La Scossa Elettrica Bee Meter Duo User manual

Bee Meter Duo
User Manual

2
Read this document before using the charger. Failure to follow any of the
instructions or warnings in this document can result in fire, electrical shock,
serious injury or death.
The charger is designed only for charging of electric vehicles that support IEC
62196-1 and IEC 61851-1. Do not use it for any other purpose or with any
other vehicle or object.
Do not use the charger if it is defective, fails to operate, appears cracked,
corroded, frayed, broken or otherwise seriously damaged, or LED indicates
serious internal error.
Ensure that the charging cable of the charger is not blocking the way for
pedestrians, other vehicles or objects.
Do not leave the charger in the hands of small children or incompetent people.
CAUTION!
!

3
*Max current and charging time depends on the characteristics of the electric vehicle being charged.
The EVSE can limit max current in extreme temperatures.
Max 3x32A* (22kW)
per socket
Less than 0.5W
-25°C to +55°C
Weather Resistant
52 x 36 x 26 cm
Type 1 or 2 in accordance to
IEC 62196-2 for 32A
Single Phase or Three Phase
IEC 62196, IEC 61851-1,
CE, EMC, RoHS
5m*
Technical Specifications
Rated charging current
Consumption in idle state
Allowed ambient temperature
Degree of protection
Dimensions (HxWxD)
Electric vehicle connector
Electric Power Supply
Constructed in accordance with
Cable length

4
Tools Required
Name
1Phillips screwdriver Electric (Bit preferred)
2Hex (M4) screwdriver Electric (Bit preferred)
3Level
4Stainless steel anchors X4 Size M10
5Stainless steel bolts X4 M10 to fit the anchors
6Drill When the anchors are not
pre-inserted.
732A Type B Circuit Breaker X2
8Type B 32A RCD X 2
9 N2XY 5X6mm Cable X 2 Length as needed
# Remarks

5
Prerequisites
Installation
This type of installation requires an electrical background.
When unpacking contents of the kit, it is crucial to
perform a visual check to confirm that none of the parts
are damaged/broken.
Prior to installation, make sure to disconnect the main
circuit breaker (CB).
Confirm that the charger’s serial number is configured in
NayaxVend under your local distributor/operator.
Make sure to always follow your local electrical regulations.
The Bee Meter installation should only be carried out by a
certified installer.
The below instructions are a guideline and provided for
reference only. You are solely responsible for following all
applicable electrical safety procedures, codes, methods, and
materials provided as per the instructions below.
CAUTION!
!

6
There is risk of fire or electric shock. Do not alter, relocate, drill or
remove any component without consulting with the Nayax certified
team.
Nayax is and will not be liable for any modifications or results of
such modifications done to the product during or after installation.
Installation must be carried out in dry conditions only.
Ensure that all power is turned off using a voltmeter or an
equivalent device before performing any installation.
Dismantle Front Panel
2
Using the Hex screwdriver, remove 10 screws to
dismantle the front panel (three from each side).
Save screws for the final stage of the process.
Install Wall Mount
1
Place the charger’s wall mount on the wall.
Drill holes. Secure the wall mount using
three M10 anchors, screws and its nuts.

7
Dismantle Internal Cable
3
Press internal yellow cable, and dismantle
front Panel.
Insert the external power cables via the hole
(bottom of the charger) and secure it with PG.
Use M3 Philips Driver for CB/MID
Connect External Power Cable
4
Connect the cables according to the diagram:
Brown = L1
Black = L2
Grey = L3
Blue = N
Yellow / Green = PE Earth \ PE \ Ground
Verify that the main circuit breaker (CB) is disconnected
and that power is turned off
L1 L2 L3 NL1 L2 L3 N
PE
S6
MJ - 0276
MJ - 0277 MJ - 0210
MJ - 0211
SIDE A
3.0 10P F 3.0 10P M
SIDE B
1 6
510S10 S5
S1

8
Attach to Wall Mount
6
To attach the charger to the wall mount,
place it firmly on the four hooks.
Assemble Charger
5
Fasten Cables using the black PG (bottom of the
charger), Power UP CB, Close the front panel and
fasten the ten screws using the Hex screwdriver.
Secure Charger
7
Fix the charger’s location using the single M4 screw to the bottom,
add Protective front cover.

Power-up
8
Turn on the main CB - Circuit Breaker (Switch I).
Make sure that the charger unit turns on,
indicated by the logo’s blue led light.
The charger is now ready for use!
Verify that the charger parts were not damaged during installation and/or that no wires are exposed.
Make sure to follow all your local electrical regulations post installation.
* If relevant for your charger model then
verify the LCD screen is turned on.
9
Connect the charger’s nozzle to the charging station.
Present a card (swipe/contact/contactless) and select the appropriate
Present a Card
2
Getting Started
WARNING!
Connect Nozzle
Inspect the charger for any visible damage.
Do not use the charger if damaged.
1
!

10
The charging status is indicated by the different logo led lights and via
the LCD screen (depending on the model).
Stop the charging process in the car. Release the latch on car's charge
port (if applicable).
Unplug the charger from the car.
Close the car's charging port cover.
Remove Nozzle
3
Charging Status Screen
4
No Light – Charger is not receiving any power (power-loss)
Flashing Blue Light – Charger initialization process
Constant Blue Light – Charger is ready for use
Constant Green light – Charging cable is connected to car
Flashing Green Light - Charging in progress
Flashing Red light – An error is detected.
Do not unplug the charger while charging.
WARNING!
!

The number of red flashing lights may indicate the following issues:
Single fast flashing – Problem with switching elements
Two flashing lights – Problem with the residual current device
Three flashing lights – Problem with the PE or neutral wire
Four flashing lights – Overvoltage
Five flashing lights – High temperature
Six flashing lights – Unsupported charging mode
Troubleshooting
This could indicate of a few issues. Start by :
Checking the car's infotainment for any error messages that could
indicate what the exact issue is.
Unplugging the charger from the car & check that the cable and
nozzle are not damaged.
Finally, check the signaling light on the charger
1.
2.
3.
If charging slows down / stops unexpectedly, what do I need to do?
11

For further assistance, contact
your local distributor at
www.lascossaelettrica.it