Krell Industries LAT series Quick start guide

OWNER’S REFERENCE
LAT
THE LAT SERIES
LOSSLESS ACOUSTIC
TRANSDUCERS

The LAT Series
Lossless Acoustic Transducers
Owner’s Reference, v05.0
Krell Industries, Inc.
45 Connair Road
Orange, CT 06477-3650 USA
TEL [phone]
FAX [phone]
E-MAIL [e-mail]
WEBSITE http://www.krellonline.com
This product complies with the EMC directive (89/336/EEC) and the low-voltage directive
(73/23/EEC).
This product is manufactured in the United States of America. Krell®is a registered trademark of Krell Industries, Inc., and is restricted for use by
Krell Industries, Inc., its subsidiaries, and authorized agents. Krell HEAT™, KrellHEAT™, and LAT™ are trademarks of Krell Industries, Inc. All rights
reserved. All other trademarks and tradenames are registered to their respective companies.
© 2005 by Krell Industries, Inc. All rights reserved P/N 307595-W

1
iii
Contents
List of Illustrations, page iv
Foreword, page v
A Letter from Dan D’Agostino, page 1
SECTION ONE: About Krell, page 2
The Krell Legacy, Ensuring Maximum Performance,
and Definition of Terms
SECTION TWO: Unpacking and Placement, page 7
Opening the LAT–1000 and the LAT–C1000 Shipping Crate
Opening the LAT–2000 Shipping Box
Attaching and Detaching the Loudspeaker Grille
SECTION THREE: Anatomy of a Loudspeaker, page 14
Features and Benefits of the LAT Design
SECTION FOUR: Connecting a LAT Series Loudspeaker to Your System, page 22
SECTION FIVE: KrellHEAT: Home Theater Technology, page 23
WARRANTY, page 24
RETURN AUTHORIZATION PROCEDURE, page 26

iv
List of Illustrations
Figure 1, page 14
LAT–1000 Front Panel and Grille,
Back Panel, Tuned Port, Enclosure, Crossovers
Figure 2, page 16
LAT–2000 Front Panel and Grille,
Tuned Ports, Crossover, Back Panel
Figure 3, page 18
LAT–C1000 Front Panel and Grille, Back Panel,
Enclosure, Crossovers, Leg Assembly and Pivot Mechanism

v
Foreword
For more than 25 years, Krell components have been the choice of discerning
audiophiles all over the world. Krell customers care deeply about music, and they
demand the most lifelike music reproduction possible. Krell Industries, Inc., was
founded and exists to meet the expectations of those listeners.
Loudspeakers are an integral link in an audio system. With the right loudspeakers,
you hear music with its original definition, precision, and clarity. Krell’s lossless
technology combines the benefits of enclosure design, materials selection, and
electronics design and configuration to ensure that you hear music exactly as it
was recorded—nothing more, nothing less.
With the Lossless Acoustic Transducers (LATs), Krell has achieved its goal: loud-
speakers that are uniquely capable of delivering music with the same confidence
and accuracy as other legendary Krell components.

A Letter from Dan D’Agostino
Dear Audio Enthusiast,
Thank you for your purchase of the Lossless Acoustic Transducer.
For more than thirty years, I have been designing audio components for audio-
philes who share my passion for music and its reproduction. Krell Industries, Inc.
is a viable, dynamic company, with dealers and distributors worldwide, as a result
of my ongoing quest to build the best, most refined audio products available. This
quest has driven me towards a “systems approach”, and the development of the
Lossless Acoustic Transducer (LAT) Series of loudspeakers is an important part of
that approach. Only through the design of complete systems can I insure that
every component meets my standard of excellence.
It is a goal of mine for Krell loudspeakers to enhance your life visually as well as
sonically, and the new LAT–1000, LAT–2000, and LAT–C1000 deliver both excep-
tional performance and style. Provocative aluminum cabinetry, together with
advanced driver and crossover technologies yield loudspeakers of extraordinary
capability, providing the listener with a fresh experience of his favorite musical per-
formances. Combine these loudspeakers with my Evolution One monaural amplifi-
er and Evolution Two preamplifier, and discover a system that exceeds my expec-
tations.
I want to share an exciting new direction with you. Work on the Evolution source
under the systems approach at Krell is ongoing, as of this writing. This exceptional
player clearly demonstrates the advantages of the latest audio recording formats,
while elevating traditional compact disc performance to a new level. I urge you to
experience it, when it is released.
My passion for music reproduction and high performance is the passion that
forged Krell Industries, Inc. and sustains me to this day. It is my love of music, art,
and science that informs all my design efforts, and drives me toward great prod-
ucts such as the LAT Series of loudspeakers. Thank you for your appreciation of
my life’s work, and for choosing Krell.
Sincerely,
Daniel D’Agostino
Chief Executive Officer
1

