KROSS STUDIO WATCH WINDER User manual

KROSS STUDIO WATCH WINDER
USER MANUAL

TABLE OF CONTENTS
Unboxing & regular care
Tech specs
Assembly
Starting up
Winding cycle launch
General specifications
Replacing the batteries
3
4
5
6
7
8
9

User manual 3 KSWAW22 kross-studio.com
UNBOXING & REGULAR CARE
UNBOXING
Thank you for purchasing Kross Studio watch winder.
As the winder weighs approximately 2kg, it
is important to take extreme caution when
manipulating it. Handle it with care as negligent
manipulation might alter the precision of the winder.
The box and the thermoforming foams have been
conceived for safe transportation.
In order not to alter the winder during transport, the
winding motor is not assembled to its support in the
packaging.
We guide you to assemble your watch winder on
page 5 of this manual.
REGULAR CARE
Clean your product by wiping it down carefully with
a soft microfiber cloth.
If needed, you may use a solvent-free cleaner to
spray on the cloth. Do not spray any liquid directly
on the winder.
The watch winder is designed for use in a temperature
range from 10˚C to 40˚C (50˚F to 104˚F). Using
your winder at low temperatures can significantly
decrease the battery life.

3
5
1
4
2
6
User manual 4 KSWAW22 kross-studio.com
The watch winder has a system that allows the maintaining of the automatic mechanism
of your watch.
It is equipped with an infrared sensor that detects the presence of your watch. When
there is no watch inside, the device remains in standby mode to avoid battery usage.
Please refer to the diagram above for all instructions listed.
Length 130mm
(5.1 inches)
Width 150mm
(5.9 inches)
Height 215mm
(8.5 inches)
Weight 2kg
(4.4 pounds)
TECH SPECS
Model Name
Kross Studio Aluminum
Watch Winder
Limited Edition
Reference
KSWAW22
Material
Anodized aluminum
Parts
26
Power
4 Lithium/Alkaline
AA 1.5V (LR6) batteries
Rotation speed
13.6 turns/minute
Battery life
Around 2 years
Configuration
Refer to page 9
KROSS STUDIO WATCH WINDER
General
Overview
WINDING CASE FUNCTIONING
Dimensions
KROSS STUDIO KEY
Head
Vertical satin-finished steel
Shaft
Mirror-polished steel
1Watch support
2 ON/OFF LED button
3Central screw
4Winding case
5Battery location
6Kross Studio key

User manual 5 KSWAW22 kross-studio.com
ASSEMBLY
Kross Studio watch winder is equipped with two
elements: the winding motor and its support, from
which it can easily be disassembled in order to be
stored while winding a watch.
Follow the instruction below to safely assemble your
watch winder:
1. Press the LED ON/OFF button (2) 2 times to reset
the winding motor
This button must be placed at 9 o'clock when the
winding motor is in its support
2. Insert the winding motor in the support by placing
the screws in front of the matching notches
3. Block the winding motor by turning it to the right
until you feel a resistance
To remove the motor from the base, pivot it to the left
and carefully remove it.

2
User manual 6 KSWAW22 kross-studio.com
STARTING UP
To turn on your watch winder, press the ON/OFF
button (2). The white LED indicator lights up to
confirm that it is turned on. The device will not turn
on while the button is held down.
The LED indicator flashes to indicate the battery
charge level:
4 flashes: full charge
3 flashes: 60% charge
2 flashes: 30% charge
A flash every 2 seconds means it is time to change
the batteries.
To replace the batteries, refer to the procedure
page 9.
Note: Regardless of the presence of a watch, at
startup, the winder will perform a partial rotation
in order to re-align to its vertical position, followed
by a full rotation to indicate you that it is functioning
properly.
Caution: Never manually turn the rotating watch
support.
Always stop the motor when removing or attaching
the watch to the winder.

1
4
2
User manual 7 KSWAW22 kross-studio.com
Before following the procedure below, make
sure that the winder is turned off to prevent it from
rotating.
To do this, press again the ON/OFF LED button
(2). If the unit was turned off, it will turn back on
and indicate the battery life level. Then turn off the
winder again
Note: After the ON/OFF LED button is released,
the LED brightness will gradually fade to dark,
indicating to the user that the winder is turning off.
1. Remove the watch support (1) by unclipping
it in line with the winding case (4).
2. Position your watch in the centre of the
watch support. Adjusting the bracelet
may be necessary. Note: if there is no watch
on the watch support, the cycle cannot start.
3. Clip again the watch support while having
your watch on the watch winding, making
sure that the watch indicates midday
upwards.
4. Before starting the cycle, make sure that
the watch winder is positioned horizontally
or in a 30-degree angle.
5. Push the ON/OFF LED button to initiate the
start of the cycle.
WINDING CYCLE LAUNCH

User manual 8 KSWAW22 kross-studio.com
The watch winder is pre-configured.
To select another configuration that matches your
watch model, we invite you to download the Kross
Watch Winder app on the App Store or Google
Play Store.
GENERAL SPECIFICATIONS
Please check your app regularly for upgrades and
new features.
Once in the app, just select the caliber that matches
your watch model.
The application allows the configuration of the
winding system using the iPhone or Android
Bluetooth low energy (Bluetooth Low Energy or BLE)
technology.
APPLICATION SPECIFICATIONS
• For devices compatible with Bluetooth 4.0
(Bluetooth Low Energy/BLE) technology.
• For iOS 10 and higher platforms
• For Android 5 and higher platforms
• 8 languages available
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.*
Google, Android, Google Play, and other marks are trademarks of Google LLC.*
*Supported features may vary between platforms and countries with compatibility subject to change.

X 4
5
1
3
4
2
6
User manual 9 KSWAW22 kross-studio.com
REPLACING THE BATTERIES
When turning on your watch winder, if the LED
button flashes once every 2 seconds, it means that
you have to change the batteries.
To replace the batteries, proceed as follows:
1. Remove the watch support (1) by unclipping
it in line with the winding case.
2. Using the Kross Studio key supplied with
your watch winder (6), remove the central
screw (3) by turning the key anticlockwise.
3. Once unscrewed, carefully remove the
winding case (4).
4. Insert 4 Lithium/Alkaline AA 1.5 (LR6)
batteries in their designated location (5),
beware the polarity (check the markings).
5. Replace the winding case carefully
respecting the central shape of the structure.
6. Replace the central screw (3) with the
Kross Studio key (6) while holding the winding
case in place.
7. Press the ON/OFF LED button (2) to check
that the device is recharged and can start a
new cycle. Make sure the ON/OFF LED blinks
4 times after the ON/OFF button is released,
meaning that the batteries are fully charged.
Note: The cycle will only start with the presence of a watch on the support.
We recommend to remove the batteries if you do not use your case for a long time.

User manual 10 KSWAW22 kross-studio.com
WARRANTY
Your rotating winding case is guaranteed for two
years from the date of purchase. Register your
product online on kross-studio.com to be granted
a 3-year warranty extension. (total 5 years)
The warranty covers the free replacement or repair
of your winder resulting from manufacturing defects,
provided that these defects are clearly established
as such. It does not cover cleaning work, normal
wear and tear of the device as well as damage due
to external causes or improper use.