EK 804.2 7
Conditions o guarantee
The conditions o guarantee applicable or this product are subject to those
published by the representative in the relevant country. Details regarding same
may be obtained rom the dealer rom whom the appliance was purchased.
For claims under guarantee the sales receipt must be produced.
Please note
KÜPPERSBUSCH built-in ovens may be combined only with KÜPPERSBUSCH
built-in hob units. The use o any other make o hob unit shall exempt Küp-
persbusch rom all liability. Failure to observe this requirement will inva-
lidate all granted certificates and labels of approval. For operating
instructions and sa ety instructions regarding the hob unit, please re er to the
operation manual or the relevant oven or circuit element.
Notes on disposal
Disposing of the packaging
The transport packaging consists o the ollowing materials:
corrugated cardboard, cardboard, Styro oam (CFC ree), Polyethylen oil and
wood (untreated).
Do not put these materials in the household rubbish, but ask your local au-
thority to give you the address o the most convenient collection point.
What to do if you happen to have an old applicance
Old appliances contain many materials which can be recycled. For this reason
you should not simply put your old appliance on the rubbish tip, but ask your
local authority how it might be recycled.
Electrical Connection
■ The built-in cooking area must be connected to the mains supply by
a qualified electrician who is authorized to carry out such work.
Both legal wiring regulations and the requirements of your local elec-
tricity supply board must be fully complied with.
■ When connecting the appliance, please provide a device which makes it
possible to isolate the appliance rom the mains with a contact gap o at
least 3 mm. Suitable isolating devices are line protecting circuits, cut-outs
and contactors.
■ Both the control unit and the oven must be isolated rom the mains during
installation.
– Switch o at the use box or remove the use.
– Make sure that the multiple pin plug belonging to the hob unit is cor-
rectly inserted into the matching socket o the control unit.
Hints on installation
■ It is absolutely essential that the worktop is aligned horizontally and that a
clean cut is made into it!
■ The clearances between the worktop cut-out and the wall must be the same
as in ig. 2, at the ront, at the back and at the sides.
A corner moulding o solid wood may be itted to the worktop at the back
o the hob unit provided that the minimum clearances are maintained.
For practical reasons the lateral clearance between the hob unit and an ad-
jacent tall cupboard unit must measure at least 300 mm.
■ Make sure that there is su icient clearance underneath the cut-out. Any ur-
niture battens must be cut away to leave an area which is at least the same
size as the cut-out itsel .
■ We recommend a similar set-up to the one shown in ig. 1.
■
Make a point o ensuring that the plastic laminate or wood veneer on your urni-
ture surround has been applied by means o a heat-resistant adhesive (100 °C).
■ The underside o the installed appliance must be protected by a panel which
prevents inadvertent contact with the live parts or connecting leads between
the control unit and the hob unit (see igure 6).
It must not be possible to remove the panel without tools.
■ Any cooker hoods or wall cupboards must have a vertical clearance o at
least 650 mm rom the hob unit.
It will be expedient to seal built-in sinks and other built-in appliances in the
worktop in the same way (protection against ingress o water).
Prior to installation and a ter removal or repair, examine the gasket or pos-
sible damage. The gasket must provide per ect contact on all our sides. Re-
place it i necessary.
In the case o ceramic-tiled worktops it is necessary to provide an additional
seal with the aid o a permanently elastic sealing compound. Such sealing
compound can be purchased as Küppersbusch spare part No. 53 55 69.
– Clean the sur aces to be sealed in accordance with the manu acturer's
instructions on the cartridge. Apply the compound in a continuous strip,
pressing it irmly against the gap to be sealed.
– Cut away any surplus sealing compound with a sharp kni e and clean
the sealed joint with water.
Installation o glass-ceramic hob units
Using clips makes it easier and quicker or you to install these units. You can
carry out the complete installation work rom above.
■ Always li t the cooking sur ace by holding it at the sides. Do not li t it by
the ront bar.
■ Be extremely care ul when installing! Do not place or drop any sharp or
pointed tools (screwdrivers etc.) on the glass sur ace!
■ The glass-ceramic cooking area must have a level and lush bearing. Any
distortion may lead to racture o the glass panel.
– First o all make a clean cut into the worktop (see igure 2).
– Make sure that the gasket is properly seated. I the worktop sur ace is
uneven (tiles etc.), remove the gasket strip and seal with a heat resistant
sealing compound.
– Then insert the clips into the worktop cut-out as shown in igures 3 and
4, observing the clearances indicated in ig. 2. It is not necessary to ad-
just the height due to the horizontal stop motion device. I a worktops
should have a thickness o 30 mm or less, the clips must be screwed
down as shown in ig. 5.
– Connect the oven/circuit element and the hob unit.
– Now position the cooking sur ace on the le t as shown in ig. 7, align it
(2) and clip it in (3).
I the worktop cut-out should be a little too large,
it is possible to increase the preliminary spring
tension o the clips by screwing them down.
You only require the enclosed tension el-
em ents S i you are itting the hob unit into
worktops made o granite, marble or sim-
ilar materials. I the worktop is thick, rotate
the tension element in such a way that the
narrower angle grips the underneath o
the worktop.
Granit etc.
