La Crosse Technology 616-146Av3 User manual

616-146Av3 http://www.lacrossetechnology.com/support/ Page | 1
Model: 616-146Av3
DC: 040317
Atomic Projection Alarm Clock
AAA
AAA
Power Adapter
USB
Charge
Port 1A
Time, Alarm with
Snooze
Indoor
Temperature +
Trends
Projection Arm
Rotates 180°
Moon Phase +
Calendar

616-146Av3 http://www.lacrossetechnology.com/support/ Page | 2
GET STARTED
1. Insert the 5.0 volt power cable into the wall outlet, then into the
back of the clock.
2. (Optional), Insert 2 AAA batteries (not included) into the back of the
projection clock. Observe the correct polarity (+ or -).
3. Set time, date, etc.
SET TIME AND DATE
1. Hold the SET/°F/°C button 3 seconds to enter time set mode.
2. Press and release the +/PROJ or -/TIME buttons to adjust values.
Hold for fast adjustment.
3. Press and release the SET/°F/°C button to confirm and move to the next
item.
Time and Date setting order:
1. WWVB (ON/OFF)
2. Time Zone
3. DST Daylight Saving Time (ON/OFF)
4. 12/24 Hour Time Format
5. Hour
6. Minutes
7. Year
8. Month
9. Date
Note: Day of the week sets automatically.
Press the SET/°F/°C button to exit, or wait 20 seconds without pressing
buttons to return to the normal time display.
FAHRENHEIT/CELSIUS
•Press and release the SET/°F/°C button to select Fahrenheit or Celsius
temperature display.
SET TIME ALARM
1. Hold the ALARM button 3 seconds to enter alarm time set mode.
2. Press and release the +/PROJ or -/TIME buttons to adjust values.
3. Press and release the ALARM button to confirm adjustments and move
to the next item.
Alarm Time setting order:
1. Hours
2. Minutes

616-146Av3 http://www.lacrossetechnology.com/support/ Page | 3
ACTIVATE / DEACTIVATE TIME ALARM
•Press and release the ALARM button once to view alarm time.
•Press and release the ALARM button again to activate the alarm.
Bell icon appears.
•Press and release the ALARM button again to deactivate the alarm.
The bell icon disappears.
SNOOZE (Silences alarm temporarily)
•Press and release the SNOOZE/LIGHT button to silence alarm for 9
minutes.
•Zz will show.
•When in snooze mode, press ALARM to stop alarm for one day.
Note: The alarm is crescendo sound. The alarm will sound for 2 minutes and
then shut off completely.
USB CHARGE PORT
Charge a smart phone, camera or other devices when the forecast station is
plugged into a power outlet with the included power adapter.
NOTE: This is a power-output charging port. It does not supply power to the
forecast station.
•Connect your external device’s USB charging cable (not included) to the
USB charging port.
•Charging times will vary.
•USB Power Output: 1A maximum current. Charge 1A devices or
devices that are self-regulating.
MOON PHASE
The moon phase is based on the year, month and date set (manually or by
the WWVB signal). These are the moon phases.
BACKLIGHT AND PROJECTION INTENSITY (TOGETHER)
Press and release the SNOOZE/LIGHT button to adjust the brightness of the
backlight and projection image (together):
•ON High intensity
•ON Low intensity
•OFF
Note: When theAdapter is NOT in use, the High/Low/On/Off features are not
available.
Alarm
Bell Icon

616-146Av3 http://www.lacrossetechnology.com/support/ Page | 4
PROJECTION (On/Off, rotate, projection mode)
Battery Power: Press and release the SNOOZE/LIGHT button to show the
projection for 10 seconds.
Note: Using Battery power, the projection and backlight will come on for 10
seconds when SNOOZE/LIGHT is pressed. Projection will not display
constantly when operating on battery power.
A/C Power Projection ON/OFF:Projection is displayed constantly unless
turned off.
•Hold the +/PROJ button for 3 seconds to turn off the projection.
•Press and release the +/PROJ button to turn on the projection.
Rotate Projection:
•Press and release the PROJECTION button to rotate the projection
image 90 degrees.
•Press and release the PROJECTION button again to rotate another 90
degrees.
Change Projection Modes: Hold, then release the PROJECTION button to
switch projection modes. Watch the projection image to view the changes.
•Time and Indoor Temperature: alternate every 5 seconds (default)
•Time
•Indoor Temperature
MANUAL WWVB RADIO-CONTROLLED TIME SEARCH
•Press and release the -/TIME button to start or stop a manual signal
search. WWVB Icon will flash
For information about WWVB visit:
http://bit.ly/AtomicTime
TEMPERATURE TREND INDICATORS
The temperature (2°F/1°C) trend indicators update every 30 minutes or less.
•Temperature has risen in the past 3 hours.
•Temperature has not changed in the past 3 hours.
•Temperature has fallen in the past 3 hours.
LOW BATTERY ICON
If the icon is displayed in Indoor Temperature section,
replace batteries in the projection clock.
Low
Battery
Icon
WWVB
Icon

616-146Av3 http://www.lacrossetechnology.com/support/ Page | 5
POSITION PROJECTION ALARM
•The projection alarm has a wide base to sit on a desk or table.
•Choose a location 6 feet or more from electronics such as cordless phones,
wireless gaming systems, televisions, microwaves, routers, baby monitors, etc.,
which can prevent signal reception.
•Position near an exterior wall that faces Ft. Collins Colorado for WWVB time
signal reception.
CARE AND MAINTENANCE
•Do not mix old and new batteries
•Do not mix Alkaline, Standard, Lithium or Rechargeable Batteries
•Always purchase the correct size and grade of battery suitable for intended use.
•Replace all batteries of a set at the same time.
•Clean the battery contacts and also those of the device prior to battery installation.
•Ensure the batteries are installed with correct polarity (+ and -).
•Remove batteries from equipment when it is not to be used for an extended time.
•Promptly remove expired batteries.
SPECIFICATIONS
Indoor:
Temperature Range:
+32°F to +122°F (0°C to 50°C)
Interval:
About every 30 seconds
USB Charging Port
USB Output: 1 Amp maximum current
Power:
Primary Power:
AC: HX09-0501500-AU 5-volt AC power adapter (included)
Optional/Battery Backup Optional 2-AAA, IEC, LR3 batteries
(not included)
Battery Life:
Projection Alarm
Battery Backup:
Battery life is over 24 months when using the AC
adapter for primary power
Dimensions:
Projection Alarm:
5.23” L x 1.96” W x 4.33” H (133 x 50 x 110 mm)
WARRANTY AND SUPPORT
La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of
purchase) on this product relating to manufacturing defects in materials &
workmanship.
Before returning a product, please contact our friendly customer support or visit our
online help:
Phone: [phone] Online: http://www.lacrossetechnology.com/support/
View full warranty details online at:
http://www.lacrossetechnology.com/support/?type=warranty

616-146Av3 http://www.lacrossetechnology.com/support/ Page | 6
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other antenna
or transmitter.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized changes or modifications to this equipment. Such changes or
modifications could void the user authority to operate the equipment.
All rights reserved. This manual may not be reproduced in any form, even in part, or
duplicated or processed using electronic, mechanical or chemical process without the
written permission of the publisher.
This booklet may contain errors or misprints. The information it contains is regularly
checked and corrections are included in subsequent editions. We disclaim any
responsibility for any technical error or printing error, or their consequences. All
trademarks and patents are recognized.
CANADA STATEMENT
This device complies with CNR Industry Canada license -exempt devices.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.