La Crosse Technology 328-1415 Installation guide

1 | Page
328-1415 FAQS
We are weather enthusiasts like you and know proper running equipment is important. These
FAQS provide valuable information on your station's setup, positioning, and troubleshooting.
We recommend Adobe Reader version 10 or greater available at: http://get.adobe.com/reader
CONTENTS
328-1415 FAQS.................................................................................................................................................................... 1
CONTENTS ......................................................................................................................................................................... 1
GENERAL INFORMATION.................................................................................................................................................. 2
HARDWARE: Sensors and Station..................................................................................................................................... 2
What are the power requirements for this station? ......................................................................................................... 3
SETUP AND MOUNTING ................................................................................................................................................... 3
Installing Wind Cups if Needed ......................................................................................................................................... 3
SETUP: How do I set up my station?................................................................................................................................. 3
MOUNTING: Where do I mount/position my sensors?.................................................................................................... 4
Where do I place my station? ............................................................................................................................................ 6
How do I clean my Cyclone sensor? ................................................................................................................................ 6
What is Distance | Resistance | Interference? .................................................................................................................. 7
Wind Speed, Direction, Rain .............................................................................................................................................. 8
How do I interpret the Current Wind Readings?.............................................................................................................. 8
Help me understand the Wind History Readings............................................................................................................. 8
How do I reset the Wind History Readings? .................................................................................................................... 9
How Often does my Wind Sensor Update? ..................................................................................................................... 9
How do I read the Wind Direction?................................................................................................................................... 9
How do I view my Rain Readings? .................................................................................................................................... 9
How do I Reset Rain Readings? ...................................................................................................................................... 10
What are the Days Since THE LAST Rain? ..................................................................................................................... 10
How Often does my Rain Sensor Update? .................................................................................................................... 11
What does the Rain Cylinder Graph show?.................................................................................................................... 11
Temperature & Humidity .................................................................................................................................................. 11
How do I view my HI and LO Temperature/Humidity Readings?................................................................................. 11
How do I reset the Temperature/Humidity Readings?.................................................................................................. 12
What is Feels Like and Dew Point Temperature?.......................................................................................................... 12

2 | Page
Can I turn the Temperature Decimal Off or On?............................................................................................................ 12
Does this station have Alerts? ......................................................................................................................................... 13
TROUBLESHOOTING the Sensors ................................................................................................................................. 14
What does a reading of “HI” or “LO” mean? .................................................................................................................. 14
Why do I see “NO” for a sensor reading? ...................................................................................................................... 14
Why are my wind cups not spinning? ............................................................................................................................. 14
WIND READING 0.00: Why do I only see 0.00 for wind speed? ................................................................................. 15
Why do my Sensor readings come and go? .................................................................................................................. 15
WIND ACCURACY: Why is my wind speed inaccurate? ............................................................................................... 15
Why does my Rain Reading show “DAYS SINCE LAST RAIN” when it is raining?...................................................... 16
Rain Low: Why is my rainfall reading low?..................................................................................................................... 16
Rain High: Why is my Rainfall reading high? .................................................................................................................. 16
What can I do with my Rain Sensor in the winter?......................................................................................................... 17
Button Functions. .............................................................................................................................................................. 17
TIME: Does this station have Atomic Time? ................................................................................................................... 19
Explain the Daylight Saving Time settings...................................................................................................................... 19
How do I manually set the time? ..................................................................................................................................... 19
BACKLIGHT: Does this station have a backlight?.......................................................................................................... 21
What is Auto Dim?............................................................................................................................................................. 21
BATTERY: What do the battery icons mean? ................................................................................................................. 22
Does this station have 12-hour and 24-hour time options? .......................................................................................... 22
Why does the Moon Phase show when it is storming?................................................................................................. 22
Factory Reset: How do I factory reset my station? ........................................................................................................ 23
GENERAL INFORMATION
HARDWARE: SENSORS AND STATION
Your 328-1415 station comes with:
TX145WSDR (Cyclone) Sensor with Wind Speed, Wind Direction, and Rain
TX141TH-Bv4 Temperature/Humidity Sensor
Both sensors transmit at 433MHz.

