Kranzle 2+2 User manual

Power sweeper 2+2
Read and conform safety instructions before use!
- GB -
Operating manual

2
Description
DearCustomer
Congratulationsonyournewsweeper!
Foryourconvenience,adescriptionofthemachineisprovidedonthefollowing
pages.
Technicalspecications
Methodofoperation: 2-rollerhaspprinciple
Workingwidth: 800mm
Weight: 17kg
Containercapacity: 40litres
Brushes: heavydutypolypropylene
Seepingrate: approx.3000m²/hr

Themachineisfullyrecyclable.Itismadecompletelyofpolypropylene„PP“and
naturalrubber.Thebrushrollersaremadeofwood.
ThemachineisPVC-FREEandonehundredpercent.........
...madeby
Thesweeperisdesignedforuseonalevelsurface.
Withthesidebrushespressed,youcanpushthemachineeasilyoverthesurface
tobecleanend.Thisshouldbedonedoneatnormalwalkingspeed(approx3km/
hr).Theseepingratedependsonthespeedthebrushrollersrotate,andthisin
turndependsonthespeedthemachineispushed.Thepushingforcerequiredis
between3and3,5kg,dependingonthesurface,
Ifyouwishtomovethemachineforlongerdistanceswithoutsweeping,pullit
bachwardssothatthesweepingfunctionisdisabledbythebuilt-infree-wheel
feature.
R

3
Assembly for side brushes and push handle
Pullthepushhandleupwards
Gripthecollectorhandle...
..andliftitout
Pullthecoveroftheinterior.
...andplacetheaccessoriesontheground
Placethemachineontheground

4
Assembly of side brushes and push handle
Nowpressthesafetycapsfromabove,makingsure
thattheyareattachedtothecorrectsides(engraved
rightandleft).
Loosenthefourplasticscrews(4)onthe
undersideofthedustspoiler(3)andplace
thescrewswiththeplainwasher(5)onthe
ground.
Pressthespoilerfromthetopontothe
housing.Nowturnthescrewswiththeplain
washerfrombelowthroughtheholesinthe
housingintothespoiler.Nowtightenthe
screws.
Fixthepushbarintotheworkpositionin
hole(A)usingthestarscrewsprovided(a).
Firstplacewasherno.72onsidebrushno.74abovetheballbearingand
placebothonbearingboltA.Tightenthescrewwithsafetywashersno.76
andno.77intothebolt.
Foldbackthehandleonthemachine.Nowputthe
sweeperupsidedownonthegroundand,remove
thescrewfromthebrassaxleoftheinletbrush.

5
Description
Toreleasetheconstantpressurefromthesidebrushes,itisrecommendedafter
eachusetomovethemachineapprox.5cmbackwards,inordertorelievethe
bristlesandtoraisethesidebrushesusingthelever(c)(g.2).Thispreventsthe
bristlesfromdeforminganddiminishingtheircleaningefciency.
Toreleasestrainonthebristlesofthesweepingrollersandtosavespacein
storage,youcanunscrewthestarscrews(a)ontheleftandrightofthepushbar,
foldthebarforwardsintotheparkingpositionandreplacethescrewinholeB.
Themachinecannowbestoredverticallyandrequireslessspace.Thecontainer
doesnotneedtobeemptiedtodothis.
Storage
Toemptythecontainer
Whenthedirtcontainerisfull,takeholdofthehandleandsimplypullitupwards.
Thecontentscanthenbedisposedofaccordingly.Replacethecontainerinthe
reverseorder.
UnloadingthebrushesLoadingbrushes
Pressthetwo
brushheadstoput
theinletbrushes
intothework
position.
Theheightofthe
sidebrushescan
beadjustedon
bothsides.
Whentheinlet
brushesareno
longerrequired,
presstherelease
leverbrieyandthe
brusheswillengage
intherestposition.
Fig.1 Fig.2

6
Noworkneedtobedoneonthemachine
becauseitdoesnotrequireservicing.Ho-
wever, you should check after each use
thattherearenothreads,wireorstripsof
materialroundtheroller. If there are any,
theyshouldberemovedimmediatelysinceit
willotherwisebeimpossibleforthemachine
tooerateproperly.
Intheeventogheavysoiling,graspthedust
lters (left and right) behind the cassette
usingthescrewdriver,liftthemoutcomple-
telyandeithercleanthelterorreplaceit.
Filterpaper:
Art.-no.50.130
Repairset:
ltercassettecomplete:
Art.-no.50.190
Servicing
Warranty
Thiswarrantycoversmaterialand/orworkmanshiprelateddefectsonlyanddoesnot
extendtoordinarywear.
Machinemustbeoperatedaccordingtoenclosedoperatinginstructionswhicharepartof
presentwarrantyconditions.
Allproductssolddirectlytoprivatecustomersarewarrantiedforaperiodof24months,
whereasthewarrantyperiodforindustrialpurchasesislimitedto12months.
Incaseofanywarrantyclaims,pleasehaveyourHPcleanertogetherwithaccessoriesand
yourpurchasedocumentreadyandcontactyournearestdealerorauthorizedservicepoint
whichcanalsobelookedupintheinternetatwww.kraenzle.com.