About Krell
This section describes the Krell Legacy, Krell’s innovative loudspeaker design and
technology, and defines key terms used in this reference.
The Krell Legacy
“I design every Krell component to set the standard
for workmanship, style, and performance.”
Dan D’Agostino
High-end audio is a demanding pursuit—an ongoing quest for excellence in
music reproduction that drives equipment manufacturers to strive for the absolute
in design and performance. With a keen understanding of this passionate drive,
Krell Industries, Inc., was founded in 1980.
Over the past 2-1/2 decades, Krell has earned a distinguished reputation for engi-
neering innovation and product excellence. The company’s history is replete with
product introductions that have deeply impacted the high-end audio industry. The
most discriminating audiophiles and product reviewers have consistently recog-
nized Krell components for standard-setting performance.
The Lossless Acoustic Transducers (LATs) herald the era of loudspeaker design and
manufacture at Krell Industries, joining the legacy of amplifiers for which Krell is
renowned. For over 25 years, Krell C.E.O. Dan D’Agostino has built amplifiers
legendary for their ability to deliver optimum performance for any loudspeaker.
This experience has yielded invaluable insights about the nature of loudspeaker
design, which Krell has characteristically incorporated into the LAT Series.
The LAT Series of Loudspeakers
The LAT–1000, a reference-caliber loudspeaker, employs an all-aluminum enclosure
that remains sonically inert, with a baffle that absorbs vibrations and houses custom-
made drivers, and a robust, high-power crossover—a loudspeaker capable of
handling the legendary power of Krell amplifiers, while maintaining pinpoint
accuracy and resolution.
2
SECTION ONE

continued
3
The LAT– C1000 high performance center channel, is manufactured with all of
the crossover, enclosure, and driver technologies of the LAT–1000. Designed to be
operated as a full-range loudspeaker, the LAT– C1000 center channel loud-
speaker perfectly complements the LAT–1000. Together, these loudspeakers
form the most extraordinary home theater loudspeaker system available.
The magnetic shielding and horizontal driver array of the LAT– C1000 allows for
ease of installation above or below a video screen. In addition, multiple locator
positions in the stand assembly allow for the optimal on-axis setup of the loud-
speaker for almost all scenarios.
The LAT– 2000 is a vented two-way loudspeaker designed for a two-channel
system demanding high quality performance in a small space. This loudspeaker
is also the perfect complement to the LAT–1000 and LAT– C1000 loudspeakers
in a home theater system. Crossover, enclosure, and driver technologies used in
the LAT–1000 have been applied to the design of the LAT– 2000.
Unparalleled Sonic Performance
From the first Krell product—the KSA–100 —to the present, Dan D’Agostino has
continually “pushed the envelope” of performance in his search for greater amplifier
power, and now, loudspeaker response. His exploration of technologies, driven by
his never-ending quest to elevate the standard of excellence, has resulted in break-
through audio designs. Over the years, the Krell line of power amplifiers, including
benchmark products such as the KRS–100, KRS–200, and the Audio Standard
models, has established a legacy of unparalleled sonic performance. The LAT
Series brings the Krell level of performance to the loudspeaker.
Dan D’Agostino remains committed to the development of new designs and
technologies. And the Krell legacy will continue to evolve with products that deliver
innovative engineering, perfection in build quality, and outstanding audio performance.