3 | Page
WHAT ARE THE POWER REQUIREMENTS FOR THIS STATION?
TX145WSDR (Cyclone): 3 “AA” batteries
TX141TH-Bv4:2 “AA” batteries.
328-1415: 5-volt power cord (required) and CR2032 batteries for backup of your time and date.
Battery operation only will not update sensor or Wi-Fi data. A power cord is required.
SETUP AND MOUNTING
INSTALLING WIND CUPS IF NEEDED
Depending on how your station is packaged, you may need to install your Wind Cups onto your
Cyclone sensor.
SETUP: HOW DO I SET UP MY STATION?
Thermo-Hygro Sensor: Install 2 fresh “AA” batteries according to polarity and replace the
battery cover. The red LED light will flash when transmitting.
Cyclone Sensor: Install 3 fresh “AA” batteries according to polarity and replace the battery
cover.
2. Remove the Cyclone Sensor, Wind Cups, and Mini
Screwdriver from the package. Take note of the flat
edges located on the head of the Cyclone Sensor
and underside of the Wind Cups.
1. Align the flat edges and place the Wind Cups on top
of the Cyclone Sensor.
3. Carefully tighten the screw on the side of the cups
using the Mini Screwdriver. The screw should
tighten into the flat edge of the post.
4. When the screw is tight, gently pull up on the cups
to ensure they are secure. If they pull off, start
again with step two.

4 | Page
Weather Station: Insert the 5V Power Adapter into an outlet, and then plug it into the Power
Jack on the back of the station. Next, remove the Insulation Tab from the Station’s Battery
Compartment. About 30 seconds after powering the station on, it will automatically enter the
Settings Menu.
Note: It may take up to 10 minutes for the sensor data to appear on your station’s screen.
.MOUNTING: WHERE DO I MOUNT/POSITION MY SENSORS?
TX145WSDR (Cyclone):
•Use the built-in Bubble Level to ensure the Cyclone Sensor (especially the rain gauge) is
mounted level.
•Ensure the Solar Panel is facing the South. This helps optimize battery life and transmit
correct wind direction data.
•Ideally, the Cyclone Sensor should be mounted on the tallest object in your area. Avoid
positioning the sensor parallel or below eaves, roof lines, trees, or other objects that may
obstruct wind and rain readings.
•Make sure all the screws on the Mounting Bracket, Wind Cups, Wind Vane, and Battery
Compartment are securely fastened.
•The Cyclone Sensor should be mounted with the Wind Cups on the top.
•Place away from trees. Wind passing through trees moves slower than wind in open areas.
•The maximum transmission distance from your multi-sensor to your station, in the open air, is
330 feet (100 meters).
•Use the included mounting bracket or your mounting pole (no more than 1-inch outer
diameter to fit). Secure the sensor with the screws provided. Tighten the screws to snug (do
not over-tighten).
•Solar panel must face South to provide correct Wind Direction.
•General Wind Sensor mounting video: http://bit.ly/wind_sensor_mounting
Basic Mounting:
1. Mount the Mast to a flat surface with the four
provided screws. 2. Place the Cyclone Sensor on top of the Mast.
Ensure the Solar Panel is facing south.

5 | Page
Flexible Installation
Advanced Installation
Advanced installation options include tripods, wall mounts, chimney mounts, and many others.
Any of these can be combined with U-bolts for attachment onto a tall cylindrical conduit using
our Adjustable Base. These options will require additional equipment and professional help for
the best results.
4. Check the Bubble Level to ensure the sensor is
level.
3. Secure the Cyclone Sensor to the Mast by
tightening the screws on the side. Double check the
Bubble Level to be sure the sensor remains level.
2. Install the Hand Screw to the bracket, then Secure
the Cyclone Sensor to the Mast by tightening the
screws on the side.
1. This configuration allows you to attach the sensor
to angled locations and easily adjust ensure the
Mast and Sensor are level.
Freestanding Pole Setup
1'' Maximum Outside Pole Diameter
Tripod Setup Example
1'' Maximum Outside Pole Diameter

