KRUSE KRUSEGO User manual

The KRUSEGO Multilingual System
OPERATING INSTRUCTIONS

PLEASE READ THIS IMPORTANT INFORMATION
BEFORE USING THE KRUSEGO SYSTEM
CHARGING THE KRUSEGO RECEIVERS
When charging the KRUSEGO Receivers, ALWAYS ENSURE THE CASE IS OPEN. If the case lid is closed during
recharging the air movement restriction will cause heat build-up and result in overheating and render the system
unusable.
Note: When charging, a red light glows in the headphone connector socket. When fully charged the red light goes
out.
KRUSEGO RECEIVERS
When placing the KRUSEGO Receivers in and out of the recharger, they simply slot in with a VERY GENTLE push. Do
not force the KRUSEGO Receivers into the recharger case as this will break the connectors in the base of the
recharger case. If a connector breaks it cannot be replaced easily.

THE KRUSEGO TOUR MASTER
SETTING UP FOR EACH TOUR
1. Attach and lock the KRUSEGO Tour Master and suction mount to the vehicle windscreen by turning the
levers on the base of the suction mount until they click and lock into place

2. Squeeze two of the vertical the X-GRIP levers to open the X-GRIP and insert the KRUSEGO Tour Master as
demonstrated in the picture. Once released, the X-GRIP will hold the KRUSEGO Tour Master as shown in the
bottom picture.
3. Turn on the KRUSEGO Tour Master using the ORANGE Power button at the bottom left of the keypad. The
KRUSEGO Tour Master will now display “SYSTEM READY”. Push the BLUE “TOUR”Button. The display will
now read “SELECT TOUR” with the default “NONE”. Push the ARROW UP button until the desired tour is
reached. Press the PLAY/PAUSE Button and the display will now read “ON TOUR” for the selected tour.
Shortly the screen will blink intermittently; this is “power save mode” to save battery power.

4. When the KRUSEGO Tour Master has obtained GPS lock, the GPS Icon at the top right of the screen display
will change from GPS Xto GPS .
5. When the KRUSEGO Receivers have been turned on, set to the required tour and languages, given to the
passengers and the tour is ready to commence. (Instructions for setting up the KRUSEGO Receivers for a tour
are on the following pages)
If the selected tour commences with manually triggered “INTRODUCTION” commentary, the procedure to
manually play the Introduction commentary is as follows:
Push the SAFETY button at the bottom right of the KRUSEGO Tour Master. If the display is flashing, the
KRUSEGO Tour Master is in “power save mode”. To activate and play an Introduction commentary in
“power save” mode, push the Safety button 2 X until the display shows “Select Safety Msg”. Use the
ARROW UP and ARROW DOWN buttons to scroll through the list of manually triggered commentaries
until the desired “INTRODUCTION” commentary is displayed.
Firmly push the BLUE Play/Pause button ONCE to play the “INTRO” commentary. “Triggered” appears in
the display to confirm the instruction to play the “INTRO” commentary has been transmitted to the
KRUSEGO Receivers. Once activated, the KRUSEGO Tour Master Screen will revert to blinking and display
“ON TOUR” and the selected tour and the GPS status.
GPS COMMENTARY TRIGGERING
When GPS Lock is obtained (GPS ) the KRUSEGO Tour Master will automatically send the instruction to the
KRUSEGO Receivers to play the commentary relating to the vehicle’s location as the vehicle passes through a
GPS trigger point.
MANUAL COMMENTARY TRIGGERING
All manually triggered commentaries are stored under the SAFETY button. To activate ANY manually triggered
commentary the procedure is basically the same as Step 6 above.
i.e. Push the SAFETY button at the bottom right of the KRUSEGO Tour Master. If the display is flashing, the
KRUSEGO Tour Master is in “power save mode”. To activate and play any manually triggered commentary when
the KRUSEGO Tour Master is in “power save mode”, push the Safety button 2 X until the display shows “Select
Safety Msg”. Use the ARROW UP and ARROW DOWN buttons to scroll through the list of manually triggered
commentaries until the required commentary is displayed.
Once the required commentary is displayed, firmly push the BLUE Play/Pause button ONCE to play the selected
commentary (“triggered” appear in the display to confirm the instruction to play the selected commentary has
been transmitted to the KRUSEGO Receivers). Once activated, the KRUSEGO Tour Master Screen will revert to
blinking and display “ON TOUR”, the selected tour and the GPS status.

THE KRUSEGO RECEIVERS
SETTING THE LANGUAGE
1. Turn the KRUSEGO Receivers on by SIMULTANEOUSLY pushing the MENU and POWER buttons. The
KRUSEGO Receivers screen will default to “Select Tour” and one of the tour names”.
2. Scroll through the tours using the volume up/volume down button until the desired tour is displayed. Then
press the MENU Button to confirm the tour.
3. The screen will now display SELECT Language and the last language that the KRUSEGO Receiver was set too.
4. Use the “Volume Up” and “Volume Down” buttons to toggle though the languages until the desired
language is displayed. Once the desired language is displayed, push the MENU button to confirm the
language choice. The Kruse Receiver screen will display the word “READY” and is now set for the tour.
Note: If the receivers are collected back partway through the tour and placed back in the recharger they will
automatically turn off. When resuming the tour, STEPS 1 and 2 to set the language will need to be configured
again.
SETTING THE VOLUME
1. To adjust the volume, use the Volume up and Volume down buttons. The Kruse Guide screen will display the
volume level as it is changed
2. At the end of each tour, the Kruse Master Controller and Kruse Receivers are shut down either by holding
the POWER button (the display will show “SHUTDOWN” and then count down 3 seconds before finally
powering off) or simply place the Kruse Master Controller and Kruse receivers into the recharger and they
will shut down automatically.

FCC Compliance
This device complies with part 15 of the FCC rules and regulations.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference
that may cause undesired operation.
Under no circumstances should you try to open your KRUSEGO multilingual
system hardware and modify it internally. Unauthorised repairs may
permanently damage the equipment and void your authority to operate this
device under Part 15 regulations.