Kyocera copier User manual

Please read the Operation Guide before using the copier
Keep it close to the copier for easy reference
1500

All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying, recording or by any information storage and retrieval system,
without permission in writing from the Publisher.
Legal Restriction On Copying
• It may be prohibited to copy copyrighted material without permission of the copyright owner.
• It is prohibited under any circumstances to copy domestic or foreign currencies.
• Copying other items may be prohibited.

i
The explanations contained in this operation guide have been
separated into different sections in order to allow even those using
a copier for the first time to use this machine efficiently, properly
and with relative ease.
A basic introduction to each section can be found below for
reference. Refer to the related section when using this copier.
Section 1 IMPORTANT! PLEASE READ FIRST.
This section contains explanations on information that is necessary
for you to know prior to using this copier for the first time after
purchase.
For example, it contains notes and cautions on installation and
operation that should be strictly obeyed in order to ensure its safe
and proper operation.
Section 2 NAMES OF PARTS
This section contains explanations on the names and functions of
the parts of the copier and its operation panel.
Section 3 PREPARATIONS
This section contains explanations on loading copy paper and
attaching the face-up tray.
Section 4 BASIC OPERATION
This section contains explanations on the basic procedures
required to make simple copies.
Section 5 COPY FUNCTIONS
This section contains explanations on using the various convenient
functions of this copier.
Section 6 COPY DEFAULT SETTINGS
This section contains explanations on changing the various default
settings available for adjusting the copier to fit your copy needs.
Section 7 OPTIONAL EQUIPMENT
This section contains explanations on the optional equipment that
are available for use with this copier.
Section 8 TROUBLESHOOTING
This section contains explanations on handling problems that may
occur during operation of this copier, such as when an error
indication appears or if a paper jam occurs.
Section 9 MAINTENANCE AND OPERATION
INFORMATION
This section contains explanations on maintaining the copier in
proper condition and on replacing the toner container, as well as
information on the specifications for this copier.
This Operation Guide contains certain symbols to indicate points of
caution and additional information that is important for you to
know.
The symbols and their meanings are indicated below.
IMPORTANT!
This symbol indicates information on procedures that should or
should not be performed in order to avoid trouble.
NOTE(S)
This symbol indicates information on additional explanations or
procedures for your reference.
Introduction to this Operation Guide Symbols in this guide

ii
CONTENTS
Energy Star Program .......................................................................iv
Please read this Operation Guide before using the copier. Keep it
close to the copier for easy reference. ...............................................v
Section 1
IMPORTANT! PLEASE READ FIRST. 1-1
CAUTION LABELS .......................................................................1-1
INSTALLATION PRECAUTIONS ................................................1-2
PRECAUTIONS FOR USE ............................................................1-3
Section 2
NAMES OF PARTS ..................................2-1
Main Body .......................................................................................2-1
Operation panel ..............................................................................2-4
Section 3
PREPARATIONS .....................................3-1
Loading paper .................................................................................3-1
Note when adding paper ..........................................................3-1
Loading paper into a drawer ...................................................3-1
Setting paper on the multi-bypass tray ..................................3-5
Thick Paper mode ....................................................................3-9
Attaching the face-up tray ...........................................................3-10
Section 4
BASIC OPERATION ................................4-1
Basic copying procedure .................................................................4-1
Making enlarged and reduced copies ............................................4-4
Zoom mode ................................................................................4-4
Preset Zoom mode ....................................................................4-5
Low Power mode ............................................................................4-6
Off mode ..........................................................................................4-7
Section 5
COPY FUNCTIONS .................................5-1
Layout modes .................................................................................5-1
2-in-1 .........................................................................................5-1
4-in-1 .........................................................................................5-5
Selecting the borderline ...........................................................5-6
Selecting the order of 4-in-1 layout .........................................5-7
Sort mode ........................................................................................5-9
Program function ..........................................................................5-10
Registering the program ........................................................5-10
Using programmed settings to make copies .........................5-10
Section 6
COPY DEFAULT SETTINGS .................6-1
Available default items ..................................................................6-1
Accessing and changing the default settings ................................6-6
Checking the total copy count and printing out a report ...........6-12
Section 7
OPTIONAL EQUIPMENT ...................... 7-1
Document Processor ................................................................7-1
Paper Feeder ............................................................................7-4
Additional Memory ..................................................................7-4
Section 8
TROUBLESHOOTING ............................ 8-1
If one of the following indications is displayed ............................8-1
If paper jams ..................................................................................8-3
Misfeed location indicators .....................................................8-3
Cautions ...................................................................................8-3
Removal procedures ................................................................8-4
If other trouble occurs ....................................................................8-9
Section 9
MAINTENANCE AND OPERATION
INFORMATION ....................................... 9-1
Cleaning the copier ........................................................................9-1
Replacing the toner container .......................................................9-2
Specifications ................................................................................. 9-6
Main Body ................................................................................9-6
Document Processor (option) ..................................................9-7
Paper Feeder (option) ..............................................................9-7
Additional Memory (option) ....................................................9-7
Environmental Specifications .......................................................9-8
Optional equipment .......................................................................9-9
Appendix: Functions and settings combination
chart ...................................................................... 9-10