6 | Page
TX141TH-Bv4:
•Insert a mounting screw through the hole at the top to securely mount the sensor.
It can also hang from the back using a nail.
•Mount the sensor vertically in a protected well-shaded area. Keeping it out of direct
weather elements such as sunlight, rain, snow, etc. will help avoid inaccurate
readings.
•For additional protection against weather elements, a Sensor Weather Shield:
https://bit.ly/weather-shield can be purchased separately.
•The maximum wireless transmission range to the station is up to 330ft (100m) in open air. This
does not include walls, floors, or other large obstructions.
•For online video instruction visit: bit.ly/th_sensor_mounting.
WHERE DO I PLACE MY STATION?
Your station is designed for flexible placement on a desk or countertop, or to position on the
wall. When the stand is closed, it provides wall mounting holes.
•Position within reach of an outlet that is always active. Some of the outlets in living rooms
and bedrooms may only be active when the light switch is on.
•This station must operate with a 5-volt power cord for a constant backlight.
•The best sensor reception occurs when only one wall is between your station and each
sensor outside.
•Position your station six feet from other electronics and wireless devices. If you suspect RF
(radio frequency) interference, simply move your weather station a few feet in any direction.
•The Atomic Time Signal originates in Ft. Collins Colorado and has a range of 2000 miles. In
some cases, the signal is affected by weather conditions, geographic location. dwelling
construction materials or electrical interferences. The position of the station in the home may
result in poor reception. If the station has not synchronized to the correct time within a few
days of activation, you may need to move the station to a different location. It is best to
position the station near an exterior wall that faces toward Colorado.
HOW DO I CLEAN MY CYCLONE SENSOR?
Tip: To avoid erroneous rain readings while cleaning, you may choose to remove the batteries.
This will cause a loss of Wind and Rain readings during the cleaning process. After cleaning
insert the batteries again and hold the Wind, then the Rain buttons on your station to reconnect.
1. Remove the Rain Funnel by firmly twisting counterclockwise to unlock it. Then lift off.
2. Clear debris from the Rain Tipper inside the sensor. Clear any leaves, dirt, or insects that
may prevent the Rain Tipper from moving freely.
3. After cleaning, re-install the Rain Funnel. Place the Funnel into the sensor and twist
clockwise to attach.
4. Lock the Rain funnel in place. Ensure one of the Arrows on the Rain Funnel aligns with the
Lock Symbol located on the top of the sensor.

7 | Page
WHAT IS DISTANCE | RESISTANCE | INTERFERENCE?
Distance:
•The maximum transmitting range in the open air is over 330 feet (100 meters) between each
sensor and your station.
•Consider the signal path from your station to each sensor as a straight line.
•Consider the distance the station is from other electronics in the home.
Resistance:
•Each obstacle: walls, windows, vegetation, stucco, concrete, and large metal objects will
reduce the effective signal range by about one-half.
•Mounting your sensors on a metal fence can significantly reduce the effective signal range.
2. Remove the Rain Funnel by firmly twisting the
funnel counterclockwise and lifting.
1. Clear any leaves, insects, or other debris to allow
the Rain Tipper to rock freely. Check that the drain
vents on the bottom are clear.
4. After cleaning, re-install the Rain Funnel by placing
it back into the sensor and twisting clockwise until
secure.
3. You should feel the funnel lock into place when one
of the arrows lines up with the center of the
Lock/Unlock Line.

8 | Page
Interference:
•Consider electronics in the signal path between the sensors and your station.
•Simple relocation of the sensors or the station may correct an interference issue.
•Windows can reflect the radio signal.
•Metal will absorb the RF (radio frequency) signal.
•Stucco held to the wall by a metal mesh will cause interference.
•Transmitting antennas from ham radios, emergency dispatch centers, airports, military bases,
etc. may cause interference.
•Electrical wires, utilities, cables, etc. may create interference if too close.
WIND SPEED, DIRECTION, RAIN
HOW DO I INTERPRET THE CURRENT WIND READINGS?
Wind Speed Readings:
•WIND SPEED: 31 second highest wind speed. Within 31s cycle time, there are 10 sample data
(3s for each). The largest among these 10 samples will be sent as the current wind speed.
•Top (1 HR): Top Wind Speed in the past 60-minute period, from last record (10 minutes a
timestamp, total 6 records) (default record no timestamp).
Wind Direction:
•The Current and Prevailing Wind Direction are displayed in letters.
•In the settings section, you can choose the direction to display in degrees.
EX: NNE would read as 30°.
HELP ME UNDERSTAND THE WIND HISTORY READINGS.
1. Press and release the WIND button to view the maximum Wind Records values (Top Speed).
2. When viewing MONTH, use the PLUS button to toggle through the current month and the
past 11 months’ top speed.
Note: All other readings will disappear for 5 seconds.
•24-hour: Past 24-hour period, from last record Top speed in past 24 hours with time/date
stamp
•7 Days: Past 7-day period, from last record Top speed in past 7 days with time/date stamp
•Month: Top speed for a month with time/date stamp
oCurrent Month: First day to current day.
oPrevious 11 months. Defined by Calendar Month i.e., January 1 - January 31
•Year: Current Year. Defined by Calendar Year i.e., January 1 - December 31 Top speed for
the year with time/date stamp.

