Laguna Tools SmartShop MCNC-LTL-CO2-MU-2012-40 User manual

SmartShop Laser | MU
LAGUNA TOOLS
17101 Murphy Ave.
Irvine, California 92614
Ph: 800.234.1976
www.lagunatools.com
Model Numbers MCNC-LTL-CO2-MU-2012-40
ltl-CO2-MU-2420-40
ltl-CO2-MU-2420-80
MCNC-LTL-CO2-MU-2012-40
ltl-CO2-MU-2420-40
ltl-CO2-MU-2420-80
© 2017, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.

Directory
2.2 Equipment Composition............................................................................................ 7
2.2.1 Equipment Composition................................................................................. 8
2.2.2 Transmission System......................................................................................... 9
2.2.3 Optical System................................................................................................. 10
2.2.4 Control System.................................................................................................11
2.2.5 Peripheral equipment....................................................................................... 12
2.3 Front of the Machine...................................................................................................15
3.Equipment Installation........................................................................................................... 16
3.1Preparation before Installation.....................................................................................16
3.1.1 Site Preparation.............................................................................................16
3.1.2 Personnel Preparation................................................................................... 16
3.1.3 Tool Preparation............................................................................................16
3.1.4 Other Preparation.......................................................................................... 17
3.2 Installation procedure..........................................................................................................17
3.2.1 Package of Laser Tube.................................................................................................. 17
3.2.2 Installation of Laser Tube................................................................................ 17
3.2.3 Water Pump Installation...................................................................................18
3.2.4 Exhaust Fan Installation................................................................................20
3.2.5 Air Pump Installation.................................................................................... 20
3.3Ground Line Connection..............................................................................................21
4 Equipment Debugging........................................................................................................... 21
4.1Inspection before Debugging.......................................................................................22
4.1.1Boot Process..............................................................................................................22
Power On:..........................................................................................................................22
4.1.2 Test Running................................................................................................. 22
4.2 Laser Debugging......................................................................................................... 22
4.2.1 Output of the Laser Tube................................................................................. 22
4.2.2 Laser Path Debugging......................................................................................23
4.2.3Test Processing..................................................................................................28
5. Simple operating instructions................................................................................................29
5.1 Simple operating instructions..................................................................................... 29
5.2Data line using operation............................................................................................. 31
5.2.1 Parameter Matching......................................................................................... 32
5.2.2 Make simple pictures&Set picture layers........................................................37
5.2.3 Set working mode......................................................................................... 39
5.2.4 Download files................................................................................................. 40
5.2.5 Equipment Operation............................................................................................... 41
5.3 U-disk Operation.................................................................................................................43
6. Rotary Processing..........................................................................................................................45
6.1 Electrical Installation.......................................................................................................... 45
6.1.1 Rotary Connection................................................................................................... 45

6.2 Software Operation............................................................................................................. 46
6.2.1 Software Setting.......................................................................................................47
6.2.2 Cutting Test.............................................................................................................. 50
7. Equipment maintenance and repair...............................................................................................54
8. CO2 Laser Tubes of Glass Usage Considerations................................................................ 56
Preface
Thank you for choosing our products. We will provide you with
comprehensive after-sales service and solutions, please keep this
instruction booklet and other attachments for your better use later.
This statement only applied to our standard equipment, for special
ordered Machine, please read the attached documentation.
The Manual is going to show you the work Principle, methods of
installation, operation, troubleshooting, transport and storage and

maintenance. If it’s your first time to use this product, please read this
information carefully before installation and use.
For quick and efficient using this equipment, the user should meet
conditions as below:
A. Operator requires a certain amount of computer expertise to edit the
graphics software ,For Example:
Coreldraw,Photoshop ,Autocad and other CAD software.
B. Operators have a certain knowledge of optics and electrical related
equipment repair and maintenance
C. Confirmed that the operator is familiar with the equipment operating
procedures before starting the and do as it’s instruction.
Apologized that due to the constantly product updated,maybe somewhere
is different with your products.
Brief Introduction of Laser Engraving Machine
1. Safety knowledge
1.1 Basic Information
● Make sure that the operator is trained before operating the machine.
● In order to avoid unnecessary loss,the operator is prohibited from
leaving and must observe the machine at all the times when it under
working.
1.2 Optical Security