7
Servicing
Whentherollersareworn,thesweepercan
beplacedapprox.1-1,5mmlowerbyremo-
vingthetwowashersno.13(seepage10).
Important:

Easyreplacementofbrushrollers:
1)Putthemachineuprightonthejointsof
thefolded-inpushbarandtheframe.
2)Turnthebrushrolleruntilthetwoscrews
no.34ontheleftandrightsiderespectively
arevisible(seepage12)andremovethese
4screws.
3)Turnthebrushrollersanotherhalf-turn
andremovethembypullingthemout.
4)Fitthenewrollersinthereverseorder.
One washer no. 13  must
always be kept under the
screwholetoavoiddamaging
totheplasticframe

8
Complete machine

9
Kränzle Power Sweeper 2 + 2
Pos. Description Qty. Part no.
Spare parts list Power Sweeper 2 + 2
Complete machine
Repair set:
Filter cassette, complete 50.190
 Pos.16;Pos.17;Pos.18
1 Gehäuse 1 50.102
2 Schmutzbehälter 1 50.101
3 Rechen 1 50.151
4 Abdeckungvorn 1 50.150
5 Unterlegscheibe5,3 4 50.152
6 Abweisleiste 1 50.105
7 Schraube5,0x25 2 41.4141
7.1 Kunststoffschraube5,0x20 4 43.018
8 GummilappenhintenmitKlemmleiste 1 50.171
9 Schmutzführung 1 50.163
10 Schraube3,5x9,5 28 41.088
10.1 Schraube4,8x13 4 44.112
11 Lenkrolle 1 50.164
12 SechskantschraubeM10x45 1 50.180
13 Scheibe10,5DIN9021 2 50.182
14 Scheibe10,5DIN125 1 40.138
15 Elastic-Stop-MutterM10 1 40.139
16 RahmenfürFilter 2 50.128
17 HalterahmenfürFilter 2 50.129
18 Filterpapier 2 50.130
19 Bügelunten 2 50.140
20 Schubbügel 1 50.141
21 Kunststoffschraube6,0x30 6 43.423
22 Gelenkschaleaußenlinks 1 50.142
23 Gelenkschaleaußenrechts 1 50.143
24 Gelenkschaleinnen(f.linksundrechts) 2 50.144
25 SchloßschraubeM8x30 2 50.199
26 GrifffürSchmutzbehälter 1 50.177
27 SterngriffM8 2 50.168
28 GummilappenlinksmitKlemmleiste 1 50.145
29 GummilappenrechtsmitKlemmleiste 1 50.147
85 Elastic-Stop-MutterM8 2 41.410

10
Left wheel and sweep rollers

11
Kränzle Power Sweeper 2 + 2
Spare parts list Power Sweeper 2 + 2
Left wheel and sweep rollers
Pos. Description Qty. Part no.
Repair sets:
Brush roller, front, complete 50.192
 Pos.31,2+Pos.33,4+Pos.34
Brush roller, rear, complete 50.193
 Pos.32,2+Pos.33,4+Pos.34
Cog set „left“ 50.196
 3+Pos.35,2+Pos.36,Pos.37,Pos.43,Pos.47
 Pos.48,6+Pos.49,2+Pos.53,Pos.72,
31 Bürstenwalzevorn 1 50.119
32 Bürstenwalzehinten 1 50.120
33 Bürstenmitname 2 50.121
34 Holzschraube3,5x17 4 50.165
35 Sicherungsscheibe10 6 50.133
36 Scheibe13DIN433 4 50.184
37 Zahnradz=14 1 50.115
39 Abstandshülse20,5mm 2 50.1552
40 Mitnahmebolzen(linkshinten) 1 50.126
41 Rillenkugellager12/28/8 6 50.156
42 Loslagerbolzen(linksunten) 1 50.122
43 ZahnradZ=14mitKeil(lang) 1 50.116
44 BolzenfürSeitenbesenantr.(linksoben) 1 50.124
46 Elastic-Stop-MutterM8x1 2 14.152
47 Scheibe 1 50.113
48 Zahnradlinksz=79 1 50.109
49 Mitnahme 6 50.111
50 RadmitLagerung 1 50.191
51 Achse 1 50.112
52 Radkappe 1 50.108
63 Stahlversteifung 1 50.167
72 MS-Scheibe12x24x4 1 50.149