9 | Page
HOW DO I RESET THE WIND HISTORY READINGS?
Reset Wind Speed Records:
1. Press the WIND button to view individual wind speed readings.
2. Hold the MINUS button for five seconds to reset the individual value.
3. Wind speed reading will reset to the current wind speed, time, and date.
HOW OFTEN DOES MY WIND SENSOR UPDATE?
•Within 31s cycle time, there are 10 sample data (3s for each). The largest among these 10
samples will be sent as the current wind speed.
•Any change of 0.8km Wind Speed will cause the sensor to send the top speed for those 31
seconds.
•If there is no change in wind speed, the sensor will transmit every 3 minutes to preserve
battery life.
HOW DO I READ THE WIND DIRECTION?
Compass Rose:
•The Compass Rose displays the cardinal directions with visual indicators.
•The large diamond on the rose indicates the wind direction.
•The smaller triangles should be displayed next to the big triangle to create
more emphasis on the direction and let the user know that the direction
variates constantly.
Prevailing Wind Direction:
•The Prevailing Wind Direction reading will be the most common wind direction reading from
the past hour. This will be shown graphically inside the compass rose by one triangle that
will blink once every 3 seconds. It will be shown in letters or degrees in the lower right of the
wind area.
•If the prevailing wind direction arrow happens to fall in the same range as the current wind
speed arrows this is fine, it will just blink within the three current indicators.
Current Wind Direction: Updates about every 31 seconds. Found in the lower left side of the
wind area and can be read in letters or degrees.
HOW DO I VIEW MY RAIN READINGS?
1. Press and release the RAIN button to view different rain readings or auto-scroll through them
all. The Auto-scroll Icon will show when active and each rain reading will show for 5 seconds.
When Auto-scroll is off, press RAIN to cycle through all readings individually.

10 | Page
2. When viewing MONTH, use the PLUS button to toggle through the current month and past 11
months’ rainfall.
Note: All other readings will disappear for 5 seconds. Rainfall readings will stay on user
selection.
•1 HOUR: Last one-hour rainfall (12 consecutive 5 minutes rainfall accumulated total). Example:
current time is 6:49, 1HR rain is accumulated total between 5:50 and 6:49.
•24 HOURS: Based on the past 24 hours’ accumulated rain total. At each full hour, 1HR is
recorded. This is a running total.
•7 DAYS: Accumulated last 7 consecutive 24HR rain. On each day at 0:00, 24HR rain is
recorded. Not a subject to the calendar. Be sure the time is set.
•1 MONTH: Defined by Calendar Month i.e., January 1 - January 31
Example: January 1-January 31. On the first-month calendar day 0:00, the month of rain is
reset to 0. Accumulated rain from 1st of xx (month) to current day xx (month). The current
month will be shown in the date area.
•1 YEAR: Current month plus past 11 months total.
Example: current date is Nov. 10, 2023. Year rain is Jan 1, 2021 –Oct 31, 2022, month totals,
plus the current month (Nov 1-10) rain. The current Year will show in the time display.
•TOTAL: Total rainfall since powered on or reset.
Note: As time passes without rain, the 1-hour, 24-hour, and 7-day rain totals will count down to
zero. Example: Station recorded 0.4 inches of rain between noon and 1:00 pm on the previous
day.
•It continued to rain until the 24-hour rain reading from 11:00 am today, back to noon the
previous day was 1.2 inches.
•Then the 24-hour reading from noon today, back to 1:00 pm the previous day shows 0.8
inches. The 0.4 inches of rain from noon-1:00 pm on the previous day has dropped off the 24-
hour total.
HOW DO I RESET RAIN READINGS?
Reset Rainfall Readings (each reset individually):
•Press the RAIN button to view individual rain readings.
•Hold the MINUS button for five seconds to reset the individual value.
•Rainfall reading will reset to 0.00.
WHAT ARE THE DAYS SINCE THE LAST RAIN?
It does not rain every day in all locations. You may go days without rainfall. Your station is
designed to let you know when the last rain occurred.
•After 24 hours of no rainfall, the station will start counting days without rain. Rainfall readings
can be viewed by pressing the RAIN button.
•When rain starts it will automatically switch back to the last rainfall reading unit.

