Kunbus DF PROFI II PCIe User manual

DF PROFI II PCIe
Installation Instructions
V1.6
27.02.2017
Project No.: 5302
Doc-ID.: DF PROFI II PCIe
KUNBUS

h:\dokumente\project\5302_df_profi_ii\anwenderdoku\installation\pcie\kunbus\version_1.5\df
profi ii pcie_e.doc
Revision History
Version
Date
Description
V1.6
27.02.2017
KUNBUS branding
V1.5
30.07.2013
New Declaration of Conformity added
V1.4
23.09.2009
Technical data table extended
V1.3
04.08.2009
Document-Adjustment
V1.1
29.07.2008
CE Declaration corrected
V1.0
21.05.2008
Initial Version
KUNBUS GmbH
Heerweg 15c
D-73770 Denkendorf
Phone [phone]
Fax [phone]
Copyright 2017 by KUNBUS GmbH
This document is protected by copyright. Reproduction, duplication, publishing, transfer or disclosure of the
contents of this document are only permitted after prior written agreement has been obtained from KUNBUS
GmbH.

DF PROFI II PCIe - Installation Instructions Contents

KUNBUS V1.6 / 27.02.2017 i
Contents
1 Installation of the Board................................................................................................1
2 Safety Instructions........................................................................................................2
3 Pin Assignment.............................................................................................................3
4 Description of the LEDs................................................................................................4
5 Technical Data..............................................................................................................5
6 Declaration of Conformity .............................................................................................6

Contents DF PROFI II PCIe - Installation Instructions
ii V1.6 / 27.02.2017

KUNBUS
List of Figures
Figure 1: DF PROFI II PCIe Board.........................................................................................1
Figure 2: PROFIBUS Terminator ...........................................................................................3
Figure 3: Declaration of Conformity, page 1...........................................................................6
Figure 4: Declaration of Conformity, page 2...........................................................................7
Figure 5: Declaration of Conformity, page 3...........................................................................8
List of Tables
Table 1: Pin Assignment........................................................................................................3
Table 2: Technical Data.........................................................................................................5

DF PROFI II PCIe - Installation Instructions Installation of the Board

KUNBUS V1.6 / 27.02.2017 1
1 Installation of the Board
The DF PROFI II PCIe is a plug & play compatible board for PCI Express Slots. The
configuration entirely takes place by means of the delivered software or the BIOS of your PC
respectively. Thus, no jumpers or DIP-switch adjustments are necessary.
To mount the board, please proceed as follows:

Switch off your PC and unplug the mains plug!

Remove the screws of the PC cage and lift off the cover. If necessary,
please see also the operating instructions of your PC.
Select a free PCI-Express X1 slot.

Remove the slot cover and plug the DF board into the determined slot. Pay attention
to a proper adjustment of the board in the guidance (avoid canting!).

Screw down the board.

Fix the cover again and screw it down.
Remark: When mounting, please follow the safety instructions for
electronic modules against electrostatic charge.
Figure 1: DF PROFI II PCIe Board

Safety Instructions DF PROFI II PCIe - Installation Instructions
2 V1.6 / 27.02.2017

KUNBUS
2 Safety Instructions
WARNING: Disregarding this
warning may result in damage to
equipment and/or serious personal
injury. Only qualified personnel may
start up and operate this device.
According to the safety instructions in
this text, qualified personnel are
persons who are authorized to start
up, to ground, and to mark devices,
systems, and equipment according to
the standards of safety technology.
In addition, these persons must be
familiar with all warning instructions
and maintenance measures in this
text.
WARNING: FNL is designed
exclusively for PELV operation
according to EN 60950 / EN 60204 /
VDE 0805-1. Only protective extra-
low voltages according to the defined
standards may be used to supply
and connect the alarm contact.
Shielding
The shielding ground of the
connected twisted pair cables is
electrically connected to the female
connector. When connecting network
segments, avoid ground loops,
potential transfers, and voltage
equalization currents via the braided
shield.
i
NOTE: Electrostatic discharge!
The device contains components that
can be damaged or destroyed by
electrostatic discharge. When
handling the device, observe the
necessary safety precautions against
electrostatic discharge (ESD), in
accordance with EN 61340-5-1 and
EN 61340-5-2, as well as
IEC 61340-5-1 and IEC 61340-5-2.
i
Housing
Only staff authorized by KUNBUS is
permitted to open the housing.

DF PROFI II PCIe - Installation Instructions Pin Assignment

KUNBUS V1.6 / 27.02.2017 3
3 Pin Assignment
Pin Number
Signal
Function
Direction
1
-
shielding
3
RxD/TxD-P
Data+
Input/Output
5
0V (potential free 80 mA)
Feeding of bus terminator
Input
6
5V (potential free 80 mA)
Feeding of bus terminator
Output
8
RxD/TxD-N
Data-
Input/Output
Table 1: Pin Assignment
Remark: To assure correct operation of the PROFIBUS, a terminating resistor must be
mounted at each bus end (Purchase No.: 4000-7-002-H).
Figure 2: PROFIBUS Terminator
220 
390 
390 
0V
Data-
Data
+
+5V
150 
390 
390 
Cable type A
Cable type B

Description of the LEDs DF PROFI II PCIe - Installation Instructions
4 V1.6 / 27.02.2017

KUNBUS
4 Description of the LEDs
Green LED:
On: Firmware loaded and started
Off: Firmware not loaded
Yellow LED:
On: PROFIBUS started
Off: PROFIBUS stopped
Red LED:
On: PROFIBUS-Failure (min. one slave not connected to the bus or with external
diagnosis)
Off: No PROFIBUS-Failure

DF PROFI II PCIe - Installation Instructions Technical Data

KUNBUS V1.6 / 27.02.2017 5
5 Technical Data
Processor
Net+Arm 40, 33 MHz
PROFIBUS Controller
ASPC2, 48 MHz
Memory
1 Mbyte SRAM
2 Mbyte Flash Type Memory
PCI Interface
PCI-Express X1
PROFIBUS Interface
1 * Sub-D 9 pins
Interface Physics
RS485 (isolated)
PROFIBUS Data Rates
9600 Bit/s - 12000 KBit/s
Data Size of Process Image
max. 8 KByte
PROFIBUS Isolation Voltage
500 VDC
Power Consumption
+5 V / 1100 mA
Ambient Temperature Range
0 - 55 °C
Dimensions
175 mm * 107 mm
Table 2: Technical Data

Declaration of Conformity DF PROFI II PCIe - Installation Instructions
6 V1.6 / 27.02.2017

KUNBUS
6 Declaration of Conformity
Figure 3: Declaration of Conformity, page 1