Kuezen DSA-1104 User manual

Disposer Manual
* The use of product is subject to special conditions including the preparation of purifying utilities,
the inner size, slant and length of plumb, etc.
* Please read this for right utilization before installation.
* This Manual contains Product warranty.

Instruction
Before the use, be sure to read this instruction to prevent subsequent damage or monetary loss
by following this manual.
Warning
Notice
This Mark says the misuse of this appliance may cause death or heavy
damage to body.
In case of misuse, Bodily or product damage may occur.
Warning
Don’t plug several electronic heaters
leading to over-capacity into electric
multi-inlet.
Prohibition.
Prohibition.
Prohibition.
Prohibition.
Complete observance.
Complete observance.
(It may cause a fire.)
Apply the over 220V(10A) plug only.
(It may cause a fire.)
Don’t touch the electric cord or plug
with wet hand or may
get you elasticized.
Don’t use the cord to draw out plug.
(It may cause the cable break.)
Don’t use the broken plug or Connector.
(It may get a fire.)
For disassemble, repair or
modify, don’t hire anybody
but the technician
we recommend.
No disassemble.
(It may cause a fire,
damage or disorder.)
Don’t do any work hurting the cable like
processing, forcefully bending, twisting,
binding, inserting.
(It may cause electrified or out of order.)
Don’t put a hand in while working.
Be sure to use it with it covered with lid.
Careful in handling
(Severely hurt your body.)

Careful
Careful
Don’t plug several electronic heaters
leading to over-capacity into electric
multi-inlet.
Prohibition.
(May do damage to product.)
Don’t pour hot water or oil into it.
Prohibition. (It may do severe damage to product.)
Don’t put the magnetic things near
the product.
Prohibition. (It may get malfunction or hurt.)
Do not use this to dispose glass,
metal or hard objects.
Prohibition. (It may do a severe damage to product.)
Do not see product working too near.
Careful.
(The object out of the product may
hurt your body.)
Do dispose too much at a time in
cooking a big dish for a special day.
Careful.
(Overload can cause a fire or
out-of-order. )
Children or the handicapped is not
allowed to use this product.
Prohibition. (It can hurt you.)
Please check the water
leakage of connection spots
before running it.
Careful.
(The leaked water may
wet the floor.)

The name or Function of parts
The name or Function of parts
The structure of the product
Assembly diagram
Outer cover
Grinding hopper
Safety inner cover
This prevents the garbage from
jerking out and reduce the noise.
It inserts and keeps contents.
Sink flange
It fixes the main body to the
sink bowl.
Repairing handle
It is used to assemble, dissemble
or initiate the grinding hopper.
Breaking chamber
The place where the garbage
breaks.
Dual breaking structure.
Power-on switch
This is the on/off switch.
Turntable set
It uses centrifugal force
to break the content.
Grinder ring set
It induces and breaks
the content.
Rubber ring
It absorbs vibration.
Main body
It is equipped with power
motor and motion sensor.
Over-flow hose
It drains the overflowing
water from sink.
Lower hose
Malodor blocking cap
It seals and fixes lower
hose to sewage pipe.
Complex collecting
chamber
It blocks stink and reflux,
and filters and discharge
the larger particles.
Body gasket
Sink Flange Gasket

• Space to be installed in, especially for product height.
<Operation unit>
<Sensor unit>
Revolving Cover
Fig. A
Fig. B
Fig. C Fig. D
Magnet
Magnet cover
Strain Block
Fixture supporter
Washer
Joint screw
Sensor unit
housing
limit sensor
• Check the location of sewage pipe, especially for the length(1m) of lower hose.
• Check the electricity –Input voltage, current. Check the sink bowl – the drain hole size.
• The space to install on/off switch in(Up/Down Ø45.
First, please dissemble a sink flange
and a grinding hopper from main
body and locate the sink flange at
the center of sink drain hole.
Second, put main body under the
sink bowl, synchronize sink flange
and main body, turn them to fasten
up at the maximum, and then align
the side connecting part of the main
body to the overflow hole of the sink
bowl.
Third, turn the grinding hopper
clockwise and fix it to the sink flange.
First, turn the Revolving cover clockwise as to reached
the strain block. Second, peel protective film off the
operation unit and then make the smile shape even to
the sink bowl in the left and right direction. And then
paste it as in Fig. A.
First, after power-on, grasp sensor unit as in the fig.B
and joint it to the operation unit under the sink bowl.
(Be sure to match N of operation unit and left part of
limit sensor.
Second, after peeling off the detachable
paper of sensor unit and checking it’s working,
connect them.
1) It runs for 15 seconds at a time. Please
repeat it as in Fig. C for re-operation.
2) When the operation finishes, turn the
switch to ‘OUT’ as in Fig.D.
Installation
Installation
Check lists before installation
The installation of main body
Installation and operation check of turn switch

