Kullhaus AERO+ User manual

User manual
AIR PURIFIER IONIZER
AERO+
Thank you for choosing this product.
Please read this instruction manual before using it.

2
Table of Contents
Safety Instructions ................................................................................................................ 3
Product Description ............................................................................................................... 4
Control Panel Description ..................................................................................................... 5
Operation Instruction ............................................................................................................ 6-8
Operation with Remote Control ............................................................................................ 9
Clean & Maintenance........................................................................................................... 10-11
AERO+ lter system ............................................................................................................. 12
Specications ....................................................................................................................... 13
Only for domestic use
The device is allowed to be used only for its prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not the manufacturer will be liable for any dam-
age or injuries of any kind resulting from such misuse.
Read the user manual before any use, refer to the corresponding section in this user manual.
Recycle unwanted materials instead of disposing of them. All appliances and packaging
should be sorted and tendered at a regional recycling centre and be processed in an ecologi-
cal manner.
The product conforms to the applicable European and other directives.

3
Safety Instructions
• To avoid electric shock, re or injury, please read the user manual carefully before using the appliance and keep it for future
reference.
• Please use suitable power source with 230V~50Hz.
• Do not to pull or tug the power cord to switch off the appliance, otherwise it will cause re or get an electric shock accident.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in
order to avoid hazard.
• Please do not insert any foreign objects into any crevices of the unit in order to avoid electric shock.
• Please keep the air inlet and the air outlet unblocked. The appliance should be used at minimum distant of 30 cm from the
wall.
• Do not overload your power supply with multiple power plug, otherwise it will cause re or get an electric shock accident.
• Forbid to put ammable and explosive objects around the machine, and do not use the appliance in an environment full of
ammable gas and powder. Keep away from any re and heat sources in order to avoid short circuit or re.
• Keep the appliance away from direct sunlight or any heat source or any spillage area, this appliance is for indoor use only.
• With any indication of malfunction, please stop using the appliance immediately to avoid hazard or re. Contact the author-
ized service center for repairing. Do not attempt to repair or change any parts by yourself.
• When the appliance is not in use for a prolonged period, please turn it off, unplug it.
• Please turn off and unplug the appliance before cleaning or maintenance.
• Please operate the appliance on rm location, to avoid accidental collision and damage to the product.
• Do not use the appliance at any spillage area. When any water spilled/dropped into the appliance, it may cause a re or
electric shock hazard
• Before using the product, please remove all the lter packaging and ensure that the lter of the product is properly installed
in accordance with the manual.
IMPORTANT SAFETY INSTRUCTIONS – READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

4
Product Description
1. Front Panel
2. Filter
3. Dust Sensor
4. Display Indicator
5. Power ON/OFF Switch
6. Air Outlet Grille
7. Handle
8. Fan Speed Button
9. VOC Sensor
10. Filter Lock Switch
11. Filter Lifting Bracket
12. Remote Control

Control Panel Description
Button Function
Power switch
Fan speed button
Press fan speed button for 3s to lock all buttons
Press fan speed button for 10s to switch spacer scanning function
Press power button and fan speed button to reset the lter
Indicator Function Indicator Function
Timer indicator Display of air quality (green/yellow/red)
Negative ion indicator Display of PM2.5 value
Filter exchange indicator Display of VOC Value
Automatic mode Quick smoke removing indicator
5
Before starting up
Remove the front cover, take the main lter out of the plastic lm and insert it back into the device. Please see the
steps at chapter ,,Filter change”.

