Kuppersbusch EEBP 6200.8 MX Owner's manual

Guía Rápida de Uso
Folha de Características
Feature List
Feuille de Caractéristiques
Datenblatt
EEBP 6200.8 MX

21
ENGLISH
CONTROL PANEL
1Door lock. When this pilot light is on, it indi-
cates that the oven door is locked and can-
not be opened.
2Function selector.
3Electronic clock.
4Temperature selector.
EEBP 6200.8 MX
1Control Panel
2Fixing to Unit
3Oven Seal
4Grill element
5Chrome Support +
Telescopic Guide
6Grid
7Cake Tray
8Roasting Tray
9Hinge
10 Door
11 Air cooling outlet
12 Door switch-lock
13 Grill Screen
14 Smoke Outlet
15 Light
16 Rear Panel
17 Fan
12:00
3
2
4
6
7
8
9
10
5
12
11
13
15
14
16
17
1
21 3 4

22
0Switch off oven
Conventional
It is used for sponges and cakes where the
heat received must be uniform to achieve a
spongy texture.
Conventional with fan
Appropriate for roasts and cakes. The fan
spreads the heat uniformly inside the oven.
Grill
For preparing dishes with superficial roasting.
It allows the outer layer to be browned without
affecting the inside of the food. Ideal for flat
food, such as steaks, ribs, fish, toast.
MaxiGrill
Allows greater surfaces to be prepared, than
with the grill, together with higher power redu-
cing the time required for browning of the food.
MaxiGrill with fan
Allows uniform roasting at the same time as
surface browning. Ideal for grills. Special for
large volume pieces, such as poultry, game,
etc. It is recommended to put the item on a
rack with a tray beneath to collect the stock
and juices.
Caution
While using the Grill, MaxiGrill or MaxiGrill with
fan, the door must be kept closed.
Turbo
The fan distributes the heat coming from an
element located at the back of the oven. As a
result of the evenly distributed temperature,
food can be cooked on two levels at the same
time.
Lower Element with Turbo
Ideal for baking pizzas, pies, and fruit tarts or
sponges.
Lower element
Heats only from beneath. Suitable for heating
dishes and raising pastry and similar.
Defrosting
This cooking mode is suitable for gently defros-
ting of food. In special food to be consumed
unwarmed, e.g.: cream, custard, pastry, tarts,
cakes, fruit, etc.
Pyrolytic Function
This programme allows you to carry out a
pyrolytic cleaning cycle which involves the oxi-
disation and carbonisation of grease accumu-
lated during cooking, through the high tempe-
ratures that are reached inside the oven.
During the cleaning cycle the light inside the
oven will remain off.
NB
The light remains on through all cooking func-
tions except the pyrolytic function.
Oven Functions

23
ENGLISH
Note
The electronic clock features Touch-Control
technology. To operate, simply touch the glass
control symbols with your fingertip.
The touch control sensitivity continuously
adapts to changing conditions. Ensure that
the glass front control surface is clean and
free of any obstacles when turning on the
oven.
If the clock does not respond correctly when
you touch the glass control, it will be neces-
sary to turn off the oven for a few seconds
and then turn it back on. By doing this, the
sensors adjust automatically and will react
once more to fingertip control.
Setting the Electronic Clock
When you connect the oven, you will notice
that 12:00 will flash and the symbols and
light up. Set the clock by touching the
or symbols on the glass. You will hear 2
beeps confirming the time has been set.
To change the time, touch the and
symbols together until the indicated time
flashes on the display. Adjust the time with
the or symbols.
The two beeps you hear after that will confirm
the new time has been set.
Manual Operation
After setting the clock, the oven is ready for
use. Select a cooking temperature and func-
tion by pressing and turning the oven controls.
To turn off the oven, set the controls to 0.
Push down on the controls to conceal them.
Pre-heating function (not valid for pyrolytic
function):
For any cooking function or when the oven is
being heated for the first time (pre-heating),
on the timer display you will see the following
instructions light up consecutively:
When the temperature that you have selected
has been reached, 5 consecutive beeps will
sound indicating that the oven has finished
pre-heating.
Electronic Clock functions
Timer Alarm: An audible signal is produced at
the programmed time, even if the oven is not
being used.
Cooking Time: This function allows you to pro-
gramme cooking time length, after which the
oven will turn off automatically.
Cooking Stop Time: This function allows you
to programme the time for cooking to stop,
after which the oven will turn off automatically.
Cooking Time and Cooking Stop Time: This
function allows both cooking time length and
the stop time to be programmed. The oven
turns on automatically at the set time and
operates for the cooking time it has been pro-
grammed for. It turns off automatically at the
programmed stop time.
Child Safety Function. This function locks the
oven, preventing small children from playing
with it.
Use of the Oven