iii
MAKING FULL USE OF THE COPIER’S ADVANCED FUNCTIONS
1Enlarging/reducing copies to a
desired size between 50% and 200%
<Zoom mode> (See page 4-4)
2Copying at a previously registered
magnification ratio
<Preset Zoom mode>
(See page 4-5)
3Making clear reproductions of
photographs
<Image quality selection>
(See page 4-1)
4Saving on toner use
<Eco-Copy mode> (See page 4-1)
5Making one copy from either two or
four originals
<Layout modes> (See page 5-1)
6Sorting automatically
<Sort mode> (See page 5-9)
7Memorizing frequently used
settings <Program function>
(See page 5-10)
8A full range of optional equipment is
available
• Document Processor (See page 7-1) • Paper Feeder (See page 7-4)
• Additional Memory (See page 7-4)
50%
200%

iv
Energy St ar Progra m
We have determined as a participating company in the
International Energy Star Program that this product is compliant
with the standards laid out in the International Energy Star
Program.
International Energy Star Program has as its basic goals the
promotion of efficient energy use and the reduction of the
environmental pollution that accompanies energy consumption by
promoting the manufacture and sale of products that fulfill
program standards.
International Energy Star Program standards require that copies
come equipped with a “Low Power Mode” where energy
consumption is reduced after a certain amount of time elapses
since the device was last used, as well as an “Off Mode” where the
device automatically turns itself off after there is no activity within
a set amount of time. When the copier includes printer and fax
functions, the printer and fax must enter a “Low Power Mode”
where power consumption is automatically reduced after a certain
amount of time elapses since they were last used, and they must
also support a “Sleep Mode” where power consumption is reduced
to a minimum when there is no activity within a set amount of
time.
This product is equipped with the following features as a result of
its compliance with International Energy Star Program standards.
Low Power Mode
The device automatically enters “Low Power Mode” when 15
minutes have passed since the device was last used. The amount of
time of no activity that must pass before “Low Power Mode” is
activated may be lengthened. See “Low Power mode” for more
information.
Off Mode
The device automatically enters “Off Mode” when 60 minutes have
passed since the device was last used. The amount of time of no
activity that must pass before “Off Mode” is activated may be
lengthened. For more information see “Off mode”.
Paper Recycling
The Energy Star Program encourages the use of environmentally
friendly recycled paper. Your sales or service representative can
provide information about recommended paper types.
About the International Energy Star Program

v
Please read this OperationGu ide before using the copier. Keep it close to the copier for easy reference.
Please read this Operation Guide before using the copier. Keep it close to the copier for easy
reference.
The sections of this guide and parts of the copier marked with symbols are safety warnings meant to
protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the
copier. The symbols and their meanings are indicated below.
Symbols
The symbol indicates that the related section includes safety warnings. Specific points of attention are
indicated inside the symbol.
The symbol indicates that the related section includes information on prohibited actions. Specifics of
the prohibited action are indicated inside the symbol.
The zsymbol indicates that the related section includes information on actions which must be
performed. Specifics of the required action are indicated inside the symbol.
Please contact your service representative to order a replacement if the safety warnings in this Operation
Guide are illegible or if the guide itself is missing. (fee required)
DANGER: Indicates that serious injury or even death will very possibly result from
insufficient attention to or incorrect compliance with the related points.
WARNING: Indicates that serious injury or even death may result from insufficient
attention to or incorrect compliance with the related points.
CAUTION: Indicates that personal injury or mechanical damage may result from
insufficient attention to or incorrect compliance with the related points.
..........[General warning]
..........[Warning of danger of electrical shock]
..........[Warning of high temperature]
..........[Warning of prohibited action]
..........[Disassembly prohibited]
..........[Alert of required action]
..........[Remove the power plug from the outlet]
..........[Always connect the copier to an outlet with a ground connection]

vi

1-1
Section 1 IMPORTANT! PLEASE READ
FIRST.
CAUTION LABELS
Caution labels have been attached to the copier at the following locations for safety purposes.
BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing
toner.
Label 1
High temperature inside.
Do not touch parts in this area,
because there is a danger of getting
burned. ..............................................
NOTE: DO NOT remove these labels.
Label 2
High temperature inside.
Do not touch parts in this area,
because there is a danger of getting
burned. ..............................................

1-2
INSTALLATION PRECAUTIONS
Environment
CAUTION
Avoid placing the copier on or in locations
which are unstable or not level. Such
locations may cause the copier to fall down or
fall over. This type of situation presents a
danger of personal injury or damage to the
copier. .............................................................................
Avoid locations with humidity or dust and
dirt. If dust or dirt become attached to the
power plug, clean the plug to avoid the
danger of fire or electrical shock. .......................
Avoid locations near radiators, heaters, or
other heat sources, or locations near
flammable items, to avoid the danger of fire.
To keep the copier cool and facilitate
changing of parts and maintenance, allow
access space as shown below. Leave adequate
space, especially around the vents, to allow
air to be properly ventilated out of the copier.
Other precautions
Adverse environmental conditions may affect the safe
operation and performance of the copier. Install in an
air-conditioned room (recommended room
temperature: around 68°F (20°C), humidity: around
65%) and avoid the following locations when selecting
a site for the copier.
• Avoid locations near a window or with exposure to
direct sunlight.
• Avoid locations with vibrations.
• Avoid locations with drastic temperature
fluctuations.
• Avoid locations with direct exposure to hot or cold
air.
• Avoid poorly ventilated locations.
During copying, some ozone is released, but the
amount does not cause any ill effect to one's health. If,
however, the copier is used over a long period of time
in a poorly ventilated room or when making an
extremely large number of copies, the smell may
become unpleasant. To maintain the appropriate
environment for copy work, it is suggested that the
room be properly ventilated.
Power supply/Grounding the copier
WARNING
DO NOT use a power supply with a voltage
other than that specified. Avoid multiple
connections in the same outlet. These types
of situations present a danger of fire or
electrical shock. .........................................................
Plug the power cord securely into the outlet.
If metallic objects come in contact with the
prongs on the plug, it may cause a fire or
electric shock. .............................................................
Always connect the copier to an outlet with a
ground connection to avoid the danger of fire
or electrical shock in case of an electric short.
If an earth connection is not possible, contact
your service representative. ................................
Other precautions
Connect the power plug to the closest outlet possible
to the copier.
The power supply cord is used as the main disconnect
device. Ensure that the socket/outlet is
located/installed near the equipment and is easily
accessible.
Handling of plastic bags
WARNING
Keep the plastic bags that are used with the
copier away from children. The plastic may
cling to their nose and mouth causing
suffocation. ..................................................................
Left:
11 13/16"
30 cm
Front:
39 3/8"
100 cm
Right:
11 13/16"
30 cm
Rear:
11 13/16"
30 cm

1-3
PRECAUTIONS FOR USE
Cautions when using the copier
WARNING
DO NOT place metallic objects or containers
with water (flower vases, flower pots, cups,
etc.) on or near the copier. This of situation
presents a danger of fire or electrical shock
should they fall inside. ..................................
DO NOT remove any of the covers from the
copier as there is a danger of electrical shock
from high voltage parts inside the copier. ....
DO NOT damage, break or attempt to repair
the power cord. DO NOT place heavy objects
on the cord, pull it, bend it unnecessarily or
cause any other type of damage.
These types of situations present a danger of
fire or electrical shock. ...................................
NEVER attempt to repair or disassemble the
copier or its parts as there is a danger of fire,
electrical shock or damage to the laser. If the
laser beam escapes, there is a danger of it
causing blindness............................................
If the copier becomes excessively hot, smoke
appears from the copier, there is an odd
smell, or any other abnormal situation
occurs, there is a danger of fire or electrical
shock. Turn the power switch OFF ({)
immediately, BE ABSOLUTELY CERTAIN
to remove the power plug from the outlet and
then contact your service representative. .....
If anything harmful (paper clips, water,
other fluids, etc.) falls into the copier, turn
the power switch OFF ({) immediately.
Next, BE ABSOLUTELY CERTAIN to
remove the power plug from the outlet to
avoid the danger of fire or electrical shock.
Then contact your service representative. ...
DO NOT remove or connect the power plug
with wet hands, as there is a danger of
electrical shock. ..............................................
ALWAYS contact your service representative
for maintenance or repair of internal parts.
CAUTION
DO NOT pull the power cord when removing
it from the outlet. If the power cord is pulled,
the wires may become broken and there is a
danger of fire or electrical shock. (ALWAYS
grasp the power plug when removing the
power cord from the outlet.) .........................
ALWAYS remove the power plug from the
outlet when moving the copier. If the power
cord is damaged, there is a danger of fire or
electrical shock. .............................................
If the copier will not be used for a short
period of time (overnight, etc.), turn the
power switch OFF ({).
If it will not be used for an extended period of
time (vacations, etc.), remove the power plug
from the outlet for safety purposes during
the time the copier is not in use. ..................
ALWAYS hold the designated parts only
when lifting or moving the copier. ................
For safety purposes, ALWAYS remove the
power plug from the outlet when performing
cleaning operations. .......................................
If dust accumulates within the copier, there
is a danger of fire or other trouble. It is
therefore recommended that you consult
with your service representative in regard to
cleaning of internal parts. This is
particularly effective if accomplished prior to
seasons of high humidity. Consult with your
service representative in regard to the cost of
cleaning the internal parts of the copier. .....

1-4
Other precautions
DO NOT place heavy objects on the copier or cause
other damage to the copier.
DO NOT open the upper front cover, turn off the
power switch, or pull out the power plug during
copying.
When lifting or moving the copier, contact your
service representative.
Do not touch electrical parts, such as connectors or
printed circuit boards. They could be damaged by
static electricity.
DO NOT attempt to perform any operations not
explained in this handbook.
CAUTION: Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Do not look directly at the light from the scanning
lamp as it may cause your eyes to feel tired or painful.
Cautions when handling
consumables
CAUTION
DO NOT attempt to incinerate the toner
container. Dangerous sparks may cause
burns. .............................................................
Keep the toner container out of the reach of
children. .........................................................
If toner happens to spill from the toner
container, avoid inhalation and ingestion, as
well as contact with your eyes and skin. ......
• If you do happen to inhale toner, move to a place
with fresh air and gargle thoroughly with a large
amount of water. If coughing develops, contact a
physician.
• If you do happen to ingest toner, rinse your mouth
out with water and drink 1 or 2 cups of water to
dilute the contents of your stomach. If necessary,
contact a physician.
• If you do happen to get toner in your eyes, flush
them thoroughly with water. If there is any
remaining tenderness, contact a physician.
• If toner does happen to get on your skin, wash with
soap and water.
DO NOT attempt to force open or destroy the
toner container. .............................................
Other precautions
After use, ALWAYS dispose of the toner container in
accordance with Federal, State and Local rules and
regulations.
Store all consumables in a cool, dark location.
If the copier will not be used for an extended period of
time, remove the paper from the drawer, return it to
its original package and reseal it.

1-5
SAFETY OF LASER BEAM
1. Safety of laser beam
This copier has been certified by the manufacturer to Class 1 level under the radiation performance standards
established by the U.S.DHHS (Department of Health and Human Services) in 1968. This indicates that the
product is safe to use during normal operation and maintenance. The laser optical system, enclosed in a protective
housing and sealed within the external covers, never permits the laser beam to escape.
2. The CDRH Act
A laser-product-related act was implemented on Aug. 2, 1976, by the Center for Devices and Radiological Health
(CDRH) of the U.S. Food and Drug Administration (FDA). This act prohibits the sale of laser products in the U.S.
without certification, and applies to laser products manufactured after Aug. 1, 1976. The label shown below
indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United
States. On this copier, the label is on the rear.
3. Optical unit
4. Maintenance
For safety of the service personnel, follow the maintenance instructions in the other section of this manual.
5. Safety switch
The power to the laser unit is cut off when the upper front cover is opened.
When checking the optical unit, avoid
direct exposure to the laser beam, which is
invisible.
Shown at left is the label located on the
cover of the optical unit.

1-6
CAUTION!
The power plug is the main isolation device! Other switches on the equipment are only functional switches and
are not suitable for isolating the equipment from the power source.
ATTENTION!
Le débranchement de la fiche secteur est le seul moyen de mettre l’appareil hors tension. Les interrupteurs sur
l’appareil ne sont que des interrupteurs de fonctionnement : ils ne mettent pas l’appareil hors tension.
WARNING
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED
OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

1-7
LIMITED WARRANTY FOR NEW COPIER MODEL 1500
1. Kyocera warrants the Customer’s new copier, and the new accessories installed with the
initial installation of the copier, against any defects in material and workmanship for a
period of one year, or 100,000 copies from date of installation by an Authorized Dealer,
whichever first occurs. In the event the copier or an accessory is found to be defective within
the warranty period, Kyocera’s only obligation and the Customer’s exclusive remedy shall be
replacement of any defective parts. It is understood that Kyocera shall have no obligation to
furnish labor.
2. This warranty is valid only as to the original retail purchaser (referred to as the “Customer”)
of a new copier in the United States of America.
3. In order to obtain performance of this warranty, the Customer must immediately notify the
Authorized Dealer from whom the product was purchased. If the Dealer is not able to
provide service, write to Kyocera at the address below for the name and address of the
Authorized Dealer in your area.
4. This warranty does not cover copiers or accessories: (a) which have become damaged due to
operator negligence, misuse, accidents, improper storage or unusual physical or electrical
stress, (b) which have used parts or supplies which are not genuine Kyocera brand parts or
supplies, (c) which have been serviced by a technician not employed by Kyocera or an
Authorized Dealer, or (d) which have had the serial number modified, altered, or removed.
5. This warranty does not cover Maintenance Kits or the components of Maintenance Kits,
which consist of the drum unit, the fixing unit, and the developing unit. Kyocera shall give
the Customer a separate warranty for these items.
6. This warranty gives the Customer specific legal rights. The Customer may also have other
rights, which vary from state to state. Neither the seller, nor any other person is authorized
to extend the time period, or expand this warranty on behalf of Kyocera.
7. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, AND KYOCERA SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY
SHALL NOT EXTEND TO, AND KYOCERA SHALL NOT BE LIABLE FOR, ANY
INCIDENTAL OR CONSEQUENTAL DAMAGES WHICH MAY ARISE OUT OF THE
USE, OR INABILITY TO USE, THE COPIER.
KYOCERA MITA AMERICA, INC.
225 Sand Road
Fairfield, New Jersey
07004-0008, USA

1-8

2-1
Section 2 NAMES OF PARTS
(1) Original cover
(Open/close this cover when you are setting the original on the
platen.)
(2) Platen
(Set originals here for copying. Be sure to lay originals
face-down and align them flush up against the left rear corner
of the platen.)
(3) Original size indicator plate
(Be sure to align originals flush up against this plate when
setting them on the platen.)
(4) Operation panel
(Perform copy operations here.)
(5) Upper front cover
(Open this cover when you need to replace the toner container
or if a paper jam occurs inside the copier.)
(6) Front cover
(Open this cover when you need to replace the toner container
or if a paper jam occurs inside the copier.)
(7) Process Unit
(Take this unit out when you need to replace the toner
container or if a paper jam occurs inside the copier.)
(8) Toner container
(9) Lock lever
(Operate this lever when you need to replace the toner
container.)
(10) Toner container release lever
(Operate this lever when you need to replace the toner
container.)
(11) Charger cleaner
(Slide this knob back and forth when you need to clean the
charger.)
Main Body
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) (10)(9)
(11)

Section 2 NAMES OF PARTS
2-2
(12) Drawer
(This drawer has a storage capacity of 250 sheets of standard
copy paper (80 g/m²).)
(13) Paper width guides
(Adjust these guides to fit the width of the paper that is to be
loaded in the drawer.)
(14) Paper stopper
(Adjust this stopper to fit the length of the paper that is to be
loaded in the drawer.)
(15) Stopper extension lock
(Use this lock when loading Folio or Oficio II size paper in the
drawer.)
(16) Copy storage table
(Finished copies can be ejected and stored on this table. The
copy storage table has a storage capacity of 150 sheets of
standard copy paper (80 g/m²).)
(17) Multi-bypass tray
(Set paper on this tray when copying onto small-size or special
paper.)
(18) Multi-bypass extension
(Pull out this extension when using the multi-bypass tray.)
(19) Insert guides
(Align these guides to fit the width of the paper that is to be
set on the multi-bypass tray.)
(12)
(13)
(14)
(15)
(16)
(13)
(17) (18)
(19) (19)

