Labokey 7200 User manual

 Becarefulnottotouchfront/rearbladewhenchangingthebladesoastoavoidunexpectedaccident.
N.B.ScrewDriverwithmagnetisrecommendable,enablingeasyoperationtosecurescrews
whenattachingthebladeunit.
１．Howtochangefront/rearbladeofLABOKEY7200
1-1HowtodetachtheBladeUnitCover
Removescrews(3pcs)anddetachtheBladeUnitCoverasillustratedbelow.
FixingScrews(3pcs)BladeUnitCover
1-2 HowtodetachtheFixingScrewsofBladeUnit
Youcanseethefixingscrews(2pcs)fromthetop(asshownontheleftpicture)
SlightlypushdowntheLeveranddetachthescrews(2pcs)ofBladeUnitwhilegentlyfittingtheBlade
UnitwiththeBladeReceptacleBoardoftheFilmGuideSection(asshownontherightpicture)
BladeUnitwillbefitintotheFilmGuideSection.
Lever
FixingScrews(2pcs)ofBladeUnit BladeUnit FilmGuideSection
1-3 HowtodetachFilmGuideSectionandBladeUnit
DetachtheBottomCoverandremovefixingscrews(4pcs)ofFilmGuideSection(asshownontheleft
picture),thenremovetheFilmGuideSectionandtheBladeUnit.
FixingScrews(4pcs)ofFilmGuideSection -1-
LABOKEY7200RESHAPER/HOWTOCHANGEBLADE

２．HowtochangetheFrontBladeUnit
2-1 PreparenewFrontBladeSet(L720FB1A)
toreplacewiththeoneremoved.
RemovedFrontBladeUnit
NewFrontBladeSet(L720FB1A)
2-2HowtochangetheBladeReceptaclePlate
Asshowninthebelowpicture,removeEntryGuide(2screws),FilmPressPlate(2screws)andBlade
ReceptaclePlate(1screw)
PullouttheBladeReceptaclePlatebyliftingituptowardstheback.
EntryGuide・FilmPressPlate・BladeRecep.Plate BladeReceptaclePlate
2-3HowtoassembleFilmGuideSection
N.B.1.AssembletotheFilmGuideSectionwithcare.Besureonthematchingpitchesofscrews.
Assembleitinthereversedorderofdetaching.
WhenattachingtheFilmPressPlate,adjusttheholesofBladeReceptaclePlateandFilmPressPlate.
AssembletheEntryGuidebyslidingitfromtheleftoftheFilmPressPlate.(Below,arrowmarked)
Afterassembling,checkwhetherornottheFilmPositioningPlungerwillreturntotheoriginalposition
bypushingtheFilmPositioningPlunger(click-stopped)andLockPin.
EntryGuide HolesofBladeReceptacle LockPin FilmPositioningPlunger
PlateandFilmPressPlate
-2-

2-4 HowtoassemblewiththeUnit
SlightlyinserttheFrontBladeUnitintotheFilmGuideSectionandset.
FixgentlytheFilmGuideSectionassembledwithFrontBladeUnitwithfixingscrews(4pcs)
Screws(4pcs)
Then,fixtheBladeUnitwithbladeunitfixingscrews(2pcs)bypushingtheLeverdown.
AfterfixingtheBladeUnit,fixtightlytheFilmGuideSectionwithfixingscrews(4pcs)
Screws(4pcs)
Afterassembling,fixthebottomoftheUnitandadjusttheFrontBladeSetbyliftingtheLever
upanddownseveraltimes.
Youmayfeeltightfirst,butwillbecomesmoothshortly.
３．HowtochangetheRearBladeUnit
3-1PreparenewRearBladeSet(L720RB2A)
toreplacewiththeoneremoved.
RemovedRearBladeUnit
NewRearBladeSet(L720RB2A)
-3-

3-2HowtochangetheBladeReceptaclePlate
Asshowninthebelowpicture,removeEntryGuide(2screws),FrontFixingPlate(2screws)and
FilmPressPlate(2screws)
EntryGuide・FrontFixingPlate・FilmPressPlate
Then,untightenscrews(4pcs)oftheFilmGuideSection(Below,left)
N.B.Donotattempttoremovethescrews,otherwisetheinnerspringsmaybeoff.
Removethefixingscrews(2pcs)oftheBladeReceptaclePlateandpulloutitbyliftinguptowards
theback.
Untighten4screws BladeReceptaclePlate
3-3 HowtoassembletheFilmGuideSection
N.B.1.AssembletotheFilmGuideSectionwithcare.Besureonthematchingpitchesofscrews.
Assembleitinthereversedorderofdetaching.
FixtheBladeReceptaclePlateandtighten4screwsoftheFilmGuideSection.
WhenattachingtheFilmPressPlate,adjusttheholesofBladeReceptaclePlateandFilmPressPlate.
BecarefultoattachtheFrontFixingPlatesoasnottooverridetheholeofBladeReceptaclePlate.
AssembletheEntryGuidebyslidingitfromtheleftoftheFilmPressPlate.(Belowright,arrowmarked)
Afterassembling,checkwhetherornottheFilmPositioningPlungerwillreturntotheoriginalposition
bypushingtheFilmPositioningPlunger(click-stopped)andLockPin.
HolesofBladeReceptacle EntryGuide FilmPositioningPlunger
Plate&FilmPressPlateHolesofBladeReceptacle LockPin
Plate(3pcs) -4-

3-4 HowtoassemblewiththeUnit
SlightlyinserttheRearBladeUnitintotheFilmGuideSectionandset.
N.B.Restassuredofthecombinationofpunchedblade(4pcs)andguidancepoles(2pcs)
FixgentlytheFilmGuideSectionassembledwithRearBladeUnitwithfixingscrews(4pcs)
Then,attachtheBladeUnitwithfixingscrews(2pcs)bypushingtheLeverdown.
Screws(4pcs)
FixtheFilmGuideSectionwithfixingscrews(4pcs)tightlywhilepushingtheLeverdown.
Afterassembling,fixthebottomoftheUnitandadjusttheRearBladeSetbyliftingtheLever
upanddownseveraltimes.
Youmayfeeltightfirst,butwillbecomesmoothshortly.
-5-