KWIK GOAL PRO PREMIER 2B9006 User manual

ASSEMBLY INSTRUCTIONS FOR 2B9006 & 2B9006SW PRO PREMIER COPA GOAL
NOTE: Components may be packaged in one or more additional boxes.
2. Read through entire instruction before beginning assembly and installation.
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has
occurred, notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging
immediately. Wet or damp packaging may damage contents.
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2016, Rev. 2019 Kwik Goal Ltd.
Right Post (1)
(Part# UZ649)
Left Post (1)
(Part# UZ1527)
Parts
NZ391 Rev. 07/15/19
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
®
280”
Crossbar (2)
(Part# UZ393)
280”
Back Bottom Bar (1)
(Part# UZ966) 100-3/8” 100-3/8”

140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
1998 rev 2009 Kwik Goal Ltd.
2. Safety/Warning labels must be clearly visible.
IMPORTANT GOAL SAFETY INSTRUCTIONS
READ CAREFULLY
1. Check for structural integrity and proper connecting hardware before every
use. Replace damaged or missing parts or fasteners immediately.
3. Securely anchor moveable soccer goals at ALL times.
4. Always instruct players, managers, coaches, trainers, teachers, maintenance
workers and all other personnel who might come in contact with the goal,
on the safe handling of and potential dangers associated with moveable
soccer goals.
5. Always exercise extreme caution when moving goals and provide adequate
manpower to move goals of varied sizes and weights. Moveable soccer goals
should only be moved by authorized personnel.
6. NEVER allow anyone to climb on the net or goal framework.
7. Moveable soccer goals should only be used on LEVEL fields, NEVER on a
slope or hill area.
8. Remove nets when goals are not in use.
9. Most of the tip-over injuries occurred when goals were unattended. Anchor
or chain one goal to another or to nearby fence posts, dugouts, or any other
similar sturdy fixture when not in use. If this is not practical, store moveable
soccer goals in a place where children cannot have access to them.
10. Fully disassemble goals for seasonal storage.
NZ391 Rev. 07/15/19

Chain (4)
w/ Snap Link & Anchor Plate
(Part# UZ846 )
Back Pole Brace (2)
(Part# UZ1526)
Back Pole Brace (2)
(Part# UZ1525)
Post Brace (2)
(Part# UZ737)
Anchor Bag (6)
(Part# 10B1605)
Ground Anchor (4)
w/hardware
(Part# 10B101 Set of 4)
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19
Back Pole (2)
(Part# UZ1524)
Net (1)
(Part# 3B1502)
Red Dot Blue Dot
Back Bottom Bar
Connector (2)
(Part# UZ1033)
Back Pole Cap (2)
(Part # VZ719)
Tamper Resistant
Net Clip (100)
(Part# 10B3401 Pack of 100)
Net Clip Driver (1)
(Part# VZ140)
Left Base (1)
(Part# UZ1520)
100-3/8”
Right Base (1)
(Part# UZ1521)
100-3/8”
Channel Spacer (8)
(Part# UZ812)
Bolt Cap (4)
(Part# VZ751)