First, please connect overflow to drain
hole of sink bowl with screw, connect
‘Y’ pipe to complex drain drum, and
then connect upper tube to “Y” pipe.
(if the hose is too long to hang loose,
cut off the upper part of hose as to be
hang tight. Second, fasten the lower
tube to complex drain drum, measure
the distance between sewage tube on
the floor and complex drain drum and
then cut off the tube to this length, put
odor preventative cap around the tube
at 120mm up from the lower end and
then insert that tube into the sewage
Third, pipe and fix it. After cover the cap
on the disposer, fill the water to check
the leakage of overflow packing, and
open the cap to check leakage of body
gasket and connecting spots.
Drain should be completed within 60
seconds on the basis of 20 liters.
1) Direct the operation display of sink flange toward
rear of the sink bowl, insert the main body under the
sink bowl and then fasten up at the maximum
toward the overflow.
2) As in left fig., turn the disposer main body so that
the operation display of sink flange and the limit
sensor to meet together.
3)
Hose connection, leakage and
drain test.
Installation of cover switch and check of operation.
ON OFF
Installation
The sewage pipe
Fig. A
120 m/m
Cap
Magnet
Sink Flange
Main body Limit sensor
Sensor cover
of Cap switch.

Specification of models
Specification of models
Assembly
diagram
(m/m)
Power
Power
consumption
Grinding
capacity
Rounds
per minute
Monthly Power
consumption
Switch
Style
Water
consumption
noise before
oprearation
main
material
Running
time
Product
size
Weight
controller
Foot step
Continue
110W 320W 320W 200W
15sec 15sec 15sec
Turn/Cap Turn/Cap Turn/--

Alert! When you open grinding hopper and deal the inside of the grinding
chamber, do measures after pulling the power cord off, and start it again
with hopper shut close for sure.
Disorder Symptom and Check, Measures
Disorder Symptom and Check, Measures
Not working.
Noise and Vibration is too high.
Drain is too bad.
It makes a heavy bad odor.
Emergent measures
• Please make sure that power cord is connected.
• Check whether there is debris in the grinding hopper or it is overloaded, remove
them with forceps.
• If the power motor runs over 5 minutes, it gets overheated and stops automatically,
but it starts again after cooling.
• Putting abnormal substance makes no grinding, noise and vibration.
Please remove abnormal substance.
• First, check the blocking of ‘Y’ connector and complex converging drum, reuse it
after removing abnormal substance.
• Check the winding drop of the hose due to too long hose. If any, please cut off the
useless part to get it tense.
• Open the grinding hopper to wash it clean.
• When you can’t use sink due to sink’s not working, remove hopper and discharge
substances and then, utilize a general filter net for a while and the wait the A/S
person to come in.

How to use and maintain
How to use and maintain
Check before Grinding
Operation
The normal maintenance
1. Make sure whether the object is food waste.
1. Let water flow by releasing the water tap.
2. Start to dispose by putting a small quantity of food waste and turning power switch clockwise
at the same time. (cover style switch runs when the mark ↑ of the cover meet at the location
“operatioin” of sink flange and stops when it departs.)
3. Evem after Grinding Noise(about 80㏈) ends, this appliance completely stops after more
15 seconds(1 stroke) running. This is the end of one operation.
4. Shut the water supply off.
1. Maintain well to prevent unpermitted from inserting.
2. When you dispose a large quantity of food waste out of refrigerator clean-up or party,
please treat it by a little bit.
3. Do not use this for the other purpose except for the treatment of food waste.
4. This appliance uses the pressure incurred from the spinning of turn-table double blade to
clean up the inside. So, do not use the additional cleanser, deodorants corroding stainless
machine parts.
5. This appliance is made of plastic so that the use of hot water or high temperature oil incurs
distort, only to breakdown.
6. Once in a month remove the debris in the breaking room and the composite collecting
chamber and wash up.
2. Check the leakage of the connecting spot of hoses.
3. Check the safety cover is shut.
Treatable wastes. Edible, cooked (rice, noodle, vegetable, fruit, tea waste, meat,
fish etc.)
Untreatable
general wastes.
Inedible, seeds(Plum core, Peach core etc.), Shells(nut, chest nut,
corn stalk, pine apple waste, banana etc.), others(bone, fish, clam,
clothe, vinyl bag, cover, wire, string, aluminum foil, wood teaser,
decoration etc.)
• Put a adaptable quantity through
inlet not so as to overflow it.
• Washing is made by the pressure
that spinning double blades apply.
• The application of cleanser or
deodorant causes corrosion.

Other appliance parts
Other appliance parts
Multi-cap(protrusion)
Multi-cap(embedment)
Cover switch(disposer)
Connector ‘S’ drain trap 50 ‘S’ drain trap 25Nut cap
Disposer
Cleaner
Composite
Collecting Fitering Drum Net
The composite
collecting drum
Composite collecting
cover