KT&C KPC-HDB650 User manual

M171-HDB650-001
HD CCTV
Digital Video Camera
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
NAME AND FUNCTION
• LENS CONNECTION
Lenses are sold separatele. Lenses such as an auto iris lens,
CS-Mount lens and C-Mount lens can be used.
NOTE
• Please keep the lens clean.
• Any foreign objects and fingermarks on the lens can cause
inferior image quality in low light level conditions.
When using an auto iris lens
1.Please peel off about 8mm of the
outer skin of the auto iris lens cable.
2. Please peel off about 2mm of the
outer skin of the insulated conductor
inside the lens cable.
3. Please remove the cover of the auto iris lens connection plug and solder
the lens cable ti the connector pin in the plug.
*PIN ASSIGNMENT OF THE LENS CONNECTOR
Signal for DC + iris lens
Pin 1: DAMP-
Pin 2: DAMP+
Pin 3: DRV+
Pin 4: DRV-(GND)
Signal for Video + iris lens
Pin 1: Power source: +9 DC,50mA MAX
Pin 2: N.C(Not used)
Pin 3: Video Signal:0.7Vp-p/10K ohms.
Pin 4: Shield, ground
4. Please replace the auto iris lens connection plug cover and take off the
CCD protection cap and than attach the auto iris lens to the camera by
screwing it in clockwise.
Back Focus Procedure
Step 1 - Remove Lens Cover.
Step 2 - If using a C-Mount lenses it can be applied
to the camera at this time.
Step 3 - Most current lenses are CS-Mount and
require removal of the C/CS ring.
Step 4 - To remove the C/CS ring loosen but do not
remove completely the two set screws and
than remove the C/CS ring.
Step 5 - Screw on the CS-Mount lens until a good
picture is obtained and tighten the set screws.
Step 6 - Use the focus ring on the lens to obtain
a finer focusing
NOTE
- if a C-Mount lens was applied and focus could not be obtained, please try the following :
• Ensure that the lens is in face a C-Mount and not a CS-Mount.
•Check the focus adjust on the lens.
• if need be loosen the set screws and adjust the position of the lens
and C/CS ring as one unit until a good focus is obtained.
5. Please insert the connection plug that is connected to the auto iris lens cable into the
auto lens connector, which is located on the back of the camera
* As the connecting method varies with instruments, refer to the
manual supplied with the instrument.
* Only connect the cable when the power is turned off.
* Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modications in construction of this devies which are not
expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Caution -
CAUTION
1. A regulated DC12V 300mA power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When an unregulated power supply is applied, the product warranty will be
roid.
2. It is recommended that the camera is used with a monitor that has a CCTV
quality 75Ω video impedance level. If your monitor is switched to high impedance
then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
componets. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which
may cause smears on the picture and possible damage to the image sensor.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a main socket-outlet with a protective earth
connection.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
Note -
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
WARNING -
CAUTIONS CAUTIONS
WEEE
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working
life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources. Household users should contact either the retailer
where they purchased this product, or their local government ofce, for
details of where and how they can take item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
This product should not be mixed with other commercial wastes for
disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER(OR BACK). NO USER. SERVICING TO
QUALIFED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufcient mangnitude to constitute
a risk of electric shock.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
COMPONENTS
FRONT
BACK
CS-Mount
C-Mount
Lens Cover
Lens Cover
C/CS RING
INSTALLATION
• MONITOR CONNECTION
BNC FEMALE
(2'nd Video / Yellow)
BNC FEMALE
(HD-SDI Jack)HD-SDI IN
DC12V Power Supply
DC12V IN
(Black)
Monitor
①. ■ MENU BUTTON
▲ UP BUTTON
▼ DOWON BUTTON
◀ LEFT BUTTON
▶ RIGHT BUTTON
②. Auto IRIS Jack
CS-MOUNT ADAPTOR RING
Set Screw(Left Side)
AUTO
IRIS
OSD
CONTROL
①
②
HD CCTV Camera
Auto Iris Lens
Connection Plug
C-mount Adaptor Ring
Spare Screw (Machine 2x2) - 2ea
Operation Manual

OSD MANUAL
SPECIFICATIONS
DIMENSIONSUnit(mm)
MAIN MENU 1st Sub MENU 2nd Sub MENU 3rd Sub MENU 4th Sub MENU
EXPOSURE
BRIGHTNESS 0 ~ 20
LENS(IRIS) AUTO / MANUAL AE MODE
INDOOR / OUTDOOR
/ DEBLUR ( in Auto
Mode )
NORMAL / DEBLUR (
in Manual Mode).