12
Right wheel

13
Kränzle Power Sweeper 2 + 2
Spare parts list Power Sweeper 2 + 2
Right wheel
Pos. Description Qty. Part no.
Repair sets:
Cog set „right“ 50.197
 3xPos.35,3xPos.36,Pos.47,
 6xPos.49,Pos.53,Pos.56,Pos.58,
 Pos.59,Pos.61,Pos.72,
33 Bürstenmitname 2 50.121
34 Holzschraube3,5x17 4 50.165
35 Sicherungsscheibe10 6 50.133
36 Scheibe13DIN433 2 50.184
38 MS-Scheibe12x24x2,5 1 50.139
39 Abstandshülse20,5mm 2 50.1552
41 Rillenkugellager12/28/8 6 50.156
46 Elastic-Stop-MutterM8x1 2 14.152
47 Scheibe 1 50.113
49 Mitnahme 6 50.111
50 RadmitLagerung 1 50.191
51 Achse 1 50.112
52 Radkappe 1 50.108
54 Gegenlagerungzahnradgetriebe 1 50.161
56 Zahnradrechtsz=79 1 50.110
57 Loslagerbolzen(rechtshinten) 1 50.125
58 Doppelzahnrad 1 50.118
59 Aufsteckriemenscheibe 1 50.114
60
BolzenfürSeitenbesenantr.(rechtsoben)  1 50.179
61 Zahnradz=16 1 50.117
62 Mitnahmebolzen(rechtsunten) 1 50.123
63 Stahlversteifung 1 50.167
72 MS-Scheibe12x24x4 1 50.149

14
Left side brush

15
Kränzle Power Sweeper 2 + 2
Spare parts list Power Sweeper 2 + 2
Left side brush
Pos. Description Qty. Part no.
Repair sets:
Side brush drive, complete 50.194
 Pos.35,Pos.36,Pos.81,Pos.82,
Side brush, complete 50.195
 Pos.39,Pos.72,Pos.74,Pos.75
 Pos.76,Pos.77,Pos.78
7 Schraube5,0x25 5 41.4141
35 Sicherungsscheibe10 6 50.133
36 Scheibe13DIN433 6 50.184
40 Abstandshülse14,5mm 1 50.1551
41 Rillenkugellager12/28/8 2 50.156
53 MS-Scheibe12x24x2,5 3 50.139
66 Rastknopf 1 50.132
67 Fußraster 1 50.131
68 Druckfeder(klein) 1 50.158
69 Sicherungsring12DIN471 2 50.137
70 Rückstellfeder(groß) 1 50.159
71 DeckelfürSeitenbesen 1 50.134
72 MS-Scheibe12x24x4 1 50.149
74 Seitenbesen 1 50.136
75 Büchse 1 50.153
76 UnterlegscheibefürSeitenbesen 1 50.154
77 Sicherungsring8,4 1 40.054
78 SchraubeM8x16 1 50.138
79 Kunststoffabdeckunglinks 1 50.103
80 BolzenfürAntriebszahnrad 1 50.198
81 ZahnradZ=14mitKeil(kurz) 1 50.127
82 Rundriemen 1 50.160
84 Scheibe6,4DIN9021 1 50.174
85 Elastic-Stop-MutterM6 1 14.1521

16
Right side brush

17
Kränzle Power Sweeper 2 + 2
Spare parts list Power Sweeper 2 + 2
Right side brush
Pos. Description Qty. Part no.
Repair sets:
Side brush drive, complete 50.194
 Pos.35,Pos.36,Pos.81,Pos.82,
Side brush, complete 50.195
 Pos.39,Pos.72,Pos.74,Pos.75
 Pos.76,Pos.77,Pos.78
7 Schraube5,0x25 5 41.4141
35 Sicherungsscheibe10 6 50.133
36 Scheibe13DIN433 6 50.184
40 Abstandshülse14,5mm 1 50.1551
41 Rillenkugellager12/28/8 2 50.156
53 MS-Scheibe12x24x2,5 3 50.139
66 Rastknopf 1 50.132
67 Fußraster 1 50.131
68 Druckfeder(klein) 1 50.158
69 Sicherungsring12DIN471 2 50.137
70 Rückstellfeder(groß) 1 50.159
72 MS-Scheibe12x24x4 1 50.149
74 Seitenbesen 1 50.136
75 Büchse 1 50.153
76 UnterlegscheibefürSeitenbesen 1 50.154
77 Sicherungsring8,4 1 40.054
78 SchraubeM8x16 1 50.138
80 BolzenfürAntriebszahnrad 1 50.198
81 ZahnradZ=14mitKeil(kurz) 1 50.127
82 Rundriemen 1 50.160
84 Scheibe6,4 1 50.174
85 Elastic-Stop-MutterM6 1 14.1521
91 DeckelfürSeitenbesenrechts 1 50.135
92 Kunststoffabdeckungrechts 1 50.104

18
Notes

19
Notes

Reprintonlyallowedwiththeauthorizationof
Asdateof10.09.2013
R
Best.-Nr.:302201