11 | Page
HOW OFTEN DOES MY RAIN SENSOR UPDATE?
The Rain signal is sent at the same time as the Wind signal.
•Your Rain Sensor checks for any change in rainfall every 31 seconds.
•Any change of 0.2mm of rain will cause the sensor to send a reading.
•If there is no change in rainfall, the sensor will transmit every 3 minutes to preserve battery
life.
WHAT DOES THE RAIN CYLINDER GRAPH SHOW?
The rain cylinder will have 10 segments that change with the rainfall total. The cylinder will show
two rain amount numbers next to the cylinder. These numbers will change with increased rainfall
amount.
•Each segment indicates 0.1 inch- up to 1 inch of rain. The graph will represent 1 inch. Over 1
inch the graph will represent 2 inches.
•Each segment indicates 0.4 inches- from 1 inch to 70 inches of rain. So, the graph will represent
2 inches at a time.
•The cylinder graph will read up to 70 inches of rain. Over 70 inches of rain, the graph will show
full.
•When in mm; Display 2 digits with decimal, or 3 digits (no decimal) at the halfway mark up to
999 mm.
•After 999 mm only show the top number on the graph when in mm.
TEMPERATURE & HUMIDITY
HOW DO I VIEW MY HI AND LO TEMPERATURE/HUMIDITY READINGS?
Your high and low temperature and humidity readings are recorded with time and date of
occurrence. Each time a new high or low reading is recorded, that reading with time and date of
occurrence will show. To view your HI | LO records, simply press and release the TEMP button.
Viewing order:
•Outdoor HI Temperature
•Outdoor LO Temperature
•Outdoor HI Humidity
•Outdoor LO Humidity
•Indoor HI Temperature
•Indoor LO Temperature
•Indoor HI Humidity
•Indoor LO Humidity

12 | Page
HOW DO I RESET THE TEMPERATURE/HUMIDITY READINGS?
Your temperature and humidity readings are reset individually.
1. Press and release the TEMP button to view the reading you wish to reset.
2. Hold the MINUS (-) button for 5 seconds to reset individual temperature or humidity value to
current temperature, humidity, time, and date.
3. Press and release the LIGHT button to exit.
WHAT IS FEELS LIKE AND DEW POINT TEMPERATURE?
Feels Like temperature indicates both Wind Chill and Heat index on stations with wind speed.
•Feels Like Temperature shows Wind Chill: When the temperature is below 50°F, and a 5
mph sustained wind speed, the Feels Like Temperature is showing Wind Chill.
•Feels Like temperature shows Heat Index: When the temperature is above 80°F, the Feels
Like temperature shows the Heat Index.
•Feels Like temperature shows Current Temperature: When the temperature is between
51°F and 80°F, the Feels Like temperature will remain the same as the outdoor temperature
regardless of humidity or wind speed.
Press and release the FEELS LIKE button to view:
•Feels Like HI
•Feels Like LO
•Dew Point
Note: Dew Point does not have a time/date of occurrence.
CAN I TURN THE TEMPERATURE DECIMAL OFF OR ON?
Press and release the DECIMAL ON/OFF button on the side of the station to turn the
temperature decimals ON or OFF. This can also be set within the station’s Settings Menu.

13 | Page
DOES THIS STATION HAVE ALERTS?
You may set Wind, Rain, Temperature, and Humidity alerts on your station.
•Alerts default to be OFF.
•The alerts menu is in the order listed below.
•When an alert is ON, the alert value flashes to be set. No additional button press is required.
•Leave an alert OFF (disarmed) press the ALERT button to skip setting that alert value.
•The HI or LO alert icon will show when the alert is active.
•When the armed alert value is reached, the station will beep five times each minute, until out
of alert range. The flashing Alert Value and Icon will indicate it is a LO or HI alert.
•Press any button to stop the alert sound. The alert icon will flash while the value is in the alert
range.
Alert Setting Order:
•High Wind Speed
•24 Hour Rainfall
•Outdoor HI Temperature
•Outdoor LO Temperature
•Outdoor HI Humidity
•Outdoor LO Humidity
•Indoor HI Temperature
•Indoor LO Temperature
•Indoor HI Humidity
•Indoor LO Humidity
Set Alerts:
1. Hold the ALERTS button to enter the Alert Settings Menu.
2. Use the +/- buttons to activate/deactivate individual alerts or press the ALERTS button to skip
to the next option.
3. Once activated, use the +/- buttons to adjust the values. Press the ALERTS button to confirm
and move forward.
Alert Triggered:
1. When the armed alert value is reached, the station will beep five times each minute, until out
of alert range. (1-second beep once, sound for 5 seconds, wait 55 seconds, and then repeat
begins to ring for 5 seconds.)
2. The flashing Alert Icon and Alert Value will indicate if it is a LO or HI alert.
3. Press any button to stop the alert sound. The alert icon will flash while the value is in the
alert range.