Net Rope
Assembly (2)
(Part# JZ215 Pack of 2
w/ Snaplink)
Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
NZ391 Rev. 07/15/19
7/16” Lock Nut (Part# TZ47) (4)
Hardware
Note: Hardware may be packaged separately
in one or more boxes. Open all packages
before beginning assembly.
7/16” X 6” Hex Bolt (Part# TZ380) (4)
7/16” Flat Washer (Part# TZ171) (8)
3/8“ x 1-3/4” Hex Bolt (Part# TZ227) (16)
3/8" x 7/8" Hex Bolt (Part# TZ249) (18)
3/8” x 5/8” Hex Bolt (Part# TZ383) (4)
5/16" X 1” Hex Bolt (Part# TZ121) (8)
5/16" Flat Washer (Part# TZ269) (8)
3/8“ Lock Washer (Part# TZ65) (36)
3/8“ Flat Washer (Part# TZ60) (40)
3/8" Square Nut (Part# TZ247) (22)
5/16" Lock Washer (Part# TZ122) (8)
1/4" X 2” Eye Bolt (Part# TZ381) (2)
1/4" Lock Nut (Part# TZ19) (2)
1/4"Flat Washer (Part# TZ361) (2)
Ratchet with
7/16” ,1/2”, 5/8”,
9/16” & 3/4”
Sockets
9/16
7/16”, 1/2”, 5/8”,
9/16” & 3/4”
Wrenches
Rubber Mallet
Assembly Tools
Knob w/o Threads (4)
(Part# VZ687)
280”
Pole Rope
Assembly (4)
(Part# JZ222 Pack of 4)
112”

4. Insert one square nut in each of the assembled posts.
3. Attach left post and right post to crossbar using channel spacers and 3/8” hex bolts. Note direction of decals
before fastening. Be sure connections are pressed firmly together before tightening hex bolts.
Left Post
Right Post
Crossbar
Decals
3/8” Square Nut
3/8” X 1-3/4” Hex Bolt
Channel Spacer
3/8” Flat Washer
Right Post
3/8” Lock Washer
Crossbar
Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
NZ391 Rev. 07/15/19

5. Attach base to crossbar and bottom back bar as shown.
Note direction of decals before fastening. Assemble all
hardware first, then go back and tighten each bolt. Be
sure connections are pressed firmly together before
tightening hex bolts.
6. Using a rubber mallet, install bolt caps on exposed threads of
7/16” X 6” hex bolts.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
Left Base
Back Bottom Bar Crossbar
Right Base
Decals
Channel Spacer
3/8” X 1-3/4” Hex Bolt
3/8” Lock Washer
3/8” Flat Washer
3/8” Square Nut
Left Base Crossbar
3/8” Square Nut
Bolt Cap
Bolt Cap
Rubber Mallet
NZ391 Rev. 07/15/19
Back Bottom Bar
7/16” X 6” Hex Bolt
Channel Spacer
Left Base
7/16” Flat Washer
7/16” Lock Nut
3/8” X 1-3/4” Hex Bolt
Back Bottom Bar
Back Bottom Bar Connector
3/8” Lock Washer
3/8” Flat Washer

***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19
Crossbar
Base
Base
Crossbar
Left Post
Right Post
7. Lift assembled posts and insert into assembled bases. Be sure connections are pressed firmly together before
tightening bolts. Be sure to tighten both bolts on each post brace.
Base
3/8” Square Nut
3/8" X 7/8"
Hex Bolt
Flat Washer
Lock Washer
Post Brace
Post
3/8" X 1-3/4"
Hex Bolt
3/8” Flat Washer
3/8” Lock Washer
Channel Spacer
3/8" X 1-3/4" Hex Bolt
3/8” Lock Washer
3/8” Flat Washer

8. If using swivel wheels (2B9006SW) - skip to step 10, for all other goals continue to step 9.
10B409), also include two threaded channel spacers from wheel option package in each base.
9. Insert two 3/8” square nuts into left base and right base. NOTE: If installing optional wheels (Part#
Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
NZ391 Rev. 07/15/19
Threaded Channel Spacer
(metal)
(for wheel option 10B409)
3/8” Square Nuts
Base

***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
10. Assemble back poles as shown. Make sure eyebolt is in slot before tightening. Do not overtighten.
NZ391 Rev. 07/15/19
1/4” X 2” Eyebolt
Back Pole
Cap
3/8” Square Nuts
1/4” Flat Washer
1/4” Lock Nut
Slot
3/8” X 5/8” Hex Bolt
Knob
3/8” Flat Washer
3/8” Square Nut
before installing in back pole.
TIP: Use square nut to draw hex bolt into knob