Pic. 1
Operation Instructions
1. Switch Function:
Press the ON/OFF button (pic.1) or wipe slowly over the power button with your hand by keeping a distance of
3-5cm (pic.2) to turn on or turn off the appliance. Every operation is accompanied by a sound.
Note: After connecting to the power supply ,the appliance starts automatically a 60 seconds countdown. During this
time the air cleaner is doing a one-time analysis of the air quality. After the countdown the LED display shows the
current PM2.5 value and activates the negative ion function. In addition, the VOC sensor is activated after a 320
seconds countdown. Touch the power button again, the unit enters into standby mode. If you turn the appliance on
again within ve minutes the PM2.5 and VOC values will be shown directly.
Remark: PM2.5 and VOC values are displayed in turn every 5 seconds. (Pic.3)
Note: After the power supply is connected, with a beeping sound, the appliance will enter into the
standby mode. Analysis of room air quality, odour and CO2 detection, will start working.
Pic. 3
Pic. 2
6

2. Filter Replacement Indicator:
The appliance features a lter replacement indicator (pic.4). After 2000 operation hours a ashing indicating light will show on
the LED display which indicates that the lter needs to be changed. Please note that the operation time is rounded up to the
next half hour. Example: If you have used the appliance for 40 minutes, it will be counted as 1 hour. To reset the operation time
counter after exchanging the lter, press and hold the ON/OFF button as well as the FAN SPEED button for 3 seconds at the
same time. The indicating light will ash 6 times during the reset and turn off.
3. Child lock function (Shared with the fan speed button)
When the air cleaner is working, press the FAN SPEED button for 3 seconds to lock all buttons on the panel and remote control.
The same operation can unlock it.
Remark: Besides the power button, other functions are invalid
4. Fan Speed
Press the FAN SPEED button to select between A-1-2-3-A (automatic). The fan speed icon will display for 5 seconds (pic.5), and
show the PM2.5 value.
Remark: Press the FAN SPEED button again can check the current fan speed setting.
5. Wiping Sensor
If you want to deactivate the wiping sensor (pic.2), press and hold the FAN SPEED button for 10 seconds (pic.6). To reactivate
the wiping sensor, repeat the process.
6. Optical Light Sensor Function
When the appliance is in a dark environment, it will enter automatically into sleep mode after 1 minute. When the environment is
bright again, the sleep mode will be deactivated after one minute.
Remark: Please note that this function can only be used when the AUTO mode is activated.
Pic. 4 Pic. 6
Pic. 5
7

Based on the measured PM2.5 and VOC values, you can choose a suitable fan speed by using the following tables
or you can use the AUTO mode which regulates the performance level automatically:
PM2.5 in ug/m³ 0-75 76-150 151-500
Air quality level Good Medium Bad
Fan Speed 1 2 3
Light colour Green Yellow Red
1. PM2.5 value
VOC value
VOC in mg/m³ 0-0.60 0.60-1.00 > 1.00
Air quality level Good Medium Bad
Fan Speed 1 2 3
Light colour Green Yellow Red
2. When the CO2 up to 1800ppm, the yellow color light starts ashing, please open the window for ventilation.
8

Operation With Remote Control
Reminder: When using the remote control for the rst time, install two no. 7 batteries for using.
The remote control can be used to set the same function, as on the appliance. Please note that some functions can
only be controlled with the remote control. They are listed below:
Functions controlled only with the remote control.
Turbo Function-HIGH SPEED: Please press this button to activate the turbo function. When the function is active,
“H” will be shown on the display and after 5 seconds the PM2.5 value will be shown in alternation. Press the button
again to deactivate the turbo function.
Negative Ion Function: When pressing this button the negative ion function can be activated and deactivated.
ON/OFF Button for LED Display Light: If the LED display light is turned off, only the ON/OFF button will be lit.
When pressing this button again, all indicating lights will light up again.
Sleep Mode: During sleep mode, all sounds and lights are turned off except from the ON/OFF button. Only the ON/
OFF button and the SLEEP button can be operated.
9

• Always disconnect the appliance from the power outlet and let it cool before cleaning. Never immerse the appli-
ance in water to prevent electric shocks.
• Wipe over the exterior of the appliance with a soft wet cloth and then wipe dry with a dry cloth.
• Please do not use any chemicals or other abrasive cleaning agents, such as steel wool, to clean
• Depending on the pollution degree, the lter should be replaced after 6-12 months. To do so, please refer to
below steps.
1. Remove the Front Panel
a. Press the upper clasp with both hands lightly;
b. Pull the front panel out;
c. Lift the front panel up.
Cleaning & Maintenance
10