(SECTION ONE: About Krell continued)
4
Ensuring Maximum Performance
The LAT-1000 extends the already impressive performance of the LAT-1 to a new
level. Building upon the foundation of solid aluminum cabinetry and high-current
crossover design that distinguished the LAT–1, the LAT–1000 frequency response
extends 1/3 octave lower than its predecessor. The LAT–1000, LAT–2000 and
LAT– C1000 have improved midrange resolution, and enhanced high frequency
detail. All designs employ new drivers that feature greater range, better power
handling, and very low distortion.
Innovative Loudspeaker Technology and Design
Crossover
The LAT–1000 and LAT–C1000 crossovers feature robust construction that
divides the circuit among three discrete circuit cards—one each for the woofer,
midrange, and tweeter networks. The LAT– 2000 loudspeaker has a two-way
crossover design, with the woofer and tweeter together on a single circuit board.
Each printed circuit board for a LAT loudspeaker is fashioned of 1/8-inch fiberglass
with 4-ounce copper traces for superior current flow. Air core inductors and
banks of potted WIMA capacitors ensure tight tolerances and high linearity during
high power levels.
Enclosure
Continuing in the tradition of the Master Reference Subwoofer, a LAT Series
loudspeaker enclosure is constructed entirely of aluminum. “Aluminum is the best
material for the job,” C.E.O. Dan D’Agostino explains. “Other than concrete and
lead, which are not practical choices, aluminum is the only material that possesses
the ideal combination of structural rigidity and resonance damping characteristics.
Within the audio passband, our cabinets are sonically inert—something you cannot
say about any wood or wood derivative.”
Krell’s knowledge of aluminum extrusion technology has yielded an enclosure that is
as purposeful as it is beautiful. Computer-optimized geometry eliminates standing
wave interference. A rear-firing, tuned port on the LAT–1000 is precision machined.
A substantive aluminum baffle, rear plates, bottom, and top comprise an enclo-
sure that is immune to vibration. Articulating spikes allow the LAT–1000 to be pre-

continued
5
cisely leveled for the most accurate imaging and reduced vibration. A special sub-
enclosure in the LAT–1000 and LAT–C1000 houses the drivers for the midrange
and the tweeter. This computer-modeled, welded aluminum case effectively iso-
lates the midrange and tweeter from the main enclosure while providing an ideal
operating environment for the midrange drivers.
The LAT–C1000 enclosure is fashioned out of solid aluminum billet and extru-
sion, creating an operating environment for the drivers that is free of induced vibra-
tions. The loudspeaker has a special advantage in the crucial midrange frequen-
cies: it is optimized for dialogue, the single most important job of a center chan-
nel speaker. The LAT–C1000 maintains the voice matching necessary to recreate
seamless multi-channel front staging. Heard through the LAT–C1000, dialogue is
natural sounding and clearly distinguishable from the rest of the audio program.
The LAT– 2000 construction is based on the same engineering principles that distin-
guish the LAT–1000. The all-aluminum enclosure features wall thickness ranging
from 0.75 to 1.0 inch. The curvature of the cabinets is designed to absolutely mini-
mize the effects of internal standing waves and external high-frequency diffraction.
The vented cabinet of the LAT–2000 features two rear bass ports. The LAT–2000
ports are precisely dimensioned, flared, and positioned with respect to the woofer
to eliminate turbulence while providing the correct acoustical loading.
Drivers
The LAT–1000 and LAT–C1000 tweeters are a 1’” ring radiator design with a
machined aluminum faceplate and phase plug. The 5.25” midrange drivers fea-
ture magnesium cones coupled to a rubber surround, and an injection molded
metal basket that is extremely rigid as well as acoustically transparent. The 8”
woofers are designed with low loss linear suspension and aluminum cones, and
a unique spider configuration dampens driver-born resonances. All drivers have
very high power handling characteristics.
The LAT–2000 tweeter is identical to the LAT–1000 tweeter. The 7” mid-bass driv-
er features a sliced paper cone and, like the LAT–1000 woofer, has an injection
molded metal basket that is extremely rigid as well as acoustically transparent. A
large motor promotes ample bass extension and midrange accuracy.

(SECTION ONE: About Krell continued)
6
Technology
Krell HEAT, or High End Audio Theater, is a design application
incorporated into Krell components to enhance multi-channel
home entertainment systems. A KrellHEAT system is an inte-
grated home theater system consisting of a state-of-the-art
Krell preamp/processor and matching amplifiers and loud-
speakers that reproduce two-channel and multi-channel sources
with audiophile sound quality, placing listeners in the middle
of a lifelike environment.
The crossover consists of a dedicated circuit board for each
group of drive units (woofers, midranges, and tweeters). Each
crossover network employs impedance correction circuitry
that flattens impedance curves and damps the resonance of
the drive units it controls, allowing the filter circuits to operate
under nearly ideal conditions.
KrellHEAT
Crossover
Definition of Terms
Following are the definitions of key terms used in your owner’s reference manual.