14 | Page
Deactivate Alerts:
Hold the ALERTS button to enter alert settings. Press and release the +/- buttons to deactivate
or activate alerts.
TROUBLESHOOTING THE SENSORS
WHAT DOES A READING OF “HI” OR “LO” MEAN?
•If your outdoor temperature reading shows “HI” or “LO,” check that your batteries are good.
•Overpowered or underpowered batteries can cause this reading.
•If the batteries are good, replace the outdoor sensor.
•If your temperature is fine but your humidity is reading “HI” or “LO” or dashes, your humidity
may be below 10% Relative Humidity. Your sensor does not read below 10% humidity.
WHY DO I SEE “NO” FOR A SENSOR READING?
•If a sensor loses connection to the station for any reason, the station will show NO after 30
minutes.
•The station will search for 3 minutes every hour to reconnect with the sensor.
•Hold the TEMP button for 2 seconds to search for the Outdoor Sensor
•Hold the WIND or RAIN button to search for the Cyclone Sensor
•Icon will flash while searching for the sensor. The sensor area will show dashes during the
search. When the sensor is received the icon will be solid.
•If no sensor is received, the icon would disappear after 3 minutes of searching if the sensor
is not found. NO will again show in the outdoor sensor area.
“NO” indicates the connection is lost between your station and the sensor.
•My first thought is always to check that my batteries are good. If it has been working and
now is not, low batteries are the most common connection problem.
•Next, check your distance, resistance, and interference. If everything was working previously
at the same location, this is not the issue. However, sometimes there is new growth on trees
or bushes that causes another barrier. Radio Frequency (RF) signal does not travel well
through foliage due to the moisture content.
•Occasionally adding a new wireless electronic device to the home will cross the signal path
for the sensor. If this occurs, try moving your station a few feet or turning the station 90
degrees for a better angle to receive the sensor signal.
WHY ARE MY WIND CUPS NOT SPINNING?
•Check for debris or ice preventing cups from moving.
•Check mounting location. Look for obstructions that prevent the wind from reaching the
sensor.

15 | Page
•In most cases, the wind sensor needs to be 4-6ft above the highest point on the roof to clear
nearby obstructions and read accurately.
•A 50-foot clearance in all directions is best.
•Push down firmly on the center of the cups to reseat them.
•Cups are replaceable.
WIND READING 0.00: WHY DO I ONLY SEE 0.00 FOR WIND SPEED?
The 0.00 means your wind sensor is connected to your station.
•Check that the cups spin freely. Something may be preventing movement.
•Are your wind cups unbroken? After a storm, it is good to check this.
WHY DO MY SENSOR READINGS COME AND GO?
•RF (radio frequency) communication may come and go occasionally. This can be normal in
some environments (e.g., moist climates).
•If a sensor goes out, please wait 2-4 hours for it to reconnect on its own. Please be patient –
these stations can reconnect, after many hours out.
•RF (radio frequency) communication is not always 100% on. Certain temporary conditions can
cause it to go out for a time (e.g., 100% humidity).
•Check that your sensor is receiving full sun on the solar panel.
If a miss happens:
•If your wind sensor loses connection to the station for any reason, the station will show
dashes after 30 minutes.
•The station will search for 5 minutes every hour to reconnect with the wind sensor.
Try this:
•Bring your wind sensor within ten feet of your station and make sure it is connected to the
station.
•After 15 minutes move the wind sensor into the next room with a wall between the sensor
and the station for 1 hour.
•If there is no loss of signal in that hour, move the wind sensor just outside.
•Continue moving the wind sensor back to its original location.
•If you lose connection, look for sources of interference.
WIND ACCURACY: WHY IS MY WIND SPEED INACCURATE?
•What are you comparing your wind speed to? Your local reporting station is miles from your
location and should not be used for comparison.
•Check the unit of measure (MPH, or KMH).
•Check to see if your station receives the same repetitive wind speed recording from the
sensor multiple times.
•Check that the cups turn freely.