RETURN BACK / EXIT
SHUTTER AUTO / MANUAL LEVEL
1/30(25),1/60(50),1/
120(100),1/240,1/50
0,
1/1K,1/4K,1/8K,1/16
K,1/30K,1/60K
RETURN BACK / EXIT
DSS Off / X2 / X3 / X4 / X5 / X6 / X7 / X8
AGC 0 ~ 20
RESET DATA BACK / DEF
RETURN BACK / EXIT
WHITE
BALANCE
WB MODE AUTO / AUTOext
/ PUSH / MANUAL
COLOR TEMP LOW / MIDDLE / HIGH
R-GAIN 0 ~ 20
B-GAIN 0 ~ 20
RETURN BACK / EXIT
SATURATION 0 ~ 20
RESET DATA BACK / DEF
RETURN BACK / EXIT
D-WDR /
BLC
OFF / BLC /
D-WDR
H-POS 0 ~ 20
V-POS 0 ~ 20
H-SIZE 0 ~ 20
V-SIZE 0 ~ 20
RETURN BACK / EXIT
DNR OFF / LOW / MIDDLE / HIGH
DAY &
NIGHT
AUTO/ COLOR /
B&W
AGC THRES 0 ~ 20
AGC MARGIN 0 ~ 20
DELAY LOW / MIDDLE / HIGH
RESET DATA BACK / DEF
RETURN BACK / EXIT
IMAGE
SHARPNESS 0 ~ 20
GAMMA 0.45 / 0.5 / 0.55 / 0.6 / 0.65
MIRROR OFF / ON
FLIP OFF / ON
DZOOM 1.0X / 1.1X / 1.2X / 1.3X …… 7.7X / 7.8X / 7.9X / 8.0X
DEFOG OFF / ON
MODE AUTO / MANUAL
LEVEL LOW / MIDDLE / HIGH
RETURN BACK / EXIT
LENS SHADING OFF / ON WEIGHT 0% ~ 100%
RETURN BACK / EXIT
RESET DATA BACK / DEF
RETURN BACK / EXIT
SPECIAL
FOCUS ASSIST OFF / ON
PRIVACY OFF / ON
ZONE NUM 0 ~ 15
ZONE OP OFF / ON
H-POS 0 ~ 60
V-POS 0 ~ 40
H-SIZE 0 ~ 40
V-SIZE 0 ~ 40
Y LEVEL 0 ~ 10
CR LEVEL 0 ~ 10
CB LEVEL 0 ~ 10
RETURN BACK / EXIT
HLMASK OFF / ON
LEVEL 0 ~ 20
COLOR BLK / WHI / YEL / CYN /
GRN / MAG / RED /BLU
RETURN BACK / EXIT
PATTERN OFF / ON
RESET DATA BACK / DEF
RETURN BACK / EXIT
SYSTEM
SDI FORMAT 1080P / 720P
FRAME RATE 30(60) / 25(50)
CVBS FORMAT NTSC / PAL
APPLY OK / ON
LANGUAGE ENG / CHN / CHN(S)
SYSTEM INFO
S/W VERSION
SET VERSION
RETURN BACK / EXIT
REBOOT
RETURN BACK / EXIT
Image Device 2.1 Mega Pixel, 1/3” Exmor SONY CMOS
Video output mode HD-SDI : 1080p@30, 1080p@25, 720p@60, 720p@50
TV Out : NTSC / PAL selectable
Effective Pixels 1984 (H) x 1105 (V)
Unit cell size 2.8um (H) x 2.8um (V)
S/N Ratio More than 50dB
Minimum Illumination 0.1 Lux
Video Output HD-SDI / 1.0 Vp-p Composite ( 75Ω ).
Lens C / CS Mount
Shutter speed Auto / Manual selectable
D-WDR / BLC Off / BLC / D-WDR
3DNR OFF / LOW / MIDDLE / HIGH
Controllable Max Gain 23 dB
White Balance AUTO / AUTOext / PUSH / MANUAL
Digital Zoom Ratio 1X ~ 20X
Digital Slow Shutter Off, X2 ~ X8
Privacy Masking Zone 16 ea , On / Off
Day & Night Digital Day & Night
OSD Built-in
Operating Temperature 14°F~112°F (-10°C~+50°C)
Storage Temperature -4°F~158°F (-20°C~+70°C)
Power Consumption DC12V (±10%), Max. 120 mA
Dimensions (mm) 31(W) x 31(H) x 55(D)
Weight Approx.113 g
Specications and designs are subject to change for improving the functionality of this product without notice.
