KRAFTtech PS160CA-3 User manual

OWNER’S MANUAL
Model Number: PS160CA-3
1/4 Sheet Palm Sander
CAUTION!
To reduce the risk of fire, electric shock and personal injury, read and understand the
owner’s manual before operating this product. Save this manual.
TM
Registration Card Inside

TABLE OF CONTENTS
SECTION PAGE
Warranty 2
Introduction 2
General safety rules for all power tools 3
Specific safety rules for palm sander 5
Technical specifications 6
Functional description 6
Assembly 7
Operation instructions 8
Maintenance 10
Accessories 10
WARRANTY
FULL 2 YEAR WARRANTY ON THIS KRAFTtechTM 1/4 SHEET PALM SANDER.
TOLL FREE NUMBER: 1-866-513-6723
If this KRAFTtechTM Power Tool is found to be defective in materials or workmanship within
2 years from the date of purchase, the manufacturer will replace the product free of charge.
Warranty replacement service is available by returning tool with the original sales receipt
showing date of purchase. Call our toll free number or visit www.krafttechpowertools.com
for more information.
This warranty does not include damages or defects caused by or resulting from abuse,
accidents, alterations or commercial use. This KRAFTtechTM product is warranted for home
domestic use only. This warranty does give you specific legal rights and you may also have
other rights which may vary from state to state.
For Repair/Replacement Parts call our toll free number.
INTRODUCTION
This Palm Sander is designed to give an exceptional finish on wood surfaces and speed
stock removal. It will also remove lacquer, varnish, and other coated finishes. It can sand
flush against all three sides of the tool and fit into tight places.
It has many features that will make your job faster, easier and more convenient. Safety, per-
formance and dependability have been given top priority in the design of this tool, as well as
making it easy to maintain and operate.
WARNING Carefully read through the entire manual before attempting to use
this tool. Be sure to pay special attention to the safety rules and all the Warnings and
Cautions throughout this manual.
WARNING Read and understand all instructions. Failure to follow all instruc-
tions listed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
KRAFTtech PS160CA-3 Page 2

KRAFTtech PS160CA-3 Page 3
120V ~ 60Hz
FIG. 1
GENERAL SAFETY RULES
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized plug
(one blade is wider than the other.) This plug will fit in a po-
larized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a quali-
fied electrician to install a polarized outlet. Do not change
the plug in any way. Double insulation eliminates the need for
the three-wire, grounded power cord and grounded power supply
system. See FIG. 1.
FOR SAFE OPERATION
Consider the work area environment. Keep your area clean and well lit. Cluttered
benches and dark areas invite accidents. Do not expose power tools to rain. Do not use
power tools in damp or wet locations. Do not use power tools where there is risk of fire or
explosion.
Guard against electric shock. Avoid contact with grounded surfaces, such as pipes, radia-
tors, ranges, and refrigerators.
Keep children away. Do not let visitors touch the tool or extension cord. All visitors should
be kept away from work area.
Store idle tools. When not in use, tools should be stored in a high or locked up place that is
dry and out of the reach of children.
Do not force the tool. It will do the job better and safer if used in a manner for which it was
intended.
Use the right tool. Do not force small tools or attachments to do the job of a heavy duty
tool. Do not use tools for purposes not intended; for example, do not use circular saws to
cut tree limbs or logs.
Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving
parts. Rubber gloves and nonskid footwear are recommended when working outdoors.
Wear a hair net to contain long hair.
Use safety glasses. Also use a face or dust mask if the cutting operation is dusty.
Connect dust extraction equipment. If devices are provided for the connection of dust
extraction and collection, take measures to ensure these are connected and properly used.
Do not abuse the cord. Never carry the tool by the cord or yank the cord to disconnect it
from the socket. Keep the cord away from heat, oil and sharp edges.
Secure your work. Use clamps or a vice to hold the work. It is safer than using your hand
and it frees both hands to operate the tool.
Do not overreach. Keep proper footing and balance at all times.

GENERAL SAFETY RULES
Maintain tool with care. Keep cutting tools sharp and clean for better and safer perfor-
mance. Follow instructions for lubrication and changing accessories. Inspect tool cord
periodically, and, if damaged, have it repaired by an authorized service facility. Inspect
extension cords periodically, and replace if damaged. Keep handles dry, clean and free from
oil and grease.
Disconnect tools. Always unplug the tool when it is not in use, before servicing, and when
changing accessories, such as blades, bits and cutters.
Remove adjusting keys and wrenches. Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before turning it on.
Avoid unintentional starting. Do not carry a plugged-in tool with a finger on the switch.
Make sure the switch is off when plugging tool in.
Use outdoor extension cords. When tool is used outdoors, use only extension cords
intended for outdoor use.
Stay alert. Watch what you are doing. Use common sense. Do not operate the tool when
you are tired.
Replace damaged cords immediately. Use of damaged cords can cause shock, burns or
electrocution.
Check damaged parts. Before further use of the tool, a guard or any other part of the tool
that is damaged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment of moving parts, free running of moving
parts, breakage of parts, mounting and any other conditions that may affect its operation. A
guard or other part that is damaged should be properly repaired or replaced by an autho-
rized service center unless otherwise indicated in this instruction manual. Have defective
switches replaced by an authorized service facility. Do not use the tool if the switch does
not turn it on and off.
WARNING The use of any accessory or attachment, other than those recom-
mended in this instruction manual, may present a risk of personal injury.
Have your tool repaired by a qualified person. This electric tool has been designed in ac-
cordance with the relevant safety standards. Repairs should only be carried out by a quali-
fied person using original replacement parts. Failure to do so not only will void the warranty,
but could result in injury to the user or other participants in the work area.
KRAFTtech PS160CA-3 Page 4