continued
7
Unpacking and Placement
This section describes the procedures for safely unpacking and placing your Lossless
Acoustic Transducers (LATs).
Opening the LAT–1000 and the LAT–C1000 Shipping Crate
The LAT–1000. Each LAT–1000 shipping crate measures 24 in. (61 cm) wide by
61 in. (155 cm) high by 24 in. (61 cm) deep and contains one LAT–1000. The
combined weight of the crate and loudspeaker is approximately 340 lbs. (155 kg).
Each LAT–1000 loudspeaker measures 12.5 in. (31.8 cm) wide by 54.6 in. (138.7
cm) high by 14 in. (35.6 cm) deep with an estimated weight of 270 lbs. (122.7 kg).
The LAT–C1000. Each LAT– C1000 shipping crate measures 44.8 in. (113.8 cm)
wide by 28 in. (71.1 cm) high by 23.25 in. (59 cm) deep. The combined weight of
the crate and loudspeaker is approximately 300 lbs. (136.4 kg). Each LAT–C1000
loudspeaker measures 40.9 in. (103) cm wide by 12 in. (30.48 cm) high by 15 in.
(38.1 cm) deep with an estimated weight of 200 lbs. (90.9 kg).
Krell recommends that three to four people are needed to safely move the loud-
speaker to its place in the listening area. Two people are needed to remove the
shipping crate top from its base.
The shipping crate is specially designed to open safely and easily. The LAT–1000
is enclosed in a protective sleeve and rests on the reinforced base of the crate,
and the crate top is fastened to the base with Phillips-head screws. The only
tool needed to remove the LAT from the crate is a Phillips screwdriver. See the
steps below to unpack the LAT.
To Remove the LAT–1000 or LAT–C1000 from the Shipping Crate
1. Locate the screws on the base of the shipping crate (two on each end and
three on each side). These screws are circled with black marker for easy
identification.
2. Completely remove all screws.
1 person needed
SECTION TWO

8
(SECTION TWO: Unpacking and Placement continued)
3. With one person grasping each end of the shipping crate, pull steadily straight
up. The crate top will slowly slide up and off. Set crate top aside.
2 people needed
The loudspeaker sits in a protective sleeve on the crate base. On top of the
loudspeaker is a wooden grille box that is shrink-wrapped.
A packet containing the Owner’s Reference and warranty card is affixed to the
top of the grille box.
4. Lift the grille box off the loudspeaker and set aside.
1 person needed
5. Carefully lift the loudspeaker out of the crate (do not remove the protective
sleeve at this time) and place it on the floor.
3-4 people needed
In the LAT–1000 grille box, with the grille, you will find:
4 stainless steel spikes
1 bubble level
2 binding post knobs
1-7/16 in. nut driver
In the LAT–C1000 grille box, with the grille, you will find:
2 shoulder screws
2 locator bolts
4 socket head cap screws
2 binding post knobs
1-7/16 in. nut driver
Inside the LAT–C1000 crate, at the bottom, there are 2 cardboard boxes containing
the loudspeaker foot and leg assembly and pivot mechanisms.

continued
Opening the LAT–2000 Shipping Box
The LAT–2000. Each LAT–2000 shipping box measures 15.8 in. (40.1 cm) wide by
19.3 in. (49 cm) high by 20.3 in. (51.6 cm) deep. The combined weight of the ship-
ping box and the loudspeaker is approximately 100 lbs. (45.5 kg). Each LAT–2
loudspeaker measures 10.5 in. (26.7 cm) wide by 14 in. (35.6 cm) high by 15.5 in.
(39.4 cm) deep with an estimated weight of 70 lbs. (31.8 kg).
The LAT–2000 is shipped with the loudspeaker grille installed.
To Remove the LAT–2000 from the Shipping Box
The LAT–2000 shipping box includes a 2-part cardboard assembly: 1) an interior
cardboard box with flaps and 2) a cardboard cap which surrounds the interior box.
To open the shipping box easily and safely, follow these steps:
1. Position the box so that the box opening instructions are on the top.
2. Cut the 4 bands of plastic strapping that secure the shipping box.
3. Lift the cardboard cap straight up and off the shipping box, exposing the interior
cardboard box, a shallow box with generous flaps. The flaps are secured by
plastic strapping. A packet containing the Owner’s Reference and warranty card
is affixed to a top layer of foam packing.
4. Cut the band of plastic strapping and fold the flaps open.
5. Remove the top layer of foam packing, exposing the LAT–2000 in its protec-
tive sleeve, surrounded by foam packing.
6. Remove the foam packing by gently lifting the packing straight up and out of the
interior cardboard box. You now see the entire LAT–2000 in its protective
sleeve, positioned on a bottom layer of foam packing.
7. Lift the LAT–2000 out of the shipping box by grasping the base of the loud-
speaker sides. Avoid contact with the grille. Do not use the binding posts to
lift the loudspeaker.
Notes
The LAT–2000 weighs 70 pounds. It may be more convenient for two people to lift the
loudspeaker out of the shipping box.
9