Tamper Resistant Net Clip
(2 Per Back Pole)
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
7 FT
Pole Ropes
Net Clip
Driver
Tamper Resistant Net Clip
Pole Rope Assemblies
Loops Around Knobs
Tamper Resistant Net Clip
7 FT
Knobs
11. Put loop end of pole ropes (2) through eyebolt and place rope in channel. With rope assemblies placed in
channel, insert tamper resistant net clips at locations shown.
NZ391 Rev. 07/15/19
Knobs

Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
12. Attach back pole and braces to goal base. Use color dots on braces as a guide for brace location. Assemble all
hardware first, then go back and tighten each bolt. Do not overtighten.
Pole Brace
(red dot)
Pole Brace
(blue dot)
3/8” Lock Washer
3/8” Flat Washer
3/8” X 7/8” Hex Bolt
Back Pole
Pole Brace
(red dot)
5/16” Lock Washer
5/16” Flat Washer
5/16” X 1” Hex Bolt
Pole Brace
(blue dot)
Back Pole
3/8” Lock Washer
3/8” Flat Washer
3/8” X 7/8” Hex Bolt
NZ391 Rev. 07/15/19
3/8” Lock Washer
3/8” Flat Washer
3/8” X 7/8” Hex Bolt

***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19
13. To attach chain leashes insert two square nuts into each base. Attach chain leash at locations shown.
50"
3/8" Flat Washer
3/8" Lock Washer
3/8" x 7/8" Hex Bolt
Chain Leash
3/8" Square Nut
34"
3/8” Square Nuts
Base

Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
NZ391 Rev. 07/15/19
Stone
Concrete Concrete
Anchor Hole Detail
(4 places per goal)
20"
MIN
24" MIN
60°
Approx.
Field
Surface
Ground Anchor
12-3/4"
156"
34"
50"
Goal Line
312"
Ground Anchor locations
Centerline of Goal Line
14. Mark ground anchor hole locations. Prepare holes, install ground anchors and pour concrete.

***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
15. After concrete has fully cured, attach chain leashes to ground anchors. Be sure to apply a liberal amount of
anti-seize on bolt threads before installing into anchors. With goal leashed to all four anchors, test in
accordance with step 16.
1/2" Flat
Washer
1/2" Hex Bolt Assembled
NZ391 Rev. 07/15/19

16. The ground anchor and chain leash system supplied is the recommended and the safest method of anchoring
your goal. However, counterbalance weight may be used as a temporary anchoring system. A minimum of
240 lbs. must be placed on the back bottom bar for the goal to be stabilized. Test anchoring in accordance
with step 17.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19
- Distribute total amount
of weight evenly between
each back corner.
- Always fasten weight to
goal with straps or hardware.

2. Verify goal is attached to anchors according to instruction.
Full safety precautions must be taken while performing test.
ANCHOR TEST
1. Clear all persons from a minimum 50 foot radius surrounding the goal.
3. Apply a horizontal pull force of 247 lbs. to the center of the crossbar for 60 - 70 seconds.
4. If goal overturns during application of force or does not return to an upright position after removing force, an
alternate anchoring system must be used
17. After installing, test as described below to verify effectiveness of anchor system. If applicable, allow concrete
to fully cure before testing.
Crossbar
247 lbs.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19

Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
CAUTION: GOALS MUST BE PROPERLY ANCHORED OR STORED AT ALL TIMES.
18. Attach net to goal frame with tamper resistant net clips using net clip driver as shown. Untie, remove, and
discard backdrop rope.
CAUTION: DO NOT ATTEMPT TO CLIMB ON GOAL WHILE ATTACHING NET.
19. From underside of net, push end of 1st net rope
assembly through top rear corner of net. Clip net
corner, pole rope assembly, and net rope assembly
together with a snap link. Repeat for opposite corner
of net, with opposite end of net rope assembly.
NZ391 Rev. 07/15/19
Net Perimeter
Rope
Net Clip Driver
Tamper
Resistant
Net Clip
Pole Rope
Assembly
Net Rope
Assembly
Net Top Back
Corner

