Kyla KSEN-231 Instructions for use

Thank you for using Kyla product! Please keep this Easy Start Guide for future
use. For support or help, visit kylaconnect.com
DISCLAIMER
Aztech Technologies Pte Ltd, its holding company and its associated
companies (hereinafter referred to collectively as “Aztech”) does not
guarantee that adequate warning or protection will be given, and disclaims
all warranties and representations, whether expressed, implied or otherwise
statutory, concerning the product, including without limitation any warranty
of merchantability or fitness for a particular purpose. Aztech shall not be liable
in any event for any consequential, indirect, incidental, special, exemplary,
punitive or enhanced damages resulting from the use, maintenance or
operation of the product.
The manufacturer makes no warranty or representation that the product
constitutes a fire alarm system or is compliant with any requirements
prescribed by any applicable state or laws, codes, regulations and/or other
specifications that may be set out by relevant authorities having jurisdiction
(collectively referred to as “regulations”). You shall be solely responsible for
compliance with all regulations.
To the maximum extent permitted by applicable law, you agree to hold
harmless and indemnify, including legal fees, the manufacturer and their
personnel against any third party claims or fines by authorities that arise
or are alleged to have arisen as a result of negligent or intentional act or
omission by you or breach by you of any the terms herein or any violation of
any regulations.
PACKAGE CONTENTS
PRODUCT DESCRIPTION
The Kyla HFAD Smoke Sensor is a stand-
alone smoke sensor with an in-built 3.0V
Lithium battery that can last for 10 years. It
utilizes a photoelectric sensor that allows
it to be more sensitive to detecting slow
smoldering fires which generates thick
black smokeand little heat.
Button
123
© 2022 Aztech Technologies Pte Ltd. All rights reserved.
PLACEMENT TIPS
NOTE
• Smokesensor should be installed on ceiling along an escape route
(e.g living room, corridor, dining room, staricase landing)
• To prevent false alarm, avoid installing in kitchens and bathrooms.
• For multi-storey homes, minimum 1 smoke sensor per storey is
recommended.
• Remove “silicon protection cover” before use.
Smoke Sensor
Location
HFAD Smoke Sensor x1 Plastic Anchor x2
Mounting Bracket x1 Screw x2
Power button
Hush button
(Gray Area)
Smart Smoke Sensor ESG_Amen.indd 1 22/06/2022 14:46:43
BUTTON
ACTION REMARKS
Press Power button and hush button at the
same time (red LED flash rapidly with alarm) Test Mode
Red LED flash every 10 seconds (9min-exit) Hush Button

INSTALLATION GUIDE
Ceiling mount with screw.
LED STATUS INDICATOR
NOTE
ACTION REMARKS
Red LED flash rapidly with alarm Smoke Warning
Red LED flashed once every 43 seconds and
alarm once Low Battery Warning
Green LED flash 3 times every 43 seconds Hysteresis Mode
456
EASY START GUIDE
SMOKE SENSOR HFAD
TECHNICAL SPECIFICATIONS
Model KSEN-231
Power supply One 3.0V Lithium battery
(non-replaceable)
Alarm current <=100 mA
Sound Level >=85 dB(A) at 3 meters
Smoke Sensor Photoelectric Sensor
Dimension ø56.6mm x H50.5mm
Operating Temperature 0 to 45°C
Non-Operating Temperature -25 to 70°C
Operating Humidity 0% to 95% Relative Humidity
(non-condensing)
Non-Operating Humidity 0% to 95%
Regulatory Compliance EN 14604:2005
1
3
2
4
Press the hush button for 0.5sec, red LED will
flash rapidly with alarm.
(If LED does not flash, please remove the main
unit and attach to the wall mount bracket
again)
Rotate clockwise 20º.
Plastic
Anchor
Alignment
marks
Smart Smoke Sensor ESG_Amen.indd 2 22/06/2022 14:46:44
•
There are no active visible or audible indications which can be intrusive
to
the householder. To confirm that the alarm is opertional, perform a
weekly button test.
•
Should the device fail to operate correctly, please contact us
•
Should the device indicate a battery fault warning, replace the smoke
alarm.
Note: If LED does not flash, please remove the main unit and attach to the wall mount bracket again’. This
needs to be ‘ceiling mount bracket