10
Placement
All loudspeakers interact with the environment in which they are placed. Loudspeaker
performance is influenced by the size, shape, and contents of the listening room as
well as the placement of the loudspeaker within the room.
Krell encourages you to experiment and find the loudspeaker placement that reflects
your personal preference. A Lossless Acoustic Transducer (LAT) is simple to set
up and use. Its unique solid aluminum enclosure produces a soundstage that is both
deep and wide, with little or no toe-in required. The closer a loudspeaker is to the
rear wall, the more pronounced the bass response. To minimize unwanted reflected
sound and maximize the width and depth of the soundstage, be careful not to set
the loudspeakers too close to the side walls.
3-4 people needed
When the loudspeakers are in position, you are ready to attach the loudspeaker
grille, see page 11, install the spikes on the LAT–1000, or install the foot and leg
assembly and pivot mechanisms on the LAT–C1000, see page 13.
(SECTION TWO: Unpacking and Placement continued)

To Attach the Loudspeaker Grille
Attach the grille to the loudspeaker before you play music. Each Lossless Acoustic
Transducer (LAT) is equipped with a snap-on grille, which consists of the grille
cord strung between two metal blocks. The grille is shipped in the accessory box
marked “grille”. To install the grille, follow these steps.
1. Grasp the grille blocks on each end of the grille, and lift the loudspeaker grille
out of the grille box.
2. On the LAT–1000 and LAT– 2000 loudspeakers, position one grille block on the
bottom front of the loudspeaker.
On the LAT–C1000 loudspeaker, position one grille block on the left front of the
loudspeaker.
3. Gently guide the grille locator pins into the two grille holes on the bottom front
of the loudspeaker.
On the LAT–C1000 loudspeaker, position one grille block on the left front of the
loudspeaker.
4. Grasp the remaining grille block, allowing it to rest between the thumb and fore-
finger of each hand.
5. Pull firmly to stretch the grille cords, until the grille locator pins align with the
two holes on the top front of the loudspeaker.
On the LAT–C1000 loudspeaker, stretch the grille cords to the right.
6. Gently guide the pins into the grille holes. You hear a click when the grille is in
place.
11
(SECTION TWO: Unpacking and Placement continued)
continued

To Detach the Loudspeaker Grille
The loudspeaker grille remains in place while you play music. However, if you wish
to move the loudspeaker, first detach the loudspeaker grille.
1. Grasp the grille block attached to the top front of the loudspeaker.
On the LAT–C1000, grasp the grille block attached to the right side of the loud-
speaker.
2. Gently pull the grille bar straight out, so that the grille locator pins slide out of
the grille holes.
3. Remove the grille block from the bottom front of the loudspeaker, by pulling it
straight out.
On the LAT–2000, remove the grill block attached to the left side of the loud-
speaker, by pulling it straight out.
4. To protect the grille, Krell recommends placing it back in the grille box until
you are ready to reinstall it.
Notes
Be careful not to scratch the surface of the loudspeaker with the grille locator pins.
Clean the grille periodically to remove accumulated dust. Gently wipe the grille from top to
bottom using a soft, dry, lint-free cloth. Do not use rubber conditioner or solvent.
12
(SECTION TWO: Unpacking and Placement continued)

To Install the Spikes on the LAT–1000
Each LAT–1000 is shipped with 4 stainless steel spikes: two rear articulating
spikes (with knob) and two (one long and one short) front stationary spikes (no
knob). Use these spikes to stabilize and level the loudspeaker. These spikes are
particularly important for sound quality if the loudspeaker will be placed on a
carpeted floor. The longer front spike is for deep-pile carpeting.
IMPORTANT
Do not install spikes until the loudspeaker has been placed in the listening area.
1. Insert the rear articulating spikes (with knobs) into the holes provided on the back
of the loudspeaker base.
2. Turn knobs by hand until they are secure (do not over-tighten).
3. Tilt the loudspeaker back just enough to insert the front stationary spike (no knob).
IMPORTANT
Two people are needed to safely tilt the loudspeaker to install the front stationary
spike.
4. Turn the front spike by hand until it is secure (do not over-tighten).
5. Place the bubble level on the loudspeaker cap.
6. Adjust the rear articulating spikes until the bubble indicates the loudspeaker is
level.
To Install the LAT–C1000 Foot and Leg Assembly and Pivot Mechanisms
1. Bolt the socket head cap screws through the screw holes on the foot and into
the right leg.
2. Insert the shoulder screw through the right shoulder screw hole on the right leg
and into the pivot hole on the right cap and hand tighten.
3. Move to the left side and repeat steps 1 and 2, to install the left leg and left
shoulder screw.
4. Adjust the angle of the LAT– C1000 and insert the locator bolt through the leg
and into the locator hole in the cap, one side at a time.
13