CS-Mount
• Function Description
0. SETUP
- EXPOSURE: Go sub menu for camera exposure control.
- WHITE BALANCE: Go sub menu for camera white balance control.
- WDR/BLC: Go sub menu for camera WDR or BLC action.
- DNR: Control noise reduction setting.
- DAY & NIGHT: Go sub menu for camera day & night control.
- IMAGE: Go sub menu for adjust image functions.
- SPECIAL: Go sub menu for special feature control.
- SYSTEM: Go sub menu for system control & information.
- Reset Data All: Reset camera’s all feature data to default value.
1. EXPOSURE
- BRIGHTNESS: Adjust image brightness value.
- LENS(IRIS): Select Lens control Type.
AE MODE: Adjust AE control Mode.
- SHUTTER : Select shutter speed control type.
LEVEL Adjust shutter speed at manual shutter mode.
- DSS Adjust digital slow shutter control level.
- AGC: Adjust max gain level for brightness control.
2. WHITE BALANCE
- WB MODE: Select white balance control mode.
AUTO: Full auto control mode in color temperature rage 2300K~10000K
AUTOext: Extened auto mode for special illumination.
PUSH: Enable fix the control setting for specific environment. Push &
release, for fix WB control setting
MANUAL: Enable WB control setting by user’s intention.
>COLOR TEMP: Select color temperature range for WB control at
manual mode
>R-GAIN: Adjust red color gain for WB control at maual mode.
>B-GAIN: Adjust blue color gain for WB control at manual
mode
- SATURATION: Adjust image brightness value.
3. WDR/BLC
- MODE: Select WDR for BLC mode.
BLC: Act in Backlight compensation mode.
D-WDR: Digital wide dynamic range control.
- BLC H-POS: Select BLC control zone vertical position.
- BLC V-POS: Select BLC control zone horizontal position.
- BLC H-SIZE: Select BLC control zone vertical size.
- BLC V-SIZE: Select BLC control zone horizontal size.
4. DNR: Reduce image’s noise
5. DAY & NIGHT
- MODE: Select DN( Digital Day & Night control ) mode.
AUTO: Camera controlled automatically to decide day or night
environment using AGC calculation data.
COLOR:
Fix to mode at day environment setting. Make video image act in color.
B&W:
Fix to mode at night environment setting. Make video image act in B/W.
> AGC THRES: Threshold level for Change Day to Night or Night to
Day mode.
> AGC MARGIN: Hysteresis Level for Change Day to Night or Night to
Day mode.
> DELAY: Delay Time for change day or Night Mode at Auto
mode.
6. IMAGE
- SHARPNESS: Adjust image sharpness level.
- GAMMA: Gamma Curve Select.
- MIRROR: Vertical Mirror Setting.
- FLIP: Horizontal flip setting.
- DZOOM: Select digital zoom magnification.
- DEFOG: Enable Defog compensation.
LEVEL: Defog compensation Level change at Auto / Manual mode.
-LENS SHADING: Enable lens shading compensation.
7. SPECIAL
- FOCUS ASSIST: Adjust image sharpness level.
- PRIVACY: Gamma Curve Select.
ZONE NUM. : Select private mask zone number. V-SIZE : Select zone vertical size.
ZONE DISP. : Select zone mask display on/off. Y LEVEL : Select mask color ( Y Level ).
H-POS : Select zone horizontal position. CR LEVEL : Select mask color ( CR Level ).
V-POS : Select zone vertical position. CB LEVEL : Select mask color ( CB Level ).
H-SIZE : Select zone horizontal size.
- HLMASK: Mask image high light area.
LEVEL : Select high light level.
COLOR : Select mask color
- PATTERN: Color bar display Enable.
8. SYSTEM
- SDI FORMAT : 1080P / 720P
- SDI FPS: 30 or 25 fps in 1080p mode.
720P Mode : 60 / 50 fps.
- CVBS FORMAT : NTSC / PAL
- APPLY : Apply all video setting changed at once. Use the Set button to apply.
- SYSTEM INFO
S/W VERSION: Camera’s basic software version.
SET VERSION: Camera’s feature control setting version.
C-Mount