Labo K Effects Spinyverb User manual

Labo ★K Effects – www.labo-k-effects.com – [e-mail]

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
2
Contents
CONTENTS 2
TECHNICAL INFO 3
OVERVIEW 4
CONTROLS 5
POWER SUPPLY 6
ADVICES 7
TROUBLESHOOTING 8
RECALL SHEET 9

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
3
technical info
COntrols
!Reverberation On/Off Switch (Verb)
!Amount of reverberation (Reverb)
!Re-injection (Dwell)
!Tremolo On/Off Switch (Spin)
!Tempo (Speed)
!General tremolo Depth
!For each time Depth by pot and L, C, R position by switch
!Attack mode switch
TECHNOLOGy
!Selected components
!Robust diecast enclosure
!Cliff et Lumberg connectors
specifications
!Consumption 60mA.
!Power: AC adapter DC 9V (not included).
!Dimensions : 7.40 (W) x 4.72 (D) x 2.76 (H)
!Weight: 27,51 Once.
Use quality mono Jacks cords only.

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
4
Overview
The Spinyverb includes a spring reverb simulator and a stereo tremolo.
Designed for use with an electric piano, it is possible to configure it for
use with a guitar.
The reverb time is 2,5 seconds and has a depth and re-injection
adjustment.
The tremolo is broken down into 4 time. For each of the 4 time it is
possible to adjust the depth and position Left, Center, Right via a
potentiometer and a selector.
These settings offer a range of very interesting rhythmic effects.
A mode selector lets you choose the form of attack tremolo. It is of
course possible to combine the two effects.
Unlike all Labo ★K Effects pedals, the Spinyverb is not True By Pass.
It is possible to use it as a splitter to feed 2 amplifiers.
Optionals accessories
Power-Link cord by Labo ★K Effects
Allows to chain the supply of several
pedals from a single power supply
using the specific cord.
Knobs for Labo ★K Effects pedals.

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
5
controls
I – THE POTENTIOMETERS
1. Time 1-2-3-4
Each knob adjusts the depth of the tremolo effect for the corresponding
time.
2. Speed
Allows you to control the speed of the tremolo.
3. Depth
This setting affects the general depth of the tremolo.
4. Reverb
This setting allows you to adjust the level of reverb.
5. Dwell
This setting allows you to determine the degree of re-injection of the
signal.
This helps lengthen the reverb and timbre change.
II – The SWITCHES
1. Position switches by time
These four switches are used to position the tremolo effect of left (L) to
the center (.) Or right (R) for each of the corresponding times.
2. Mode selector
This setting allows you to select the direction of the attack of tremolo.
3. Verb
Reverberation On/Off.
4. Spin
Tremolo On/Off.

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
6
Power supply
Labo ★K Effects pedals are powered by 9V DC battery or external
power adapter using the « Boss ™ » standard (negative (-) in the
center, positive (+) outside.
The pedal can be supplied in several ways:
!AC Power adapter.
!AC Power adapter from another Labo ★K Effects via « Power-
Link » cord.
!9V battery from another Labo ★K Effects pedal via « Power-
Link » cable.

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
7
advices
To keep the integrity of the sound, use good quality mono Jack cords exclusively.

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
8
troubleshooting
STAGE 1
No sound goes out of the device:
!Verify that all your equipment works without the pedal.
!Insert the pedal into the chain.
!If no sound output when the device is switched on, skip to step 4
STAGE 2
!If the LEDs light up correctly the device is switched on, go to step
4.
STAGE 3
If The light shines weakly or not at all and if the sound is weak and
very distorted:
!Verify the connection of the power cable.
STAGE 4
Your device is breakdown:
!Contact Labo ★K Effects by mail

Labo ★K Effects – www.labo-k-effects.com – [e-mail]
9
RECALLSHEET