembly. NOTE: (3) wire nuts are included in the fireplace components packet.
8. Secure the speed control / receptacle assembly (E) into the electrical box with the (2) screws provided.
9. Replace the electrical access panel and secure with the (2) screws removed.
10. Place the temperature control switch (with magnet) on the bottom of the firebox.
11. Plug the fan cord (F) into the receptacle in the electrical box.
12. Turn on/off speed control counter-clockwise until it „clicks‟. This is the „OFF‟ position.
13. Turn the speed control „ON‟ by turning the knob clockwise past the „click‟ - this is the highest setting.
14. Replace lower grill, if removed in step #1 above.
The fan will not operate unless the speed control has been turned „ON‟. The fan will not turn „ON‟ until suffi-
cient heat is applied to the thermostatic control switch . The fan will turn „ON‟ and „OFF‟ automatically when
the fireplace heats and cools. Adjust fan to desired speed while it is running.
TEMPERATURE CONTROL SWITCH POSITION: Prior to adjusting the temperature control switch, unplug the 3
-prong plug on the fan cord from the receptacle. Adjust the position of the temperature control switch to a
warmer location under the firebox to turn the fan „ON‟ sooner or move it to a cooler location under the firebox
to turn the fan „ON‟ later. The fan will turn on when the sensor in the temperature control switch reaches 110oF
and will turn „OFF‟ when the sensors reach 90oF. After adjustment, plug the 3-prong plug on the fan cord into
the receptacle.
NOTE: This appliance must be electrically grounded and connected in accordance with local codes, or in the
absence of local codes, with the National Electrical Code, ANSI/NFPA 70-Current edition.
Figure 11
A
B
C
D
E
F
Connect fans
together here
Page 15

RUN THE GAS LINE
Caution: Installation of a gas line must only be performed by a qualified person in accor-
dance with local building codes.
GAS CONVERSIONS:
This fireplace is standard for use with Natural Gas. An LP Gas conversion kit is included with this fireplace.
Follow instructions included with this conversion kit.
LP Gas Conversion Kit: #OCK-S53 - used to convert a Natural Gas appliance to LP Gas (included standard)
Natural Gas Conversion Kit: #OCK-S38 - used to convert an LP appliance to Natural Gas.
NOTE: This fireplace is equipped with a flexible gas connector and manual shut off valve.
NOTE: The gas line should be run to the point of connection where the shut-off valve and flexible gas line will connect.
CAUTION: The manual shut-off valve or flexible gas tubing must not extend outside of the unit cavity. See the
WARNING label affixed to the flexible tubing for additional installation instructions and warnings.
NATURAL GAS: The minimum inlet gas supply pressure: 7.0 inches W.C. (recommended)
The maximum inlet gas supply pressure: 10.5 inches W.C.
Manifold pressure: 3.5 inches W.C.
Manifold pressure (lo setting): 1.7 inches W.C.
Orifice size: 38 Input: 26,000 BTU‟s Efficiency: 71.2% AFUE: 67%
LP GAS: The minimum inlet gas supply pressure: 11.0 inches W.C. (recommended)
The maximum inlet gas supply pressure: 13.0 inches W.C.
Manifold Pressure: 10.0 inches W.C.
Manifold Pressure (lo setting): 6.5 inches W.C.
Orifice size: 53 Input: 26,000 BTU'S Efficiency: 73% AFUE: 66.7%
The efficiency rating of this appliance is a product thermal efficiency rating determined under continuous
operating conditions and was determined independently of any installed system.
NOTE: For high altitude installations consult the local gas distributor or the authority having jurisdiction for proper rating
methods.
Page 16