24
Programming the Timer Alert
1Touch the symbol on the glass surface.
It will begin to flash. 0:00 will appear on the
display and the and will light up.
2Set the alarm time by touching the or
symbols.
32 beeps will then be heard. The symbol
will flash and the display will show the time
left before the alert sounds.
4An alarm will sound at the end of the pro-
grammed time.
5Touch any symbol to stop the alarm. The
symbol will turn off.
You can change the timer at any time by tou-
ching the symbol and later the and
symbols. They will then light up. The two
beeps you hear after that will confirm the new
time has been set.
Programming Cooking Time
1Touch the symbol on the glass surface.
It will begin to flash. 0:00 will appear on the
display and the and will light up.
2Touch the or symbols to programme
the cooking time.
32 beeps will then be heard. The symbol
will flash and the display will show the time
left before the oven switches off automati-
cally.
4Select a cooking function and temperature.
5When the set cooking time is over, the oven
will turn off and an alarm will sound.
6Touch any symbol to stop the signal. The
oven will turn on again.
7Set the controls to 0to turn off the oven.
You can change the timer at any time by tou-
ching the symbol and later the and
symbols. They will then light up. The two
beeps you hear after that will confirm the new
time has been set.
Programming the Cooking Stop Time
1Touch the symbol of the glass surface.
It will begin to flash. The current time will
appear on the display and the and
will light up.
2Touch the or symbols to programme
the cooking stop time.
3The alarm will be confirmed by two beeps
and the display will show the current time,
while the symbol will remain lit to indi-
cate that the oven will switch itself automa-
tically.
4Select a cooking function and temperature.
5Once it is the set time, the oven will turn
off, an audible signal will sound and the
symbol will flash.
6Touch any symbol to stop the signal. The
oven will turn on again.
7Set the controls to 0to turn off the oven.
You can see the set cooking stop time by tou-
ching the symbol. You can then also chan-
ge the timer setting by using the and
symbols, which will light up. The two beeps
you hear after that will confirm the new time
has been set.
You can use this function even if you are coo-
king with the oven. If this is the case, follow
all of the above instructions except No. 4.

25
ENGLISH
Programming Cooking Time and Cooking
Stop Time
1Touch the symbol on the glass surfa-
ce. It will begin to flash. 0:00 will appear
on the display and the and will light
up.
2Touch the or symbols to program-
me the cooking time.
32 beeps will then be heard. The
symbol will flash and the display will show
the time left before the oven switches off
automatically.
4Touch the symbol of the glass surface.
It will begin to flash. The current time will
appear on the display and the and
will light up.
5Touch the or symbols to program-
me the cooking stop time.
6This will be confirmed by two beeps. The
current time will show on the display and
the symbol will light up.
7Select a cooking function and tempera-
ture.
8The oven will remain off with the and
symbols lit up. The oven is program-
med.
9When it is time to start cooking, the oven
will switch on and will operate for the pro-
grammed cooking time. The symbol
will flash.
10.At the set stop time the oven will switch
off, an alarm will sound and the and
symbols will flash.
11.Touch any symbol to stop the signal. The
oven will turn on again.
12.Set the controls to 0to turn off the oven.
You can change the timer setting while coo-
king. First touch the or symbols. Then
touch the or to change the set time.
Child Safety Function
To activate this function, touch the ,
and symbols simultaneously. You will hear
one long beep and see a lit dot moving on the
clock display. The clock is locked.
Activating the child safety function with the
oven off (with control settings on 0) will stop
the oven from being turned on. If the safety
feature is activated with any cooking function
in operation, it will only lock the electronic
clock settings.
To deactivate the function, touch the ,
and symbols simultaneously. You will hear
one long beep.
Caution
In the event of an electrical short circuit, all
the electronic clock programmed settings will
be cancelled and a 12:00 reading will flash on
the display. Reset the clock and programme.

26
PROGRAMMING AND OPERATING THE PYROLYTIC FUNCTION
Follow the instructions below to carry out a
pyrolytic cleaning cycle:
1 IMPORTANT: Remove all accessories
(shelves, grids, side supports to hold up
the shelves, telescopic guide rails) from
inside the oven.
2Turn the cooking control dial to Pyrolysis
position .
3Next, press the key, the word PIRO
should appear on the timer display.
4After a few seconds, on the timer display,
you will see the P2 indication (programme
2 of the pyrolytic function).
5You can now change the pyrolysis program-
me to P1, P2 or P3 by pressing the or
keys:
P1: Minimum programme. Duration 1 hour
P2: Standard programme. Duration 1 hour
and 30 minutes
P3: Maximum programme. Duration 2
hours
6You will hear 2 consecutive beeps after
several seconds or by pressing the key
confirming the chosen programme.
7After a short time, you will see the time
remaining for the selected programme to
end and the symbol lit up on the timer
display. The pilot light will turn on and
the oven door cannot be opened, as the
heating will have begun.
IMPORTANT: At this point, the oven is pro-
grammed and the pyrolytic cleaning cycle is
underway. During the cycle, none of the timer
functions can be selected, except the child
lock. Do not try to open the oven door as it
may interrupt the cleaning process.
8When the pyrolytic cleaning cycle has finis-
hed, an alarm will sound, the symbol
will flash and you will see the correct time
on the display.
9Press any of the timer’s keys to disable the
alarm.
10 Set the cooking control dial to position 0.
11 The oven’s heating process has ended,
however the oven is extremely hot and can-
not be used. The cooling motor will opera-
te until the oven cools down, pilot light
will remain on and the symbol will flash
on the timer display.
IMPORTANT
The cooling process may last up to 2 hours
owing to the high temperatures inside the
oven.
12 You will be able to open the oven door a
short time after the pilot light turns off.
IMPORTANT
To open the door (pilot light on), the control
dial must be in position 0. If you did not follow
instruction 10 set the control dial to position 0
and wait a few minutes until the door unlocks
and the pilot light switches off.