Our Equipment Adopts the Fourth Laser that the wavelength is 10.6μm,
Recommended that the operator wear the accredited laser protective
glasses.
Even wear the laser protective glasses and do not look directly at the laser
beam or any reflection of the laser beam.
1.3 Electricity Security
Observe the machine nameplate carefully such as power and voltage
requirement before you access the power supply.
Without our permission,please do not disassemble the electrical parts
yourself .Especially do not touch the laser power supply ,laser tube when
it s working because of its lethal voltage,the danger still exists even
power outage.
1 Hazard
a wide variety of potentially dangerous substances that produced by the
plastic materials when processing can be removed by the ventilation
systems,if the smoke or the smell is too big ,the gas mask is needed.
2 Other hazards
For security purposes,Equipment modification is strictly prohibited
without the manufacturer agreement.
2. Equipment Brief Introduction
Equipment adopted the high-precision transmission shaft and servo-drive
can be realized fast and smooth carving.Non-Metal materials can be cut
or engraved by the high efficiency laser tube.
※※※一※※※※一※※
Machine Series :
BCL:
bodor cutting laser
BML:
bodor marking laser
Working area：
0503:500mm×300mm
0605:600mm ×500mm
1006: 1000mm×600mm
1309: 1300mm×900mm
1610: 1600mm×1000mm
… ……
Model description：
M: Mini Series
X: Standard Series
B :Laser Cutting Bed
FB:Fiber Laser Cutting Series
YB/YT:YAG Laser Cutting Series
FP:Fiber Marking Series
additional devices
U:Up-Down System

1-1 Machine Model Description
Example:BCL1309XU means working area:1300mm×900m with up-down system.
2.1 Nameplate Introduction
The nameplate fixed on the right rear of the device which can get more
equipment information.No randomly change or demolition.

2.2 Equipment Composition
Machine Appearance or the some details are different because of the
model or Machine improvement.Specific to the material object as the
standard.
Liner Guide
Laser Head
Slider
Belt
Red Dot System
Nozzle Connector
Unique Equipment Number

2.2.1 Equipment Composition
Laser
Machine
Machine
Body
Transmis
sion
System
Optical
System
Control
System
Peripheral
equipment
Tool Box
1
2
3
4

Picture 1: Machine body： body、 transom、 upper shield,Up&Down table
1-Liner Guide 2-Laser head 3-Slider 4-Belts 5-Stainless Steel Working
Table 6-Photoelectric switch 7-Nozzle Connector 8-Red Dot System
2.2.2 Transmission System
8
5
6
7
Motor
Transom
Transmission Shaft

Picture 2: Transmission System is Composed of Motor ,Driver ,
Transmission Shaft,Liner Guide,Slider,Belt.
2.2.3 Optical System
Note: Laser tube must be handled with care during installation;High
Voltage and Cathode lines should be tense properly;Water inlet on the
upper and outlet on the below(Reci Tube);Ensure that no bubble inside
the tube;Evenly Strength on both sides when fix the laser tube on the
Basement.Make sure it Solid and not crushed.
Liner Guide
Belts
Slider
Belt

Picture 3:Optical System :Three Reflectors and Focal Lens Device
2.2.4 Control System
Control Systems are different because of the machine model,Specific to
the material object as the standard!
Our control systems as below :Leetro 、Ruida
Ruida Control Panel Ruida Control Card
First Reflector
Second Reflector
Third Reflector
Focal Lens

Leetro Control Panel Leetro Control Card
Picture 4: Control System:Control pane, Control Car,Computer
Control Card
Power Supply
Laser Power Supply
Data Line
Driver
Relay

2.2.5 Peripheral equipment
Picture 5: Peripheral equipment:Water Pump,Exhaust Fan ,Air Pump
2.2.6 Tool Box
Exhaust Fan Socket
Water Pump
Air Pump