16 | Page
•Check for obstructions that prevent clear wind flow to the cups.
•Check mounting. In most cases, the wind sensor needs to be six feet or more above the
highest point on the roof to clear nearby obstructions and read accurately. A 50-foot
clearance in all directions is best.
•It is helpful to send pictures of the sensor mounting if you need to contact customer support.
WHY DOES MY RAIN READING SHOW “DAYS SINCE LAST RAIN” WHEN
IT IS RAINING?
When new rainfall is counted your DAYS WITHOUT RAIN will immediately switch to the last
rainfall unit (1 hour, 24 hours, etc.) that you previously selected. If this does not happen, you have
lost connection to your Rain sensor.
Your Rain Sensor will show NO when it loses connection. 24 hours after it loses connection to
the station, you will see DAYS WITHOUT RAIN appear.
•Check that your Rain Sensor Reception Icon is present.
•If it is not Hold the Rain button to search for your rain sensor.
•Check that your Batteries are good and that, Distance, Resistance, and Interference are not
causing signal loss.
RAIN LOW: WHY IS MY RAINFALL READING LOW?
•Low rain readings indicate the rain sensor and station are connected.
•Check that the rocker tips freely.
•Check the funnel and the inside of the rain sensor for insect nests or debris that may cause
loss of rocker motion.
•Be sure to mount the rain sensor level.
Complete a Tip Test:
Write down the Total Rain reading or reset the Rain Total to 0.00. With the rain sensor mounted
slowly pour water into the funnel to tip the rocker of the rain sensor ten times. Wait at least 2
minutes for all the rain to collect. Repeat three times.
•Compare these tests. If they are the same, then your rain is reading correctly. If the rain
readings are different, repeat the test three times to avoid human error. Then look for causes
such as mounting too tight or debris clogging the funnel.
RAIN HIGH: WHY IS MY RAINFALL READING HIGH?
•Check for sources of RF (radio frequency) interference such as other wireless rain sensors,
ham radios, or electric transformers.
•Keep the station six feet from cordless phones or wireless routers etc.

17 | Page
Complete a Tip Test:
Write down the Total Rain reading or reset the Rain Total to 0.00. With the rain sensor mounted
slowly pour water into the funnel to tip the rocker of the rain sensor ten times. Wait at least 2
minutes for all the rain to collect. Repeat three times. Compare these tests. If they still read high
then contact support.
WHAT CAN I DO WITH MY RAIN SENSOR IN THE WINTER?
•Since your Rain sensor is connected to your Wind sensor, you do not need to do anything.
•It is self-emptying, and it is unlikely to freeze up.
•Your Rain sensor will not give an accurate account of snowfall. If you prefer not to have
melting snow count as rain, cover the Rain Funnel with plastic for the winter.
BUTTON FUNCTIONS.
There are 12 buttons on the station.
Top: ALERTS | WIND | TEMP | - (MINUS) | SET | + (PLUS) | ATOMIC | RAIN | LIGHT
Side: DECIMAL ON/OFF | HEAT/DEW
Back: RESET
1. ALERTS button
Normal Time Display-
•Hold to enter Alerts Settings
Alerts Mode-
•Press + or – to arm or disarm alert.
•Press and release ALERTS to move to the next setting
2. WIND button
Normal Display-
•Press and release to view top wind speed with time and date stamp.
•Hold to search for Cyclone sensor (Wind and Rain)
Wind Records Mode-
•Hold the - MINUS button for 5 seconds to delete individual wind Records readings.
3. TEMP button
Normal Time Display-
•Press to view HI/LO Records
•Hold to search for TH sensor from any source.
Temp Mode-
•Hold the MINUS button for 5 seconds to reset individual temp/humidity readings.