14
SECTION THREE
Anatomy of a Loudspeaker
This section describes LAT features and benefits.
Figure 1 LAT–1000 Front Panel and Grille
1 Cap
2 Driver (Tweeter)
3Drivers (Midrange)
4 Cabinet Material
5Proprietary Drivers
(Woofers)
6 Spikes
7 Base
8 Grille
9Grille Block
10Grille Holes
11 Ribbed
Configuration
12 Port
13 Logo Plate
14 Loudspeaker
Binding Posts
15 Midrange/
Tweeter
Sub-enclosure
(gray area)
16Tuned Port
(gray area)
17 High pass
Crossover
18 Band pass
Crossover
19 Low pass
Crossover
1
6
5
4
2
3
7
8
9
10
10
11 11
11 11

Figure 1, continued LAT–1000 Back Panel, Tuned Port, Enclosure, Crossovers
continued
15
14
12
13
+
-
15
16
P1
P1
M6
M6
C3 C3
C4C4
C1C1
M8M8
C5C5
C6C6
C2C2
C7C7
C9 C9
C8C8
IN +IN +
M7M7
M6M6
P2
P2
M1M1
C10 C10
P25003 P25003
M2M2
Krellindustries (c) June, 2000Krellindustries (c) June, 2000
M13
M13
IN -IN -
M9M9
C15 C15 C14C14
C13C13
P3 P3 P4
P4
C16
C16
C17C17
C12 C12
R5
R5
C11 C11 R3
R3 R2R2 R1 R1 R4R4
R8 R8
R7 R7
R6 R6
M10M10
C18C18C19C19
M11M11
C20C20 C21C21
R14 R14
L2L2
M12M12M12M12
C22
C22
C24C24
C23C23
M20M20M22M22
OUT +OUT +
R12 R12 R11
R11
P5P5
M12M12
R19 R19 R20
R20
M22M22
R15 R15 R17
R17 R18
R18
R16 R16
M20M20
OUT - OUT -
P4 P4 P6P6
R13 R13
M3M3 M4M4
R9
R9
M5M5
R10 R10
P6P6 M6M6
OUT -OUT -
M21M21
OUT +OUT+
M6M6
P5P5
C29C29
C30C30 P3P3
C26C26 C27C27
C31C31
C28C28
M23M23M21M21
L1 L1
M18M18
C32 C32
C33 C33
M16M16M9M9
R12R12 R13R13 R14R14
L1L1
M8M8
C22C22
C23C23
C24C24
C25C25
R1R1 R2 R2
M7M7M4M4M4M4
C21C21 C20C20
C16
C16
C17 C17
C14C14
C18
C18
C15C15
C19C19
L3 L3
M19M19
R11 R11
R8 R8 R10
R10
R9 R9
M17M17M15M15
R5R5 R4 R4 R3 R3 R7R7 R6R6
M14M14
L4 L4
C3 C3 C13C13
M13M13M12M12M12M12
C4 C4
P25002P25002
M3M3
Krell industries (c) June, 2000Krell industries (c) June, 2000
C2C2 C11C11
IN - IN -
M2M2
M13M13
P2P2
C8C8 C7C7
P8
P8
R5R5
M12M12
R1R1
R2
R2
R3
R3
P7
P7
C3
C3
P6
P6
C4
C4
C5C5
R6R6
M11
M11
R4R4
C9C9
C8C8
C7C7 C2C2
C6C6
C1
C1
OUT +
OUT +
C10 C10 C12 C12 C9C9
M10M10
C5 C5
IN +IN +
C6 C6 C1C1
P1P1
M6M6
M6M6
P5
P5
P4
P4
P3
P3
L2
L2
M6
M6
M5M5
M4
M4
Krell industries (c) June, 2000Krell industries (c) June, 2000
P25001P25001
OUT -OUT -
M10
M10
M9
M9
L1
L1
M8M8P2P2
IN -IN -
M3
M3
M2
M2
P1P1
IN +IN +
M1M1
17
18
19