20. From underside of net, push end of 2nd net rope assembly through the 18th mesh of the net. Clip net rope
assembly to 2nd pole rope assembly. Wrap 2nd net rope assembly around 1st net rope assembly
approximately 12 times at center of net. Do NOT weave rope through meshes of nets. Nets must be free to
slide on ropes. Push end of 2nd net rope assembly through 18th mesh from opposite corner. Clip 2nd net
rope assembly to remaining 2nd pole rope assembly.
Any modifications to this or any Kwik Goal product will void any and all warranties.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
2nd Net Rope
Assembly
18 mesh 18 mesh
26 mesh
Top View
2nd Net Rope
Assembly
1st Net Rope
Assembly
NZ391 Rev. 07/15/19
1st Net Rope
Assembly
1st Net Rope
Assembly
1st Net Rope
Assembly
2nd Net Rope
Assembly

21. Tension 1st net rope assembly to remove any slack in the net side walls, both vertically and horizontally. Loop
ends of 1st net rope assembly around top knobs and tighten knobs to hold tension in rope. Minimum tension
required for a good appearance is recommended. Knobs should be locked in place at approximately the same
height on left and right poles.
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties. NZ391 Rev. 07/15/19
Knob
1st Net Rope
Assembly Pull
2nd Net Rope
Assembly
22. Remove sag in the net by tensioning 2nd net rope assembly. Loop
the ends of 2nd net rope assembly around bottom knob in left and
right poles. Minimum tension required for a good appearance is
recommended. Knobs should be locked in place at approximately the
same height on left and right poles.
1st Net Rope
Assembly
2nd Net Rope
Assembly
Go to kwikgoal.com for additional product information.

ASSEMBLY INSTRUCTIONS FOR SWIVEL WHEELS
2. Read through entire instruction before beginning assembly and installation.
1. Unpack all parts and check for damage that may have occurred during shipping. If damage has occurred,
notify Kwik Goal immediately. Lay out all parts. Remove all cardboard and packaging immediately. Wet or
damp packaging may damage contents.
NZ346 Rev. 07/24/17
140 Pacific Drive Quakertown, PA 18951
(P) 215-536-2200 / (P) 800-531-4252 / (F) 215-536-4309 / (F) 800-778-8869
Visit our website @ kwikgoal.com
2013 Rev. 2017 Kwik Goal Ltd.
(A)”
Rubber Pad (8)
(Part# VZ654)
Hairpin Cotter (4)
(Part# TZ351)
Swivel Wheel (4)
(Part# VZ629)
Cable Lanyard (4)
(Part# VZ653)
12”
Parts
***CAUTION***
This goal has been designed to be used for the game of soccer only. Goal posts must be anchored AT ALL TIMES
and shall be secured against overturning. Do not climb on the net or goal framework at any time! All fastenings
must be checked to insure they are fully tightened before and after each use of this product. Goal posts not in use
must be disassembled and properly stored in a safe, secure area (See included Guidelines for Moveable Soccer Goal
Safety.). Assembled goal posts should not be left unattended. Remove nets when goals are not in use. Do not use
this equipment during the threat of high winds. Goal posts should be checked for safety before and after each use.
All warning and safety labels included with this product must be visible at all times.
Any modifications to this or any Kwik Goal product will void any and all warranties.
Swivel Wheel Mounting Bracket (4)
(Part# UZ1356)
Mounting Bracket Pin (4)
Part# Dim (A) Goal Model Number
TZ348 5-5/8” 2B2001SW 2B3806SW 2B9006SW 2B9004SW
TZ347 3-5/16” 2B3306SW 2B3406SW 2B3706SW -
TZ378 4-3/16” 2B3006SW - - -