La Crosse Technology WS-7034TWC User manual

WS-7034TWC
Wireless 433 MHz
Temperature Station
Instruction Manual

2
TABLE OF CONTENTS
Topic Page
Quick Setup 3-5
Inventory of Contents 6-7
Detailed Setup Guide
Battery Installation 8
Setting the Time 9-10
Selecting Units of
Measurement
10
Features
Minimum and Maximum
Temperatures
11
Resetting Minimum and
Maximum Temperatures
12
Adding additional remote
temperature sensors
(optional)
13-14
Mounting 15-16
Troubleshooting 17-18
Maintenance and Care 19
Specifications 20-21
Warranty Information 22-25

3
QUICK SETUP
Hint: Use good quality Alkaline
Batteries and avoid rechargeable
batteries.
1. Have the indoor temperature station
and remote temperature sensor 3 to
5 feet apart.
2. Batteries should be out of both
units for 10 minutes.
3. Place the batteries into the remote
temperature sensor first then into
the indoor temperature station.
(All remote temperature sensors must be
started before the indoor temperature
station)
4. DO NOT PRESS ANY BUTTONS
FOR 10 MINUTES.

4
In this time the indoor temperature
station and remote temperature sensor
will start to talk to each other and the
display will show both the indoor
temperature and an outdoor temperature.
If the indoor temperature station does
not display both temperatures after the
10 minutes please retry the set up as
stated above. After both indoor and
outdoor temperatures are displayed for
10 minutes you can place your remote
temperature sensor outdoors and set
your time.
The remote temperature sensor should
be placed in a dry, shaded area. The
remote temperature sensor has a range
of 80 feet. Any walls that the signal
will have to pass through will reduce
distance. An outdoor wall or window
will have 20 to 30 feet of resistance and
an interior wall will have 10 to 20 feet

5
of resistance. Your distance plus
resistance should not exceed 80 ft. in a
straight line.
NOTE: Fog and mist will not harm
your remote temperature sensor but
direct rain must be avoided.
To complete the set up of your indoor
temperature station after the 10 minutes
have passed please follow the steps on
pages 8-9.

INVENTORY OF CONTENTS
1. The indoor temperature station (Figure
1)
2. The remote temperature sensor (TX6U)
and mounting bracket. (Figure 2)
3. 3 each, 1/2” Philips screws.
4. One strip of double sided adhesive tape.
5. Instruction Manual and Warranty Card.
Figure 1
Holder
Figure 2
6

7
DDITIONAL EQUIPMENT
crewdriver.
batteries.
A
(not included)
1. 1 Philips s
2. 2 Fresh AAA Alkaline
3. 2 Fresh AA Alkaline batteries

8
Battery
DETAILED SETUP GUIDE
attery Installation
e
ure
cur.
2.
ure
ns
B
1. Install 2 AA
batteries in th
remote temperat
sensor. Make sure
they do not spring
free, or start-up
problems may oc
Install 2 AAA
batteries in the
indoor temperat
station. Do not
press any butto
for at least ten
minutes.
Cover

9
Setting the Time
ld the
2e the “MIN/MAX”
3“SET” button 2
4lease the “MIN/MAX”
5ET” button to
6/MAX”
7”button to
ote: When in 12h mode, there is only a
.”
1. Press and ho
“SET” button for 5
second, “12h” will
appear in the TIME
LCD.
. Press and releas
button to select either 12h time
(am/pm) or 24h time
. Press and release the
times, the hour will flash in the upper
left corner.
. Press and re
button to set the hours
. Press and release the “S
move to the minute setting
. Press and release the “MIN
button to set the minutes.
. Press and release the “SET
activate the clock.
N
“PM” display, which appears under “TIME

10
If there is no display here it is AM. Make
sure you set the time accordingly.
Selecting Units of Measurement
1. Press and hold the “SET” button for 5
second until “12h” or “24h” appears
in the TIME LCD.
2. Press and release the “SET” button
again, “°F” will appear in the TIME
LCD.
3. Press and release the “MIN/MAX”
button to shift between °F and °C.
4. Press and release the “SET” button
twice to activate settings.