RUN THE GAS LINE (continued)
1. Run the gas line. An accessible shut off valve must be installed up stream from the regulator.
NOTE: Do not run the incoming gas line in a manner that would obstruct the operation of the fan.
2 . This fireplace is designed to accept either a 3/8" or 1/2" gas line approved for gas appliances. Consult local
building codes to properly size the gas supply line leading to a 3/8" reduction.
3. A gas line access hole is located on either side of the fireplace for gas line connection.
4. Connect the gas line to the manual shut-off valve.
5. Connect the flexible gas line (installed on the millivolt board valve) to the manual shut off valve.
IMPORTANT!
ALL CONNECTIONS, WHETHER FIELD OR FACTORY MADE MUST BE CHECKED FOR LEAKS!
NOTE: The appliance and its individual shutoff valve must be disconnected from the gas supply piping sys-
tem during any pressure testing of that system at test pressures in excess of ½ psi.
NOTE: The appliance must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less
than ½ psi.
Pressure check taps for both the manifold (outgoing) & inlet (incoming) pressures are located in front of the
gas valve. The left pressure tap is the manifold pressure and the right pressure tap is the incoming pres-
sure. Follow instructions on page #23 for checking these pressures.
F) SECURE THE MILLIVOLT BOARD. See Figures 12A - 12D.
NOTE: The fireplace is equipped with the millivolt board & burner/cover assembly already installed. Ensure
that all of the nuts are tightened, securing the board to firebox and the burner cover is properly secured. Fol-
low these procedures in the event this assembly needs to be removed for service and/or maintenance.
1. Turn the control knob to “OFF”.
2. Remove the upper grill, glass assembly, log &
burning embers.
3. Shut off the gas supply at the manual shut-off
valve.
4. Disconnect gas line flex tube from the manual
shut-off valve.
5. Disconnect any wall switch, remote control or
thermostat wires from the valve.
6. Loosen and remove the (2) nuts securing the
burner cover, Figure 12A.
7. Remove the burner cover and set aside.
Millivolt Board Removal (if necessary)
¼” nuts securing burner cover
Figure 12A
8. Loosen and remove the (8) 1/4" nuts (the 8
along the edges only) securing the millivolt
board and, while grasping the board, gently lift
it off the (8) bolts and remove from the firebox.
Page 17

INSTALLING THE BOARD.
NOTE: This fireplace is fitted with a gasket to seal the millivolt board to the firebox. Make certain this gasket is prop-
erly placed around the opening before installing the millivolt board.
1. Place the board into the firebox, aligning the (8) 1/4" holes in the board to the (8) mounting studs on the firebox
bottom.
CAUTION: Before securing the board into place make sure that all of the wires (attached under the board)
are clear and unobstructed.
PILOT SHIELD
2. Attach the 1/4" nuts (included with the board assembly) and tighten.
3. Replace the burner cover assembly, properly seating the burner tube over the orifice. The burner cover should
be ‟inside‟ the flanges on the board. Adjust burner venturi setting. Follow instructions included in the fireplace
components packet. For Natural Gas, this setting should be 3/16". For LP, this setting should be 3/8".
IMPORTANT: Ensure that the burner tube is properly seated over the burner orifice.
Page 18

LOG INSTALLATION
INITIAL BURN PERIOD
Due to the make up of the logs/ refractory brick panels, the
curing process may take up to 4 hours of burn time. During
this period, the log & refractory will discolor but will return to
their true color once curing is complete. Do not burn this fire-
place without the glass properly in place.
***Make sure appliance owner is aware of this***
Page 19
G) #932 DV LOG INSTALLATION. See Figures 13A - 13C
This #932-500A log set includes: (1) „AD‟ log (1) „BI‟ log (1) „AJ‟ log
(1) „AG‟ log (2) „M‟ logs (1) „C‟ log
(1) „HB‟ log (1) Rock wood embers pkt.
NOTE: THE „AD‟, „AG‟, & „HB‟ LOGS HAVE ALIGNMENT HOLES INCORPORATED INTO THE BOTTOM AND SHOULD BE
PLACED ONTO THE CORRESPONDING PINS IN THE BURNER COVER. THE „BI‟ LOG IS NOTCHED AND SHOULD BE
POSITIONED ONTO THE BURNER COVER PLACING THE NOTCHED OUT SECTIONS IN THE LOG TO THE BRACKETS
IN THE CENTER OF THE BURNER COVER.
1. Place the „BI‟ log onto the center of the burner cover align-
ing the notches in the bottom of the log to the brackets in
the burner cover. Figure 13A.
2. Place the „AD‟, „AG‟, „HB‟ & „AJ‟ logs into position on the
burner cover aligning the holes in the bottom of the logs to
the corresponding pins in the burner cover. Figure 13B.
IMPORTANT: DO NOT ALLOW ANY PORTION OF THE LOGS TO
COVER THE BURNER PORTS.
3. Place rock wool embers as desired onto the base logs &
burner to enhance flame & glowing effect.
4. Position top logs „M‟ and „C‟ onto the previously positioned
logs as shown in Figure 13C.
5. Place additional rock wool ember material as desired onto
the logs to enhance glowing effect.
NOTE: You will not use all the rock wool ember material at this
time. Do not plug burner portholes or use excessively.
Figure 13A
Figure 13C
Figure 13B
BI
M M
BI
AG HB
AD
C
AJ