lab12 noyra User manual
Lab12 noyra - Multifunctional Power Distributor / Conditioner
Page 2of 7
Table of Contents
It is yours (page 3)
Unpacking and warnings (page 4)
Installation & placement (page 4)
Front panel (page 5)
Rear panel connections (page 5)
Connections (page 6)
For the safety of your equipment (page 6)
Specifications (page 7)
Lab12 noyra - Multifunctional Power Distributor / Conditioner
Page 3of 7
IT IS YOURS!
Thank you for purchasing Lab12 noyra. Noyra is an advanced power distributor / conditioner dedicated for
high end audio video systems. Adequate and clean power is critical and important for the final performance
of any audio or video device.
Keep in mind that noyra is totally handcrafted with perfectly matched parts of the finest selections.
Conductors of large cross section, star ground design, high quality tight sockets and industrial grade
bindings constitute the unshakable electrical network that delivers power to your system.
Before setting up your new noyra, we encourage you to read this manual thoroughly and get familiar with
its features.
The information contained in this manual is subject to change without notice. The most current version of
this manual is available on our official website at http://www.lab12.gr
Lab12 noyra - Multifunctional Power Distributor / Conditioner
Page 4of 7
Unpacking
Lab12 noyra should be removed from its box with care. After opening carton box, unpack noyra with your
hands on both sides of the device.
Warnings
No user serviceable parts are included inside. Do not unscrew the cover; high voltages remain after
disconnecting from mains. In case your device requires any kind of service, please ship or take your
equipment directly to Lab12 or to one of our authorized dealers or other qualified personnel.
Always use same type of fuse for replacement.
Installation & Placement
Νoyra should be placed on a solid flat surface. You should avoid placing it near a heat source as this could
compromise the performance and reliability. You should never place another component directly on top
of this device. Make sure that your noyra has an adequate flow of air around it. Noyra could be warm in
some points; this is normal and within parts specifications. Take care of the front panel finest luxury
finishing using a soft dry cloth.
Lab12 noyra - Multifunctional Power Distributor / Conditioner
Page 5of 7
Front Panel
Noyra
front pane
l
On the front panel you will see three LEDs (A), indicating that the device is powered on.
Rear Panel Connections
Noyra rear
panel
On the rear panel you will find the output sockets, main inlet and main power switch.
From the left to right are four high filtered, low current outlets (A) and two low filtered, high current
outlets (B).
On the right side of the rear panel, the main power inlet (C) and the power switch (D) are located.
Lab12 noyra - Multifunctional Power Distributor / Conditioner
Page 6of 7
Connections
Main connections
Connect a high grade 16A power cable to the IEC input and to your wall socket. Make sure that your
wall socket provides a good ground before connecting the power.
Noyra is calibrated and tested connected with a Lab12 Knack 16A power cable. We strongly suggest
to use this cable.
Connect devices
You can connect any kind of audio-video devices on the total six power outlets on the back panel
of noyra to exploit the conditioned power. Use low filtered outputs (B) to connect high current
devices (power amplifiers, plasma tv etc.) and high filtered outlets (A) for low consumption devices
(preamplifiers, cd players, DACs etc.). Live connection is always in the right pin of each outlet.
For the safety of your equipment
! Make sure that all of your equipment is turned off before any connection.
!Never exceed the maximum limits of current for low and high filtered outlets
(low filtered outlets max 3000W, high filtered outlets max 500W).
Lab12 noyra - Multifunctional Power Distributor / Conditioner
Page 7of 7
Specifications
• Number of outlets: 6
• High filtered outlets power (1-4) : 500W
• Low filtered outlets power (5-6) : 3000W
• Mains inlet: 16A IEC C14
• Mains voltage: 230V / 50Hz (115V / 60Hz)
• Available Colors: Matt Black, Frozen Silver
• Dimension (WxHxD): 43x11x29 cm
• Weight: 5 Kg
Warranty
This device has 5 years warranty from the day of purchase for all parts.
Table of contents