18 | Page
4. – (MINUS) Button:
Settings-
•Press to decrease values during setting.
•Hold 2 seconds to quickly adjust values.
Wind, Rain, Temp, History Mode-
•Hold 5 seconds to delete individual records.
Alerts Mode-
•Press to arm or disarm alert.
5. SET button:
Normal Time Display-
•Hold for 2 seconds to enter a setting mode for a time, date, etc.
Settings Mode-
•Press and release to move to the next item
6. + (PLUS) Button:
Setting Mode-
•Press to increase the values by one.
•Hold 2 seconds to quickly adjust values.
Alerts Mode-
•Press to arm or disarm alert.
7. ATOMIC Button:
Normal Time Display-
•Hold 2 seconds to search for Atomic Tome Signal
8. RAIN button
Normal Time Display-
•Press to view Rain History (24 hours, 1 hour, 7 days, Current Month, Current Year, Total) or
Pressure reading. The station can auto-scroll through all readings or stay on selection.
•Hold to search for Cyclone Sensor (Wind and Rain).
When Rain is displayed:
•Hold the MINUS button for 5 seconds to reset individual rain readings.
9. LIGHT button
Normal Time Display-
•Press to change the LCD backlight brightness (5 levels)
•Hold to set Auto Dim start/stop time.
Setting Modes-
•Press to exit any setting mode.

19 | Page
10. DECIMAL button
Normal Time Display-
•Press and release to turn Temperature Decimal ON or OFF.
11. FEELS LIKE button
Normal Time Display-
•Press to view Feels Like HI/LO Records and current Outdoor Dew Point.
12. RESET button
Normal Time Display-
•Hold 5 seconds to Restart Station to factory defaults.
TIME: DOES THIS STATION HAVE ATOMIC TIME?
•The station will only search for the atomic signal at UTC 7:00, 8:00, 9:00, 10:00, and 11:00.
•If there is no WWVB reception, the station will search for the atomic time signal every 2
hours until the WWVB time is received.
•The Atomic Time Signal Icon (Tower) will flash while searching. The tower icon will be solid
when it has connected.
•From the normal time display, press and release the ATOMIC button to manually search for
the WWVB time signal.
•The entire atomic icon will flash when searching.
EXPLAIN THE DAYLIGHT SAVING TIME SETTINGS.
AUTOMATIC DST: Changes Spring and Fall
ALL YEAR DST: Does not change to standard time in Fall.
NO DST: Does not change to DST in the Spring.
HOW DO I MANUALLY SET THE TIME?
1. Hold the SET button for 2 seconds to enter settings mode.
2. Press the + or - button to adjust the flashing values.
3. Hold the + or - button to adjust quickly.
4. Press the SET button to confirm adjustments and move to the next item.
5. Press the LIGHT button at any time to exit.
Settings Order:
•Greeting HELLO
•Language (English, Spanish, French, & German)
•Beep ON/OFF

20 | Page
•Atomic ON/OFF
•DST: Automatic, All Year, NO
•Time Zone
•12HR/24HR
•Hour
•Minute
•Year
•Month
•Date
•Month/Date or Date/Month
•Fahrenheit/Celsius
•Decimal ON/OFF
•Pressure Units INHG or HPA
•Pressure Number
•Rainfall Inches or Millimeters
•Wind Speed MPH or KMH
•Wind Direction Letters or Degrees
Settings Menu
1. On startup or if you hold the SET button for 2 seconds to enter setting mode. HELLO, will
show for two seconds, then automatically move to language. ENGLISH will show. Press the +
or - button to change to another language (Español, Français, or Deutsch). Press the SET
button to select Beep ON/OFF.
2. BEEP OFF will show. Press the MODE | + or – button to turn the beep sound OFF. Press the
SET button to move to 12/24 hour time.
3. ATOMIC ON will show. Press the MODE | + or – button to turn Atomic Time OFF. Press the
SET button to move to the DST selection.
4. AUTOMATIC DST will show. Press the MODE | + or – button to select ALL YEAR DST or NO
DST. Press the SET button to move to the Time Zone.
5. EASTERN will show. Press the MODE | + or – button to select a different Time Zone. Press
the SET button to move to 12/24 hour time.
6. 12/24 FORMAT will show. 12HR flashes. Press the + or - button to turn to select the 24-hour
time format.
7. Press SET to confirm and move to the hour. HOUR will show. The hour flashes. Press the +
or - button to choose the hour.
8. Press SET to confirm and move to the minutes. MINUTES will show. Minutes flash. Press the
+ or - button to choose the minutes.
9. Press SET to confirm and move to the year. The YEAR 2023 will show. The year will flash.
Press the + or - button to change the year.
10. Press SET to confirm and move to the month. The MONTH will show. The Month will flash.
Press the + or - button to change the month.
NOTE: When in 24 hour time format the
seconds will show in place of AM/PM.
TIME ZONES:
ATLANTIC
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII