L2 Microwave BA00T60W15D-H User manual

BA00T60W15D-HBroadband System User Manual
1
Operating Manual
and Specification
Model
BA00T60W15D-H
L2Microwave Corp.

BA00T60W15D-HBroadband System User Manual
2
Table of Contents
1. General Description……………………………………………………………………………………..3
2. Operating Instructions…………………………………………………………………………….……4
3. Specifications……………………………………………………………………………………………….5
4. Maintenance………………………………………………………………………………………………..6
5. Test Report…………………………………………………………………………………………………..7

BA00T60W15D-HBroadband System User Manual
3
General Description
This model accumulated broadband technology has been applied for two bands
(Low Band: 0.02 GHz~1 GHz, High Band: 1 GHz~6 GHz) and It can be selected by
switch in front of the amp.
This model is provided high power and performance is suitable for testing.
Features
- Low/ High two bands operating
- 50 ohm input & output impedance
- Gain linearity
- Easy operation by one button
Applications
- Automated production test
- R&D Bench test
- RF component test
- RF burn-in
- Antenna power aging
- Broad band booster amplifier
Block Diagram

BA00T60W15D-HBroadband System User Manual
4
Operating Instructions
1. Signal Source output Connect to RF input port
2. RF output connect to DUT input or antenna port
-. RF OUT #1 : Low Band / 0.02~1 GHz Band
-. RF OUT #2 : High Band / 1~6 GHz Band
3. Select frequency band (Low/High)
4. Turn on the amplifier (Rear Power Button)
The input signal level should be maximum +3 dBm***
It should be connected the input & output connector
before turn on the amplifier
The Model needs about 2~3 min for warm-up time
Operator must read this manual before operate this model
***Please Refer appendix

BA00T60W15D-HBroadband System User Manual
5
Specifications
ELECTRICAL SPECIFICATIONS @ 220VAC, 25  C, 50 
Parameter
Min
Typ
Max
Unit
Operating Frequency
Band #1
20
1000
MHz
Band #2
1000
6000
MHz
Output Power @ PSAT, CW
Band #1
15
20
Watt
Band #2
15
18
Watt
Power Gain @ Psat
40
45
dB
Input Power for Rated PSAT
0
dBm
Gain Flatness @ Rated PSAT
Band #1
±1.5
dB
Band #2
±2.0
dB
Input Return Loss
-10
dB
In/Out Impedance
50
ohm
Third Order Intercept Point
+49
dBm
Harmonics @ Rated P1dB
-20
dBc
Spurious Signals
-70
-60
dBc
Power consumption @ PSAT
380
500
Watt
MECHANICAL SPECIFICATIONS
Parameter
Value
Units
Note
Dimensions ( H x W x D)
150 x 275 x 370 (TBD)
mm
Handy
Weight
(TBD)
kg
Max
RF Connectors Input/Output
N type, Female
Front
Primary Power
180~264 VAC, 50/60Hz
3 pin Single phase
Cooling
Air cooling
Self-contained fans & Heat sink
ENVIRONMENTAL CHARACTERISTICS (Design to Meet)
Parameter
Symbol
Min
Typ
Max
Unit
Operating Case Temperature
Tc
-20
+65
°C
Storage Temperature
Tstg
-40
+85
°C
Relative humidity (non-condensing)
RH
95
%

BA00T60W15D-HBroadband System User Manual
6
Maintenance
Components are conservatively operated to provide maximum instrument
reliability. In spite of this, parts within an instrument may fail. Usually, the
instrument must be immediately repaired with a minimum of “down time”.
A systematic approach can greatly simplify and thereby speed up the repair.
However, due to the importance of the amp’s alignment, it is recommended that
when failure is caused by breakdown of any of the components in the signal circuit,
the amplifier be returned to the factory for part replacement and amplifier
realignment.
Shipping address is as follows.
L2microwave Corp.
304-602, 345, Seokcheon-ro,
Bucheon-si, Gyeonggi-do, 14501,
Republic of Korea
Tel: [phone]
E-mail: [email protected]m

BA00T60W15D-HBroadband System User Manual
7
Test Report
ELECTRICAL SPECIFICATIONS @ +220VAC, 25C, 50Module
Parameter
Specifications
Test results (MHz)
Symbol
Min
Typ
Max
Units
Low
Center
High
Note
Operating Frequency
Band #1
BW
20
1000
MHz
20
500
1000
MHz
Band #2
1000
6000
1000
3000
6000
Output Power @ PSAT, CW
Band #1
PSAT
41.8
43
dBm
43.1
42.5
43
Plot 1
Band #2
41.8
42.5
43.1
42.8
42.8
Plot 2
Power Gain @ PSAT
Band #1
GSAT
40
45
dB
45.1
44.9
45
Plot 1
Band #2
44.1
43.8
43.8
Plot 2
Input Power for Rated PSAT
Band #1
PIN
0
dBm
-3
-5.5
-3
Band #2
-3
-3
-3
Gain Flatness @ Rated PSAT
Band #1
G
±1.5
dB
2.1
Plot 1
Band #2
±2.0
2.2
Plot 2
Input Return Loss
Band #1
S11
-10
dB
-26.0
-20
-18.6
Plot 1
Band #2
-17.7
-14.4
-10.3
Plot 2
3rd IMD 2-Tones
@ 34 dBm/Tone, 100 kHz
Spacing
Band #1
IM3 /
OIP3
-30 /
+49
dBc /
dBm
-35
/+55.5
-32
/+54
-29
/52.5
Record
/ cal.
Band #2
-31
/53.5
-27
/51.5
-24
/50
Harmonics @ P1dB
2nd /3rd
-20
dBc
-27 /-20
-28/-21
-31/-24
-20
-18/-34
-22/-31
-
Spurious Signals
Spurs
-70
-60
dBc
<-60
<-60
<-60
Performance Plots
Plots 1 –Low Band Small Signal and PSAT
Top Curve: Small Signal Gain @ PIN = -20 dBm
Middle Curve: Power Gain @ PSAT, PIN = -2.0 dBm
Reference: 44dB, 1dB/div.
Bottom Curve: Input Return Loss
Reference: 20dB, 10dB/div.
Plots 2 –High Band Small Signal and PSAT
Top Curve: Small Signal Gain @ PIN = -20 dBm
Middle Curve: Power Gain @ PSAT, PIN = -1.0 dBm
Reference: 47dB, 2dB/div.
Bottom Curve: Input Return Loss
Reference: 20dB, 10dB/div.