Section 2 NAMES OF PARTS
2-3
(20) Power switch
(Turn this switch ON ( | ) before copying.)
(21) Face-up tray
(Finished copies can be ejected and stored face-up on this tray.
The face-up tray should be used when copying onto thick
paper and other special paper. This tray has a storage
capacity of 30 sheets of standard copy paper (80 g/m²) but only
1 sheet of special paper should be stored there at one time.)
(22) Power cord
(23) Document Processor connector
(Attach the connection cable here when installing the optional
Document Processor.)
(24) Right cover anchor pin
(This pin must be removed and the right cover opened in order
to access the slot for installing additional memory. If you need
to add additional memory, contact your service representative
or an authorized service center.)
(20)
(21)
(22)
(23)
(24)
IMPORTANT!
• Be sure to hold both the front and rear sides of the copier when carrying it, as shown in the illustration.
• Be sure not to pull the drawer out when holding the front of the copier.
• Be sure that the original cover is closed whenever transporting the copier.
• DO NOT attempt to carry the copier by holding only the top portion. Doing so may result in you dropping the copier and thereby
damaging the copier and/or its covers.

Section 2 NAMES OF PARTS
2-4
(1) Start key & indicator
(Press this key when you want to start copying. Copying will
begin immediately if you press this key when the indicator is
lit green.)
(2) Reset/Power key
(Press this key when you want to cancel the currently entered
setting(s) and return to those registered for the initial mode.
Press down on this key for at least 3 seconds when you want to
engage the Off mode. When you want to release the copier
from the Off mode, press any one of the keys on the operation
panel. See page 2-5 for details on the initial mode and
page 4-7 for details on the Off mode.)
(3) Stop/Clear key
(Press this key when you want to stop copying. Press down on
this key for at least 3 seconds when you want to view the total
copy count. See page 6-12.)
(4) Copy quantity/magnification display
(Displays the number of copies to be made or the currently
selected magnification ratio. When the “%” symbol is lit, the
displayed number is the currently selected magnification
ratio.)
(5) Exposure adjustment keys
(Press the left key when you want to make the copy exposure
lighter and the right key to make the exposure darker. Press
down on both keys at the same time for at least 3 seconds
when you want to access the default settings mode.)
(6) Image quality select key
(Press this key when you want to select the desired image
quality mode. See page 4-1.)
(7) Number of Copies / Zoom(+) key
(Press this key when you want to raise the number of copies to
be made, as well as to increase the currently selected copy
magnification ratio. Press this key as well during default
settings in order to select the desired default item or setting.)
(8) Number of Copies / Zoom(-) key
(Press this key when you want to lower the number of copies
to be made, as well as to decrease the currently selected copy
magnification ratio. Press this key as well during default
settings in order to select the desired default item or setting.)
(9) Recall%/Enter key
(Press this key when you want copy in the Zoom mode. Press
this key as well during default settings in order to select the
current default item or register the currently displayed
setting. See page 4-4.)
(10) Reduce/Enlarge key
(Press this key when you want to use the Preset Zoom mode.
See page 4-5.)
(11) Paper Select key
(Press this key when you want to switch paper feed between
the drawer(s) and the multi-bypass tray. The indicator for the
currently selected source of paper feed will be lit green. Press
down on this key for at least 3 seconds when you want to
access the default items for paper size selection. See page 4-1.)
(12) Thick Paper key & indicator
(Press this key when you want to copy onto thick paper. Make
sure that the Thick Paper indicator is lit green. See page 3-9.)
(13) 2in1/4in1 key & indicators
(Press this key when you want to copy with the Layout modes.
Make sure that the 2in1 or the 4in1 indicator, as appropriate,
is lit green. Press down on this key for at least 3 seconds when
you want to access the default items for the Layout modes. See
page 5-1 for more information on the Layout modes.)
Operation panel
(1)
(2)
(3)
(14)
(15)
(10)(7)(9)(8)(11)(5)(6)
(13)
(16)
(4)(17)(12)
(24)
(23)
(19)
(21)
(22)
(18)
(20)