KSR Siena Assembly instructions

Drg No. KSR5281-IS-C
12.06.2019 MAC
Installation Sheet
10W Triple CCT LED
KSR5281
Read these instructions before commencing installation &
retain them for future reference.
i
Available finish:- Black
General Maintenance
General maintenance and cleaning should be performed at least quarterly.
Clean product outer using a damp cloth, the glass can be cleaned with hot soapy water,
dried and buffed to a shine. After any maintenance remember to check all seals are
intact. Grease screws and nuts with a suitable waterproof repellent to ensure trouble
free operation in the future.
Installation Procedure
Ensure mains supply is turned off. Locate luminaire, use the mounting
bracket as a template to drill fixing holes. Secure the bracket into position using
suitable fixings. Prepare wiring, using suitable cable for the application. When securing
this product to a wall, please remember to allow enough cable to tilt the luminaire to its
final resting position. Never allow the mains wiring to become strained.
Remove the terminal cover from the back of the fitting.
Terminate the wiring and select the CCT colour you require using the switch (Never
switch the CCT colour while powered up as this can damage the LED chips).
Class I Product so this luminaire must be earthed.
Reinstall the terminal cover ensuring the seal is in place and seated correctly.
DO NOT use power drivers to tighten terminal cover screws as this can cause
damage to the terminal cover and invalidate the warranty!
Finally, adjust the angle of tilt to the required position and tighten bolts.
Turn mains supply on and test luminaire.
Adjust the settings you require on the PIR see overleaf.
Lamp Details
Lamp: 10W Triple CCT 3000K, 4000K or 6000K
Lumen Output:
3000K - 735 lumens
4000K - 875 lumens
6000K - 815 lumens
CRI: >Ra80
These fittings are Class I and must be Earthed
LED Floodlight with PIR
IP65
Important User Advice
Always switch off mains supply before servicing.
Important Information
It is recommended that luminaires are installed and fitted by a qualified electrician
ensuring the installation complies with current IEE wiring regulations & local building
control. These products are designed for connection to a 240V 50Hz supply.
Any broken or damaged parts should be replaced as soon as possible.
KSR will not accept responsibility for any claims arising from a poor installation.
KSR Lighting Aftersales: 023 92 674343
E-mail: [email protected]
240V~50Hz
Brown - Live
Green/Yellow - Earth
Blue - Neutral
Live
Earth
Neutral
240v
Supply Luminaire
Connections
Siena CCT
1.0m
113mm
126mm
164mm
90mm
44mm
64mm
KSR Lighting Ltd, Unit E Hazleton Interchange, Lakesmere Road, Hampshire, PO8 9JU
The light source of this luminaire is not
replaceable; when the light source
reaches its end of life the whole
luminaire shall be replaced

PIR Controls
Read these instructions before commencing installation &
retain them for future reference.
KSR Lighting Aftersales: 023 92 674343
E-mail: [email protected]
KSR Lighting Ltd, Unit E Hazleton Interchange, Lakesmere Road, Hampshire, PO8 9JU
PIR Specification
Detection Range: 120°
Detection Distance: 2~10m(adjustable)
Time Delay: 10sec ±5sec ~ 7min ±2min (adjustable)
Ambient Light: <3 ~ 2000 LUX (adjustable)
Detection Motion Speed: 0.6-1.5m/s
Working Temperature: -10°c ~ +40°c
Working Humidity: <93%RH
Installation Height: 1-3m
Override Mode: Yes
PIR Adjustments
SENS
-+
LUX
TIME
+
-
Description of Operation
This floodlight comes complete with an passive infrared detector. The lamp
switches on when movement in the surrounding area is detected or when
natural day light becomes dusk. Ensure to replace any cracked shield / glass.
Operation Mode
When power is switched on, the PIR detector enters into the warm up
period (approx 15-30 seconds), the PIR will then change to the AUTO MODE
automatically, during the AUTO MODE walk testing can be easily carried out.
WALK TESTING: Before walk testing, please put the LUX control to the day
position ( ) and the TIME control to minimum (fully clockwise). Once the PIR
sensor receives a valid trigger signal (such as body movement) within its
detection area, the load / lamp will be turned on for a duration time, You will
obtain the desired detection area by walking slowly through the area to be
covered.
Adjusting the Lux Control Level
The LUX control module has an in built sensing device (photocell) that
detects daylight ( ) and darkness ( ) Rotating the LUX control anti-clockwise
will take it from light to dark, set at desired level. Note: You will need to wait
5 secs for the stability of the photocell (CDS) when adjusting the LUX control.
Adjusting the Duration Time
The length of time sensor remains on after activation can be adjusted from
10 secs to 9 mins. Rotate the TIME control clockwise to increase the duration
Note: Once the load has been triggered by the PIR detector any subsequent
detection will restart the time period.
Adjusting the Sensitivity
With this control the sensitivity of the detector can be adjusted, turn the SENS
control anti-clockwise to increase the sensitivity.
Manual Overide
With the floodlight powered on, switch the power off and then back on in less
than 3 seconds. This will overide the sensor and the light will stay on.
To revert back to auto mode power off the floodlight for more than 5 seconds
and power back on.
iLED Floodlight with PIR
Siena CCT
Please Note: After adjusting the PIR please ensure the locking
tab that allows you to adjust the angle of the PIR is tightened
correctly to ensure the fitting is rated to IP65 failure to do this
could result in water ingress and premature failure of the
luminaire.