Picture 6 Tool Box
Note:Tool Box is different because of the machine model,Specific to the
material object as the standard.!
Limit switches :Proximity switches and Micro switches
Certification
Data line
Power Supply Line
Limit Switch
Adhesive Tape
High pressure tape
U Disk
CD
Water/Air Pump
Fork wrench
Laser Path
Adjustment Block
Allen wrench
Focus Distance Block
shovel blade

shovel blade Usage Focus Distance Block Usage
Picture 7 Shovel Blade Focus Distance Block
2.3 Front of the Machine
Picture 8:Control Panel
Focal Distance Block
On/Off button
Emergency Stop
Control Panel

Picture 9: Machine Power Supply Socket
3.Equipment Installation
3.1Preparation before Installation
3.1.1 Site Preparation
Equipment should be set in dry environment without electromagnetism
and high-strength electricity, without pollution's disturbance and effect.
Temperature of working environment is 10-38℃, humidity is 10-90%,
AC 220V±10%, 50HZ,resistance to ground should be smaller than 5Ώ.
3.1.2 Personnel Preparation
The operator must master the main point of installation. Otherwise, the
damage of machine parts will not in our scope of protection.
Three-hole Strip
Ground Line Connector
Fuse
Power Supply Connector
Water inlet
Water Outlet
Air Pump Connector

3.1.3 Tool Preparation
There is tool box with this machine. Besides, multimeter and screw driver
and other detection tools are needed.
3.1.4 Other Preparation
Purified water for water chiller, power strip, pipe for discharge smoke,
sample material, etc.
3.2 Installation procedure
3.2.1 Package of Laser Tube
In case of damage during transportation or outside force, the tube is
packed with sponge. And two ends of tube are sealed with zip lock bag to
prevent the mirror from pollution or scratch. Finally, the tube is built up
with sponge supports to prevent tube have direct contact with
surrounding.
3.2.1.2 Open the carton box, take out the laser tube. Both hands hold the
middle of the tube; take off the sponge supports; take off the packing
sponge; take off the zip lock bag. Then inspect whether the tube is intact.
If tube have any defect, please take photo and send to Bodor for
confirmation.
Attention: It needs as least two person when remove the package. Handle
the tube with care.
3.2.2 Installation of Laser Tube
Open the back cover. You can see two white laser basement, two water
pipes, and black color low-voltage line and red color high-voltage line.

Picture 10:Laser Tube Installation
3.2.2.1
Use Allen wrench M3 take off the screws that fix the laser tube and
remove the upper parts.
Put the low voltage side of the laser tube on the basement that nearby the
First reflector mirror.
Put back the basement upper parts and fix the screws.connect the high
voltage socket and water inlet and outlet pipe.Fix the laser tube well as
Picture 10.
Notice:
●Distance is 2cm between the laser Output and the first reflection mirror.
●Do not too tense to crush the laser tube.
●Solid connect the water inlet pipe to prevent the water leakage.
●Laser Tube inside water flow from the high pressure side to low
pressure side,start to work without bubbles
High Voltage
Basement
Low-Voltage
Water Outlet
Water Inlet
Water Flow Direction

3.2.3 Water Pump Installation
Picture 11 Water Pump
▲Find one container, fill in purified water or distilled water.
▲Put the water pump into this container.
▲Connect the water pump Outlet with the machine water inlet by water
pipe.
Picture 11 Water Pump Installation
Notice：
●Laser Tube inside water flow from the high pressure side to low
pressure side,Or broken the laser tube.
●When powered on, the bubble in the tube can be removed by extruding
the water pipe or turning the laser tube.
Water Outlet

●Do not touch high voltage lines during working or shut down the
machine for a while,or may cause an electric shock and threaten safety.
3.2.4 Exhaust Fan Installation
Picture 13: Exhaust Fan Connection
Attention ,Exhaust fan is different because the model,Specific to the
material object as the standard.
Exhaust Fan
Air Pipe
Clamp