27
ENGLISH
CANCELLING THE PYROLYTIC CYCLE
Pyrolysis is an automatic function and therefo-
re can only be activated from the timer pro-
gramme. To cancel a cleaning cycle it is neces-
sary to reset the oven, following the instruc-
tions below:
1Set the function control at 0and wait for 1
minute.
2Unlock the oven door.
1 Set the function control at 0 and wait for
1 minute. The oven will no longer heat up.
2 Unlock the oven door. To cancel the clea-
ning cycle, the oven door must be unloc-
ked. To do so, consider the following:
a) Unlocking the door 45 minutes after
the cleaning cycle. If the oven has been
operating for more than 45 minutes, the
door will unlock automatically once the
oven has cooled down to the safe tem-
perature. Then, pilot light will switch
off.
b) Unlocking the door in the first 45 minu-
tes (at a low temperature). Within the
first 45 minutes the oven door will
unlock automatically. Follow the instruc-
tions below:
1Turn the control dial to position .
2Wait for approximately 1 minute.
3Turn the control dial to position 0.
4Approximately, 1 minute later pilot
light will turn off and the oven
door can be opened.
13 Open the oven door and wipe the inside
with a damp cloth, cleaning up the ash
from the cleaning cycle. Areas in the oven
that are difficult to access will need to be
cleaned with a non-metallic fibre scourer.
14 Once the oven is clean, do not forget to
replace the supports and accessories.
15 The oven is now ready to be used.
IMPORTANT: If any incidents are detected in
the programming and operating of this func-
tion, consult the section “Incidents while
Operating the Pyrolytic Function”.

28
INCIDENTS WHEN OPERATING THE PYROLYTIC FUNCTION
INCIDENT CAUSE SOLUTION
My accessories and shelf
supports are damaged.
You have not removed the
accessories and supports
during the pyrolytic cleaning
cycle.
You must replace them and
remove them in later cleaning
cycles.
The enamel colour has
changed and stains have
appeared.
The chemical composition of
some foodstuffs may cause
changes in the enamel.
This is normal and does not
damage the properties of the
enamel.
The oven door is locked, pilot
light is lit up but the oven
is not hot.
You have turned the control
dial to position and no
other additional operation has
been performed.
Switch off the oven and follow
the instructions to unlock the
door in the first 45 minutes at
a low temperature.
Next, select the pyrolytic
function, carefully following the
instructions.
I have turned the control dial
to position , pressed the
key, I can see the P1, P2
or P3 on the display but the
pilot light is not lit up and
the oven is not heating up.
The oven door has not been
closed properly so it cannot
be locked automatically.
Check the door and make
sure that it is closed properly.
I have turned the control dial
to position , pressed the
key, I can see the P1, P2
or P3 on the display but the
pilot light is not lit up and
the oven is not heating up.
The door switch is not working
even though the door is
properly closed.
Call Technical Assistance
Service as there is a fault in
the door switch.

29
ENGLISH
INCIDENT CAUSE SOLUTION
I have programmed the
pyrolysis function, the oven is
working properly but pilot light
is not lit up.
Pilot light does not work
properly.
Call the Technical Assistance
Service.
The pyrolysis programme has
ended and the oven is cold,
but the door is locked and
symbol is flashing.
You did not turn the control
dial to position 0when the
pyrolysis programme ended.
1. Turn the control dial to
position 0and wait for 1
minute.
2. Turn the control dial to
position and wait for 1
minute.
3. Turn the control dial to
position 0again and wait
until pilot light turns off.
The control dial is in position
0and the door is still locked.
The oven has not cooled down
to the safe temperature.
Wait until the oven cools and
pilot light turns off.
The control dial is in position
0, the oven is cold and the
door is still locked.
You have not followed the
instructions to cancel the
operation correctly.
1. Turn the control dial to
position 0and wait for 1
minute.
2. Turn the control dial to
position and wait for 1
minute.
3. Turn the control dial to
position 0again and wait
until pilot light turns
off.
I have put the control dial in
position 0and the door is
unlocked, however symbol
is still lit up and the remaining
time of the cleaning cycle can
be seen on the
display.
You have not followed the
instructions to cancel the
operation correctly.
Follow the instructions to
cancel the pyrolysis
programme.