SPECIFIC SAFETY RULES
Always wear safety goggles and a dust mask when sanding, especially when sanding
overhead.
A suitable breathing respirator must be worn while sanding chemically pressuretreated
surfaces.
This KRAFTtech sander is not suitable for wet sanding. Using this tool for this purpose
could cause electric shock.
Do not use sandpaper that is larger than needed. Extra paper that extends beyond the
sanding pad can cause serious lacerations.
This KRAFTtech sander is equipped with a dust extraction port. Dust from the sanding
operation can be removed by attaching either a shop vacuum hose or the dust collection
bag included with the tool. When using the collection bag, be sure to empty it frequently.
Never discard sanding dust in the area of or on an open flame, as these fine wood particles
can be highly combustible.
Use of damaged cords can shock,burn, or electrocute.
TECHNICAL SPECIFICATIONS
Model PS160CA-3
Rated Voltage 120V~ 60Hz
Rated Power Input 1.5A
No Load Speed, n013,000/min
Sandpaper 1/4 sheet
V: Volts A:Amperes
~: Alternating Current Hz: Hertz
KRAFTtech PS160CA-3 Page 5

FUNCTIONAL DESCRIPTION
1. Rocker “On/Off” Switch with Dust Guard
2. Sandpaper Clamp
3. Clamp Lever
4. Pad
5. Vents
6. Cord
7. Dust Collection Bag
8. Sandpaper Punch
ASSEMBLY
WARNING Always disconnect the plug from the power source before attach-
ing or removing sandpaper. The sandpaper must be drawn as tight as possible
across the pad of the sander for efficient sanding, as a loose sandpaper can slip
on the work surface.
ATTACHING SANDPAPER
1. To open clamp, push down clamp lever as shown in (FIG. 3).
2. Place the sandpaper (grit side up) between the clamp and base plate while aligning
edges of the sandpaper with either edge of the pad. (Pre-bending the sandpaper
makes attachment easier.)
KRAFTtech PS160CA-3 Page 6
FIG. 2
1
6
7
4
3
2
5
8

ASSEMBLY
3. After inserting the sandpaper, release pressure on clamp lever making sure that the
clamp is gripping the sandpaper and the sandpaper is aligned with the pad.
4. Wrap the sandpaper around the bottom of the pad, and attach the free end of
sandpaper under the opposite clamp, repeating procedures 1, 2 & 3, above.
KRAFTtech PS160CA-3 Page 7
FIG. 3
CLAMP LEVER
PAD
SANDPAPER

ASSEMBLY
ATTACHING THE DUST BAG
Align the groove in the dust bag assembly with the groove in the vacuum port (see FIG. 4),
and then press down on the dust bag assembly to lock it in place.
OPERATION INSTRUCTIONS
SANDPAPER
This 1/4 sheet sander is designed to be used with standard, commercially available sandpa-
per sheets. Cut the sheet crosswise into quarters for a precise fit.
Aluminum oxide, silicon carbide, or other synthetic abrasives are recommended for power
sanding use. For rough sanding, sandpaper with a coarse grit is best. For smoothing or final
sanding, sandpaper with a fine or extra-fine grit should be used.
TM
FIG. 4
KRAFTtech PS160CA-3 Page 8

OPERATION INSTRUCTIONS
SANDPAPER PUNCH
To remove dust effectively from the work surface, the 1/4 sheet of sandpaper must have
holes punched through the surface. A sandpaper punch is included with your
sander. After attaching the sandpaper to the palm sander, align the sandpaper with the
punch, and push down on the sandpaper until the punch has pierced the sandpaper. The
sandpaper is now ready to use with the dust collection system on your sander. See FIG. 5.
ROCKER “ON/OFF” SWITCH
To turn the tool “ON” or “OFF”, push in the switch rocker to the left or right side of the tool.
Be sure sander is “ON” and at full speed before beginning sanding operation. Remove the
tool from the work surface before turning “OFF”.
SANDING
Do not place excessive pressure on the sander. Excessive pressure on the sander may
result in an uneven sanding job and can also cause overheating and possible damage to the
motor.
Do not leave the tool sanding in one spot for an extended time, otherwise uneven sanding
will result.
TM
FIG. 5
KRAFTtech PS160CA-3 Page 9

MAINTENANCE
WARNING A repair or replacement of this tool must be performed by a quali-
fied service technician. For information call our toll free number at 1-866-513-6723.
WARNING Always use only a soft, dry cloth to clean your sander, never use
any detergent or alcohol.
Disconnect the plug from the power source before cleaning.
CAUTION No chemical agents are approved for use in cleaning this power tool.
Clean with a dry cloth or towel only.
ACCESSORIES
Sandpaper …………………………………………………………………….....6pcs
Dust Bag ……………………………………………………………………….....1pc
Sandpaper Punch ………………………………………………………………....1pc
WARNING Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
-Lead from lead-based paints
-Crystaline silica from bricks and cement and other masonry products
-Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as those dust masks that are spe-
cially designed to filter out microscopic particles.
KRAFTtech PS160CA-3 Page 10